Plumbworld IN00050 User manual

IN00050 (rev D)
Two Panel Sliding Bath Screen
Instruction suitable for both Right and Left Hand Fixing•

Check that the bath has been installed correctly•
and that it is level (Fig. A), tiled down onto and
sealed to the manufacturerʼs guidelines. Please
Note: All product supplied without bath.
Check that there is sufficient space on the bath•
for the product and that the screen movement
does not foul other items such as sinks and
taps.
Ensure the product is fitted to a non-porous•
surface ie. tiled. Check that the wall surface is
flat.
Unpack and check the product is complete and•
undamaged.
Fixings are supplied for solid walls only. Ensure•
that the correct fixings are used for the wall type
– if in doubt seek professional advice
Ensure the area is clean, dry and dust free.•
Read the instructions in full.•
Have the correct tools available, (as shown•
below, see ʻTools Requiredʼ).
Handle all glass with care - support on cardboard to avoid risk of breakage.•
This product is heavy and requires 2 people to carry and install it.•
When drilling walls check first for hidden pipes and cables.•
All glass is toughened – it cannot be reworked or replaced by ordinary glass.•
Use safety eyewear when drilling.•
Use safety eyewear when handling glass.•
Keep all small parts away from children.•
Safety
Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held•
responsible for any installation costs that may arise from damaged or faulty product being installed.
Please dispose of all packaging with due regard to the environment.•
Disclaimer
Before You Start
Tools Required (not supplied)
Fig.A.
Spirit Level Screwdriver Tape Measure
Junior Hacksaw
Pencil Utility Knife
Silicone Gun & Sealant Power Drill Suitable Drill Bits
6mm dia. *
3mm dia.
HSS
* Ensure drill bit
used is suitable for
wall surface
Help Line: 0870 241 6131 Lines open: 8.30am - 5.00pm Monday to Friday
Standard National call charge rate from BT landlines

Parts & Fittings Supplied Please notify the retailer immediately
of any damage or faults. The
manufacturer cannot be held
responsible for any installation costs
that may arise from a damaged or
faulty product being installed.
!
Keep small parts away from children
!
D1
Bath Screen
Assembly
X1
Oversized Horizontal Seal
(Cut by suit)
X1

No.8 x 1” Pan Head Pozi Screws x3
(actual size)
Qty
A
Wall Plugs x3
(actual size)
Qty
B
No.8 x ⅜” Pan Head Pozi Screws x3
(actual size)
Qty
C
Screw Cover Caps x3
(actual size)
Qty
D
D1
Loose Screws & Fittings Supplied
Wall Channel
X1
A
D
B
C

Horizontal Seal Preparation
i)
Apply to 1 cut
down seal only.
Cut Horizontal Seal in to 2 pieces.
ii)
iii)
X1 X1

1
1.1
1.2
1.3
Remove cover cap
Slide Horizontal
Seal into position
Trim Horizontal Seal overlap
Replace cover cap
1.4
1.5
Tie end of seal into
tight knot
Pull seal back to
remove any slack
Inside View
Inside View

2
Remove cover cap
Slide Horizontal
Seal into position
Trim Horizontal
Seal overlap
Replace cover cap
2.1
2.2
2.3
2.4
Inside View
Inside View

3
3.1 Tip:
When drilling tiles apply masking
tape to surface to stop drill bit
slipping.
*
Wall plugs supplied are for solid
walls only. Ensure correct wall plug
for wall type is used. If in doubt seek
professional advice.
!
Position wall channel on wall.
Ensure channel is vertically level
and does not overhang the bath.
!
BATH
SIDE
OUTSIDE
FACE
Please Note:
Position Wall
Channel with
curved side
facing away
from bath.
!
3.2
3.3
Mark position
pre-drilled Wall
Channel holes
6mm dia. holes with
drill bit suitable for
wall surface
A
B

BATH
SIDE
OUTSIDE
FACE
4
5
Inside View
D
C
5.1*
5.2
* 3mm dia. holes through
pre-drilled wall channel holes
using HSS drill bit
Inside View
Please Note:
Ensure Horizontal Seal
sits on top of bath.

150mm
7
Apply Silicone
Sealant, (not supplied).
!
Product Care:
Use a non abrasive cleaner.
Water marks may be removed
with a proprietary limescale
remover or household
vinegar.
*
Only apply sealant to the outside
of the Bath Screen.
DO NOT use silicone sealant on
inside of the Bath Screen.
!
6
Apply a small amount of
Silicone Grease from sachet
(supplied) to the hinge
mouldings.
!
6.1

Notes:

Notes:

Check out our full range of Shower Enclosures
Quadrant Shower Enclosures
Corner Entry Shower Enclosures
Walk in Shower Enclosures
Sliding Shower Doors
Bifold Shower Doors
Pivot Shower Doors
Hinged Shower Doors
Shower Screens
From Top Brands
Coram Shower Enclosures
Mira Shower Enclosures
Hydrolux Shower Enclosures
Diamond Shower Enclosures
With quality shower trays to match your enclosure
Square Shower Trays
Rectangular Shower Trays
Quadrant Shower Trays
Coram Shower Trays
Mira Flight Shower Trays