Plumbworld 600A Macerator User manual

600A Macerator
Installation Requirements
Customer Care Helpline
Telephone: [phone]
Email: [e-mail]
Inputs
The macerator can be used with multiple
inputs, or just one. Blanking plates are
provided to help you.
Installation
The electrical installation of this product must
be done by qualified persons only.
This macerator is only for use with a toilet
using a horizontal outlet. The toilet must also
have a flushing tank or tap. Note: the
horizontal outlet must be 18cm above floor
level in accordance with EU standards.
Discharge pipe length to the first elbow must
be a minimum length of 0.5m.
Toilet Only Configuration
Place this horizontal toilet outlet into
the macerator, and clamp the rubber
sleeve of the macerator around the
pipe using the supplied jubilee clip.
Repeat for the 32mm or 40mm
discharge pipe.
Electrics: The unit must be installed to comply
with current UK electrical regulations, with a
fused spur rated at 3 amps. We advise that
this is done by a registered electrician.
This appliance must be earthed.
If the supply cord is damaged, it must be
replaced by a qualified person. The cable
type is H05VV-F, 3G0.75mm2 VDE. The IP
rating of this appliance is IP55.
Water: The unit is designed for a horizontal
toilet outlet with the standard European 18cm
to the outlet centre from the floor. All other
inlets must be gravity fed into the unit. The
outlet comes as standard with a 32mm
connection however 22mm can be used with
a reducer. If using bends in the connecting
pipe work ensure they are smooth curves to
avoid blockages.
Specification: Water temperature should be a
minimum of 1°C it is important that the unit
does not freeze, and a maximum of 40°C.
Maximum vertical discharge 9.5 m. Maximum
horizontal discharge 60m.
plumbworld
Big brands, small prices.
Discharge pipe
mustbe32mm
or40nmonly
NOTE DIRECTION OF
Secure macerator to pan with largeJubilee
clip , ensuring h Is fully tightened
plumbworld
Big brands, small prices.

600A Macerator
Configuration with Other
Appliances
Connect the discharge pipes of each
appliance to the rubber connectors provided
and clamp with supplied jubilee clamps.
For use with a bath or shower, there must be
a gradient of 1cm per metreor greater. If
used with a shower, a second check valve
must be used. This must be fitted between the
macerator and the tray. If other appliances are
fitted along the discharge line, check valves
must also be used on these.
Prior to first use flush a large quantity of clean
water through the unit.
General Care and Maintenance
Daily Usage:
This product is suitable for indoor
use only.
Do not put foreign objects, such as but
not limited to condoms, sanitary
towels, and wet wipes through the
system as this will cause damage to the
unit, and will invalidate your warranty.
Servicing:
•Service and cleaning should be
performed once every 6 months.It is
recommended that this is done by a
professional.
•Before servicing, ensure the electric
supply is off.
•Appropriate PPE must be used whilst
servicing the unit.
Warranty
Please note the following situations that will
invalidate the warranty:
Failure to install the appliance in
accordance with this installation guide.
Installation by unqualified persons.
Foreign objects in the system.
Failure to carry out regular
servicing/maintenance as detailed in
this guide.
Product Disposal
This product should not be disposed
of with other household wastes.
To prevent possible harm to the
environment or human health from
uncontrolled waste disposal, the unit
should be disposed of at an
appropriate local authority facility.
The symbol on the appliance states
that it meets the new directive
(2012/19/EU) and must be handled in
accordance with this standard at the
end of its service life.
•
Ut il'i ly Sink,
D islhwa;s her, ~
Waslh ing1IMachir u:
Toilet
~ Dischafge Piipe
i;;;;:, Balh, S!hO'l!Ve r,
Balhroom 1
13.as in
plumbworld
Big brands, small prices.
plumbworld
Big brands, small prices.

600A Macerator
Trouble Shooting
Symptom
Cause
Resolution
The macerator has cut out
The device has overheated.
Leave the unit to cool for 30
mins, switch it back on and hold
the override switch to reset the
unit. Check for blockages.
The macerator has cut out
Power supply has been
interrupted
Check fuses and power supply.
The water is back flowing
Insufficient gradient
Ensure a gradient of 1cm per
meter is used.
The unit is leaking.
Check valve/jubilee clips are not
fitted correctly.
Check these items.
The macerator is non-
operational and has never been
opened.
The macerator is connected to
an incorrect size pipe.
Ensure the pipe is 32 or 40mm.
The electrical install was
incorrect.
Ensure the device was installed
by a qualified person.
The check valve is facing in the
wrong direction.
Check the check valve(s).
Pressure switch is blocked
Check/replace the pressure
switch.
The macerator is not powerful
enough.
Discharge pipes are too
long/high
Check the distances against the
spec.
Discharge pipe is to small
Check the sizes
Unit is blocked.
Service as per instructions
above.
The macerator emits a
humming noise but does not
discharge waste.
Pump is blocked
Check/service pump.
Check valve is installed the
wrong way round.
Check the check valve.
The macerator discharges waste
with no demand.
Check valve is faulty
Examine/replace the check
valve.
The tank is leaking
Check the tank.
There is a partial blockage
Clear the blockage
Pressure switch is defective
Replace the pressure switch
Macerator is not emitting a
humming noise.
The unit is not properly
connected to the electric supply
Check the supply
The pressure switch is not
connected.
Check by pressing the override
switch several times.
The motor is not operational
If pressing the override switch
has no effect the motor may be
dead.
plumbworld
Big brands, small pr ices.
plumbworld
Big brands, small prices.

Check out our full range of macerators
Saniflo Macerators
Flo-Force Macerators
Stuart Turner Macerators
Grundfos Macerators
Don’t Forget These Macerator Accessories from Saniflo
Saniflo Sani Alarm
Saniflo Descaler