PMT AS7.U050.003-1 User manual

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | [email protected]
WWW.PRECISIONMOUNTS.COM
RUGGED USB-C HUB
Description Part Number
Rugged USB-C Hub with bare wire power cable AS7.U050.003-1
Rugged USB-C Hub with bare wire power cable and USB-A to USB-C
Cable AS7.U050.003
Rugged USB-C Hub with bare wire power cable and USB-C to USB-C
Cable AS7.U050.003-2
USER GUIDE

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | [email protected]
WWW.PRECISIONMOUNTS.COM
GENERAL INSTRUCTIONS
Safety:
•Safety is dependent on the proper installation and servicing of this product. It is important to read and follow all
instructions before installing this product.
•Proper installation requires a good understanding of automotive electrical systems and is recommended to be
performed by qualified technicians only.
•There are no adjustments or user serviceable parts within this product. Opening the case will void the product
warranty
•Do not install equipment or route wires in the deployment path of any air bag, or where it may interfere with critical
safety or operating controls of any vehicle.
Power:
•The power input should be 10-40Vdc / 5 A (@12vdc nom). PMT recommends using a Lind DC adapter.
•DC-DC Power supply must comply with local jurisdictions.
Wiring:
•PMT does not recommend relying on a cigarette socket adaptor for power. We recommend hard wiring the power
adapter using a good clean ground direct from the vehicle battery neg(-) post, and pos(+) supply from a fused
12Vdc location also directly from the vehicle battery. All peripherals connecting to a docking station requiring
external power should get power and ground from the same location as the dock.
•Visit www.precisionmounts.com/support/installation-user-guides.html for a copy of our general wiring and
troubleshooting guide.
Proper Use and Care:
•Proper care and use of this product is critical to maximize safety and to prevent damage to the hub.
•Do not store, place, or drag any object on top of the hub.
•Discontinue use of this product if the power cables are damaged, or if the unit comes into contact with a liquid
substance
•Any modifications made to this product could result in adverse performance and damage to the host device and/or
hub and will void the warranty.
Environmental:
•Storage: -40°C to 85°C (-40°F to 185°F)
•Operating: -20°C to 70°C (-4°F to 158°F)
SERVICING [ENTRETIEN]:
•If this product does not work as intended, please contact PMT for troubleshooting or to schedule a service. [Si le
dock ne fonctionne pas comme prévu, contactez PMT pour le dépannage ou pour planifier un service.]
•Service should be only done by authorized service center personnel. Unauthorized servicing of the unit will void its
warranty. [L'entretien du dock ne doit être effectué que par le personnel du centre de service autorisé. Un entretien
non autorisé du dock annulera sa garantie.]
Product Mounting Disclaimer
Precision Mounting Technologies Ltd (PMT) are not liable under any theory of contract or tort law for any loss, damage, personal injury,
special, incidental or consequential damages for personal injury or other damage of any nature arising directly or indirectly as a result of
the improper installation or use of its products in vehicle or any other application. In order to safely install and use PMT products full
consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brake lines, electrical, drive train or other systems), air-
bags and other safety equipment is required. PMT specifically disclaims any responsibility for the improper use or installation of its
products not consistent with original vehicle manufactures’ specifications and recommendations, PMT product instruction sheets, or
workmanship standards as endorsed through PMT policies and EULA.

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | [email protected]
WWW.PRECISIONMOUNTS.COM
DESCRIPTION OF PARTS
Cable tie
rail
Mounting
holes
VESA75
“P” clip x2
HDMI
Gigabit
Ethernet
RJ45
2x USB
3.0 Type A
900 mA
2x USB 3.0 Type A
Fast Charging
1.5 A
DC input
10-40 VDC
USB 3.0 Type C
Fast Charging 1.5 A
data input

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | [email protected]
WWW.PRECISIONMOUNTS.COM
INSTALLATION
Step 1:
Connect all cables as shown utilizing the
cable tie rail and plastic zip ties to fully
support each cable. Wrap the power and data
in cables around and through the plastic “P”
clips
Step 2:
Mount the hub using the 4x holes to your
VESA 75 compliant equipment or location
Step 3:
Attach data cables to peripherals and host
Step 4:
Connect power cable to power source. If
using the bare wire input cable connect the
red wire to a fused positive battery source,
and the black wire to negative ground.
Tip: Visit our website to search for and review our “General wiring and
troubleshooting guide” for further information.
Plastic zip ties used to
secure cables to Cable
Tie Rail
“P” clips used to secure
power and USB-C
cable
Notes:
1. Data input must go through the USB-C port on the hub.
2. HDMI functionality within Windows only when used with Thunderbolt 3 USB-C cables and
compliant hosts.
3. Compatible with Samsung DeX

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | [email protected]
WWW.PRECISIONMOUNTS.COM
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions. (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Certifications and test standards:
EN 55032: 2012 / AC: 2013, Class B
EN 50498:2010
Made in Canada
Regulatory model: 7160-1393