Channels can be taught via PocketWizard Utility or from any
PocketWizard Transmitter using LEARN mode:
IMPORTANT: Hold units at least 2 feet apart when teaching/learning.
1. Turn MiniTT1 or FlexTT5 unit ON and select Channel to be taught.
2. Press and hold TEST for several seconds until LED blinks amber, then release TEST.
3. Quickly press and hold TEST on teaching Transmitting unit (MiniTT1, FlexTT5, Plus II
or MultiMAX). When LED blinks green, channel is learned. Connected flash may
trigger during LEARN.
1 green blink = Low Legacy Channel learned (1 through 16)
2 green blinks = High Legacy Channel learned (MultiMAX 17 through 32)
3 green blinks = ControlTL Channel learned (ControlTL 1 through 20)
For remote TTL systems, teach MiniTT1 unit to be used as primary transmitter first,
then use it to teach all FlexTT5 units.
MiniTT1 and FlexTT5 units send out both ControlTL and Legacy triggers every time
they are triggered. For remote TTL to function, ControlTL channel must be learned.
If you see only 1 or 2 green blinks, and you desire TTL, teach again with MiniTT1
or FlexTT5 unit. Look for 3 green blinks to verify ControlTL is learned.
To teach all units Legacy channels, use Legacy Transmitter as teaching unit for all
learning units, including MiniTT1 unit to be used as primary transmitter.
To avoid inadvertent flashing from remote units that have already been taught or
have already had channel set, turn them OFF.
MiniTT1 00 Plus II, MultiMAX, Integrated, or FlexTT5
connected to manual flash
Remote flash with or without TTL flash on camera
1. Slide MiniTT1 Transmitter onto camera.
2. If desired, slide Canon E-TTL Speedlite (MASTER = ON) onto MiniTT1 unit.
3. Make sure all your PocketWizard units are on the same Channel and trigger normally.
Note: Manual remote flashes are not calculated as part of the E-TTL exposure.
Be sure to set on-camera FEC if remote flash is illuminating same subject as
your E-TTL flash.
ZeroSync™occurs automatically. Trigger “as fast as a wire” with all PocketWizard radios.
Use PocketWizard Utility to engage HyperSync™and explore faster than X-sync shutter
speeds. See user manual at www.pocketwizard.com for more information.
Auto-Relay Mode
A FlexTT5 unit in camera’s shoe and connected with motor drive cord to P1 can receive
a radio trigger, trigger the camera’s motor drive which in turn triggers a remote flash.
The channel used for relay transmit is 1 higher than taught channel, unless set via
PocketWizard Utility.
Example: if you taught FlexTT5 unit Channel 3 then relay transmit occurs on Channel 4.
Press TEST on hand-held trigger unit to begin relay sequence.
Status LED
Normal “waiting for trigger” operation = short blink every 2 seconds.
Normal short blink color indicates Battery Level:
Green Good battery
Amber Warning – battery low
Red Very low battery – change immediately
Steady red LED in sync with TEST indicates normal transmission.
(Hold for 10 seconds to teach – see LEARN mode)
Short red blink in sync with trigger indicates normal reception.
Rapid red blinking when not triggering or half-pressing camera indicates error condition.
Power off the unit, reseat all connections, and power back on.
Manual FlashLEARN Mode Other Functions
Specifications
Trigger Delay = 0 seconds – “fast as a wire”
Batteries: MiniTT1 = CR2450 or CR2354 (100s of hours)
FlexTT5 = 2 x AA (IEC:LR6) (60 hours)
Powerable via USB AC adapter (powering from computer USB port not recommended)
Maximum FPS: Up to 12 (varies with camera, E-TTL usage reduces FPS)
E-TTL: E-TTL I & E-TTL II (DSLR only, not for film TTL)
Operating Temperature: Above -15 C (5 F) and below 50 C (120 F)
Storage Temperature (without battery): Above -30 C (-22 F) and below 85 C (185 F)
For more information on this product,
including detailed features, specifications
and the complete user manual, go to
www.pocketwizard.com.
This product is covered under a warranty. For more information
on the warranty and to register your product, please go to
www.pocketwizard.com/support.
This US FCC/Canada IC frequency
PocketWizard radio slave is compatible with
all US frequency PocketWizard products. It is
not frequency compatible with CE or JAPAN
PocketWizard products. Verify frequency
compatibility before purchasing.
© 2009 LPA Design, Inc. All rights reserved. Product features and
specifications are subject to change without notice. PocketWizard,
ControlTL, MiniTT1, FlexTT5, HyperSync, ZeroSync, Plus II and MultiMAX
are either trademarks or registered trademarks of LPA Design, Inc.
All other trademarks contained herein are the property of their
respective owners.
US Patent: 5,359,375 and Patents Pending
V1.0 – January 2009 – LPF374
www.pocketwizard.com
MAKE IT POSSIBLE™
RESET to Default Settings
RESET A: To reset Learned Channels, hold TEST on power up. LED blinks green twice
to indicate reset. Release TEST. Advanced Features set via USB are retained.
A: Default Channels
C1 = ControlTL Channel 1, Legacy Channel 1
C2 = ControlTL Channel 2, Legacy Channel 2
RESET A & B: To reset all Advanced Features and Learned Channels to FACTORY DEFAULTS,
hold TEST on power up for longer than 10 seconds. When LED blinks green
4 times, release.
B: Default Advanced Features
Auto ISO and Aperture Tracking Enabled
Exposure Compensation Center Value = 3.5
HyperSync Offset = -250 microseconds
Remote TTL Flash Sleep Mode = Disabled
Camera Model = Auto
All settings may be configured using the PocketWizard Utility available from www.pocketwizard.com
