POER PTR16 User manual

User Manual
Wireless Programmable
Room Thermostat
Model No. : PTC10/PTR16
Power to control your heating
Anytime, Anywhere
smart controls
Scan for App
Add.: 19th. Floor, Xingtu Building, No.451
Wulianwang Street, Binjiang Zone, Hangzhou
City, 310051 Zhejiang Pro., CHN.
www.poersmart.com
Zhejiang Lancable Tech., Co., Ltd
Tel.: [phone]
Fax: [phone]
E-mail: [email protected]

01
1. Overview
This wireless programmable room thermostat kit can be used to control high-power
heating equipment on electric heating or infrared heating; but also be applied to low
power AC(Alternating Current) devices like electric actuators.
It contains a wireless programmable room thermostat PTC10 and a wireless receiver
PTR16, the two units are linked by Radio Frequency. (If your kit is Wi-Fi thermostat,
there is a gateway PTG10 accessing your thermostat to internet?)
This thermostat is a programmable room thermostat 5+2 Days / 7 Days/1 day product.
5+2 days allows you to set a program for weekdays and a program for the weekend. 7
days allows you to set a same program for every day of the week. 1 day functionality
allows you to set a different program for every day of the week. Each program type
allows you to set 7 time and temperature events.
Controls and Display Layout
A
B
C
D E G
H I
J
K
EF
Days
Temperature
Auto, Manual Holiday mode,
Time
RF
ECO
Copy Clock set
Child lock
Program set
Forst protection
Heating
Low bettery warning
Open window
Confirm
Return
Humidity
Program setting time
+
adjustment
or - buttons for setting
A
B
C
D
E
F
G
H
I
J
K
Contents
LEARN
LEARN MODE
OVERRIDE
EMPTY BUTTON
LEARN MODE
Ⅰ
Ⅱ
Ⅰ
1. Overview
2. System Installation
2.1 Install and Wiring Receiver
2.1.1 Install Receiver
2.2 Activate Batteries and Install Thermostat
2.2.1 Activate Batteries
2.2.2 Install Thermostat
2.3 System Check
3. Operation Thermostat
3.1 Clock Setting
3.2 Program Setting
3.2.1 Pre-set Program
3.2.2 To adjust the Pre-set Program
3.3 Override Mode
3.4 Manual Mode
3.5 Holiday Mode
3.6 ECO Mode
3.7 OFF Mode(Frost Protection)
3.8 Child Lock
4. User Option
5. User Options Table
6. Product Specification
Wireless Programmable Thermostat
Wireless Receiver
01
02
02
02
04
06
06
06
07
07
2.3.1 RF Signal Pairing
2.3.2 RF communication test 14
16
16
18
18
18
21
22
23
24
25
25
26
27
28
28
29
2.1.2 Receiver’s wiring

02 03
2. System Installation 2. System Installation
2.1 1 Install . Receiver
Follow the installation diagrams to install and connect the receiver PTR16 correctly.
2.1 Install and Wiring Receiver
Note: 1 The installation and wiring should be operated by trained personal.
Note: The Receiver should be mounted in a suitable location that is both accessible for
the connection of mains and control wiring, and allows good reception of the RF signal.
The Receiver needs a 100~240V AC mains supply to operate, and this should be fused
appropriately (16A max.).
2
Note:
with water, moisture or condensation.
3 The Receiver should be mounted in a location where it will not come into contact
Note: 4 Before wiring the terminals, please check the wiring drawings carefully.
A B CABC
NL
2
max 2.5mm
A B C A B CNL
ABC A B C
NL

04 05
2. System Installation 2. System Installation
L N
Burner (direct control)
N L A B C A B C
AC
230V
Imax
IN
16A
50Hz
L1 N1
NTC
N L A B C A B C
AC
230V
Imax
IN
16A
50Hz
L1 N1
NTC
L N
Electric heater
Thermal actuator
R B BL BR
N L A B C A B C
AC
230V
Imax
IN
16A
50Hz
L1 N1
NTC
Zone Valve
G/Y BR BL GR
M
0
N L A B C A B C
AC
230V
Imax
IN
16A
50Hz
L1 N1
NTC
Wiring Figure:
2.1 2 Receiver’s wiring.
Contacts:
N L A B C A B C
AC
230V
Imax
IN
16A
50Hz
L1 N1
NTC
230VAC 50Hz<16A β3380 R25 10KΩ= °C=
Wiring with AC230V power supply in NTC sensor terminals will destroy
the receiver!
Thermostat kit do not contains external temperature sensor NTC terminals.

06
2. System Installation
81.5mm
81.5mm
4mm
2.2.1 Activate Batteries
2.2.2 Install Thermostat
This thermostat could be desk-stand if open the back support, you just need to place it on
any flat surface allows to receive RF signal.
If you want to hang it on the wall, use the template provided.
Drill two holes in the wall and tighten the screws, ensuring two holes’ distance is 81.5mm;
then, fix the thermostat’s back cover by putting it over the screw head.
Remove the battery cover Insert batteries, ensure
correct orientation Close the battery cover
2.2 Activate Batteries and Install Thermostat
07
2. System Installation
2.3 System Check
2.3.1 RF Signal Pairing
The room thermostat has already been pre-bound with receiver
in kit PTC10/PTR16 when delivery. You may directly move to RF
communication test, please refer to 2.3.2.
i
A. RF signal pairing between room thermostat and receiver
1 Preparation: thermostat and receiver should be powered/wired correctly, make sure the
visible distance between thermostat and receiver is not more than 5 meters.
2 Start receiver s RF paring mode by hold-pressing the LEARN button until its light
flashing.
’
3 Press OVERRIDE Ⅰ to pair with thermostat; when light of OVERRIDE is flashing, it
means OVERRIDE Ⅰ is ready to pair with thermostat next.
Ⅰ
（3-1）Long press to enter Menu Selection, select by pressing or
when are flashing, press to enter RF pairing interface.
4 Thermostat send pairing command with receiver:

08 09
2. System Installation
1 Automatically pairing thermostat with gateway by App on mobile phone
B. RF signal pairing between room thermostat and gateway this is only for Wi-Fi
thermostat)
(
（1-1）Open the App. which already connected with gateway(how to add a gateway on
App. please refer to gateway’s manual for details), choose Add Thermostat from the
interface;
（3-2）When is flashing on the screen’s left side, press to send the pairing
command with receiver;
Pairing success if flashing on screen’s right side, pairing failed if E01 or E02 is
flashing on screen’s right side, in this case, you need to send the paring command with
receiver by pressing once again until pairing success.
4 Exit pairing mode: Exit pairing mode by pressing LEARN button; thermostat s HOME
page can be returned by keep pressing .
’
5 Once thermostat and receiver was paired successfully, their RF communication started
normally, will show up on the top right corner of thermostat’ s screen.
succeed
failed
2. System Installation

（1-2）Add thermostat by scanning it's QR code or typing MAC ID manually.
（1-3）Pairing process between thermostat and gateway might take about 1 minute. Once
thermostat is paired with gateway successfully, will show up on the top right corner
of thermostat’s screen; App. interface also show up the added thermostat’s information.
10
2. System Installation 11 2. System Installation
2 Manually paring thermostat with gateway
（2-1）Preparation: Powered gateway correctly by plug-in socket, the LED on gateway
will be blinking rapidly (LED blinking rapidly means no connection between gateway and
server).
（2-2）Start gateway’s pairing mode by hold pressing until its LED is blinking slowly.
（2-3）Thermostat send pairing command with gateway.

（2-3-1）Long press to enter Menu Selection, when are flashing,
press to enter RF pairing interface.
（2-3-2）On RF pairing interface, select by pressing on or until flashing
show up on screen’s left side, press to send thermostat’s paring commend
to gateway; pairing success if flashing on screen’s right side, pairing failed if E01
or E02 is flashing on screen’s right side, in this case, you need to send the paring
command with gateway by pressing once again until pairing success.
868MHz is E11 error and 433MHz is E01 error.
succeed
failed
（2-4）Gateway is still under paring mode even one thermostat's paring succeed, if you
had more thermostats need to be paired, you may continue to pair them with gateway
manually. (1 gateway could RF communicate with 10 thermostats at one time).
（2-5）Exit pairing mode by hold-pressing until the LED recover to its status before
pairing.
（2-6）Once thermostat and gateway was paired successfully, their RF communication
started normally, will show up on the top right corner of thermostat’s screen; App.
interface also show up the added thermostat’s information.
12
2. System Installation 13 2. System Installation

14
2. System Installation 15 2. System Installation
2.3.2 RF communication test
To make sure RF communication between thermostat and receiver, thermostat and
gateway before using them regularly, you should take a RF communication test.
1 RF communication test between thermostat and receiver
Enter RF Communication Test by long pressing , when show up on screen’s
left side, presse to test RF communication between thermostat and receiver; test
result is good if show up on screen’s right side, otherwise, will show
up on screen’s right side, in this case, you need relocate the thermostat and do the test
once again.
2 RF communication test between thermostat and gateway
Enter RF Communication Test by long pressing , when show up on screen’s
left side, press to test RF communication between thermostat and gateway; test
result is good if show up on screen’s right side, otherwise, will show
up on screen’s right side, in this case, you need relocate the thermostat and do the test
once again.
good
bad
good bad

16 17
3. Operation Thermostat
1
there is a flashing , then enter Clock Setting by pressing .
Enter Menu Selection by long pressing , select by until
3.1 Clock Setting
Clock setting should be done if thermostat was used for the first time or after batteries
changed; automatically clocking setting will be done if thermostat was connected with
Internet via Gateway.
2
Area, press to select current year and press to set.
Firstly set Year after entered Clock Setting, when appeared on Temperat-ure
6 Back to the last setting menu by pressing .
4
date and press to set.
When appeared on Temperature Area, press to select current
5 When clock setting is flashing on Time Area, press to select current
time and press to confirm.
Hour Minute
3
month and press to set.
When appeared on Temperature Area, press to select current
3. Operation Thermostat

19
3. Operation Thermostat
18
3. Operation Thermostat
3.2.2 To adjust the pre-set program
1 Enter Program Setting by Pressing when is flashing.
Weekend’s pre-set program (Sat., Sun.)
Event
Time
Temperature
1
7
2
20
3456
21
7
7
00:00 7:00 9:00 12:00 14:00 16:30 23:00
18 21 18
Program Setting menu
This thermostat comes with the following default settings pre-programed for your
convenience:
3.2.1 Pre-set Program
Working days’ pre-set program
Event
Time
Temperature
1
00:00
7
2
6:30
20
3
8:30
16
4
12:00
16
5
14:00
16
6
16:30
21
7
22:30
7
3.2 Program Setting
3
temperature, press to confirm.
Temperature flashing in Temperature Area, press to adjust required
7 Days Program 1 Day Program
5+2 Days Program
2
press to confirm.
Enter 5+2 days/7 days/1 day program when Days flashing, select by ;

20 21
3. Operation Thermostat 3. Operation Thermostat
3.3 Override Mode-to change temperature for a
short period under AUTO mode
1
appeared on upper right.
Under AUTO mode, enter Override mode by pressing or ,
4 Time flashing in Time Area, press to adjust the 1st time as required,
press to confirm.
5 st Once the temperature and 1 time has been set, temperature flashing in Temperature
Area again, then you repeat to set the next temperature and time periods, as above steps
showing (checking from Step 3).
6 To cancel the program by pressing , go back to Menu Selection by keeping
pressing.
7
select target day by pressing , long press to confirm and paste.
Long press can copy current flashing day’s program setting to other day;
3 Exit Override Mode until next change in the preset program.
2
override temperature after flashing for 7 sec. or pressing , then continue to show
current temp-erature.
Adjust requ ired temperature by pressing or , confirm the

22 23
3. Operation Thermostat 3. Operation Thermostat
3.5 Holiday Mode
Make a holiday plan, it will keep your room at the pre-set temperature until your return time
is coming. The default temperature for Holiday Mode is 7℃, you also can change this
default value in User Options.
3.4 Manual Mode-to set a constant room temperature manually
1 Switch between AUTO and Manual Mode by pressing .
3 Adjust required temperature by pressing or , confirm after
flashing for 7 sec. or pressing , then continue to show current temperature.
2
Figure as following.
Under Manual mode, appeared on upper right and temperature flashing.
1 Enter Holiday Mode by keep pressing until showing on upper right.
2 Pre-set date and time for holiday start and return.
Month Date
★
by pressing .
Holiday start date: adjust by pressing as following figure, confirm

24 25
3. Operation Thermostat 3. Operation Thermostat
Under OFF Mode, your room’s Frost Protection will be automatically turned on unless you
exit the mode; The default temperature is 7℃, you can change this default value in User
Options.
3.7 OFF Mode (Frost Protection)
3.8 Child Lock
To avoid wrong operation by child, this thermostat has Child Lock function; once started
this function, there will be no reaction if short press on any button.
1 Enter OFF Mode by long pressing ,
following is the figure:
3 Holiday Mode will start automatically when holiday start time is coming, otherwise, it
continue AUTO Mode.
4 To cancel Holiday Mode’s setting by keep pressing.
It is an quick access to energy saving but also maintain comfort. Under ECO Mode, the
room will be always kept at a pre-set temperature unless you exit this mode. The default
temperature is 9℃, you can change this default value in User Options.
1 Enter ECO mode by pressing ,
following is the figure:
3.6 ECO Mode
2 Exit ECO mode by pressing .
2 Exit OFF Mode by pressing .
1
select by , confirm by pressing
to open Child Lock function when is
flashing.
Long press to enter Menu Selection,
2 Cancel Child Mode by long pres .
★Holiday start time: adjust by pressing
as following figure, confirm by pressing
.
Hour
★
Return date and time’s pre-set: once Holiday Start’s date and time has been set, start
to set return date and time in the same way.
Minute

26 27
1. You may change user operation after entered User Operation by Pressing
when is flashing under Menu Selection.
2. Under User Option, the option ID is showing on Temperature Area(screen left side), the
Option Content is shown on Time Area(screen right side).
4. User Option
4. To cancel User Operation’s setting, press when Option Content flashing.
5. User Options Table
3.
t o scroll through selectable options, select the target Option ID by
pressing ; then, adjust the User Option by pressing and set it
down by pressing .
Option ID is flashing under User Option(details to see User Options Table below), press
5. To exit User Operation’s setting, press when Option ID flashing
24
1
ON
0
12
1
OFF
-10
24
3
ON
10
ID
1
2
3
4
Min. Max. Default Option Content
Change 12h or 24h clock
Change to another pre-set
program
Switch on/off summer/winter time
Change temperature offset
(0.5°C / step)
°C
OFFOFF ON
5Restore the factory Settings
OFF
ON
OFF
OFF
ON
ON
6
7
To disable Off function
Frost Protection
00
OFF
5
ON
C F C
11
12
5
32
9
5
5
5
32
32
32
8
9
10
13
14 -30 30 0
15 OFF ON OFF
Pre-set the lowest temperature
Pre-set the highest temperature
Pre-set the ECO temperature
Valve Protection(unit: min., if the
valve has not been opened for
24hours, it will be automatically
opened every 10:00am; “0”
means no Valve Protection
Activate Smart Remote
Control (App remote control)
Change degrees Celsius
or Fahrenheit
Change humidity
PID control function
OFF ON for
Wi-Fi thermosta)
(

28 29
6. Product Specification 6. Product Specification
17 3 0.3（+/- °C）
16
110
110 3 0.3（+/- °C）
PID control hysteresis adjustment
Temperature control hysteresis
adjustment
18
19
20
OFF
60（minute）
5°C
OFF
0
Id8
ON
60
Id9
Window opening function
Window opening stop heating time
OFF mode target temperature
range setting
Wireless Receiver
Operating Temperature
Transmitting frequency
Communication Range
(open space)
Power
Power supply
Switch rating
0 to 50°C
868 MHz(433 MHz-PTR16-433)
Bidirectional
,
100 meters
<2W
100VAC~240VAC, 50Hz
240VAC 50Hz, Max.16A
Dimensions (HxWxD)
IP class
Standard
Weight
100x 85 x 32mm
IP30
CE
150g
Wireless Programmable Thermostat
Operating Temperature
Control mode
0 to 50°C
Heating system
Display
Transmitting frequency
Communication Range
(open space)
LCD with backlight
868 MHz(433 MHz-PTC10-433),
2 way
100 meters
Power supply
Battery life
Temperature setting range
Temperature control accuracy
Measurement interval
Frost protection temperature
2 x AA alkaline batteries
Typically 2 years
5°C to 32°C (0.5°C step)
+/-0.3°C
every minute
5°C
Humidity range 10 to 90%RH
Humidity accuracy
Time display
Dimensions(HxWxD)
IP class
Standard
Weight
12 hour/24 hour
117.2 x 87.2 x 26.6mm
IP30
CE
211g with battery
+/-5%RH
Warning: User option 19, 20 substantial reduction in sensitivity may lead to
frequent on and off heating, especially when using automatic PID control, in the
worst case it may damage the heat source.