PoeWit MD-1 User manual

poewit.com
CLOUD INTELLIGENT
OUTDOOR DUAL MOTION AND LIGHT SENSOR
POWERED BY POE+
QUICK START GUIDE
MD-1 MODEL

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
1
BEFORE YOU START
1) PACKAGE CONTENTS
Confirm that you have the package contents as follows:
1. PoE powered motion detector and light sensor
2. Lens shield label
2) PRODUCT DESCRIPTION
PoEWit PoE powered passive infrared motion detector and light
sensor can be mounted on either a wall or ceiling. It is waterproof
and can automatically motion trigger PoEWit lighting hardware
through cloud connectivity.
OS-458/A
PA SS IVE INF RA -RED SE NS OR
FO R AU TO MA TION CO NT RO L
Outdoor Motion Detector
For PoEWit Control System
MD -1
PATTERN
ITEM
QUANTITY
Motion
detector/light
sensor
1
Lens shield
label Quick start
1 1

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
2
The MD-1 can be configured to trigger as many PoEWit lighting
hardware as desired. The MD-1 is IOS and andriod app controlled;
the user can adjust lux, time and sensitivity through the app.
- Unique construction design for enabling wall mount and
ceiling mount.
- The detector head can be adjusted 90° up / 40° down / 90°
left / 90° right for detecting angle adjustment.
- A photocell is built-in to allow automatically switching on/off
the light as per the preset lux value.
- Meet IP65 protection level.
• Dimensions:
- Wall mount: 162.3 x 98 x 111.4mm (6.3 x 3.85 x 4.38 inch)
66
98
162.3
98
111.4
Fig 1a

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
3
- Ceiling mount: 108 x 139.4 x 115.3mm (4.25 x 5.48 x 4.53 inch)
3) INSTALLATION AND WIRING
• Select a proper location.
• It can be installed at the height of 2 - 4m (6.5 - 13.12 feet). It is
recommended to install it at the height of 2m (6.5 feet) to gain
optimal detection pattern; the detection range can reach up to
12m (39.37 feet) at the height of 2m (6.5 feet). (See fig 1)
Fig 1b
Ceiling mount: 108 x 139.4 x 115.3mm
FIG.1-B
95.40
108
2.2 Dimension (See FIG.1-A & FIG.1-B)
Wall mount: 162.3 x 98 x 111.4mm
FIG.1-A
66
98
162.3
98
111.4
115.3
95.3 139.4

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
4
• Helpful tips for installation
- The optimal installation location can be both indoor or
outdoor; garden, corridor, staircase, entrance, garage, public
lavatory, outdoor parking area, household and office, etc.
O
180
6m
6m
12m
12m1.50
1.5
Top view Side view
2m
1.5
Fig 2

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
5
- Since the detector responds to temperature change,
please avoid the following conditions:
1) Avoid pointing the detector towards the objects whose
surfaces are highly reflective, such as mirror, swimming
pool, etc.
2) Avoid mounting the detector near heat sources, such
as heating vents, air conditioners, lights, etc.
3) Avoid aiming the detector towards objects which
may be swayed by wind, such as curtain, tall plants, etc
OPEN
OPEN
Fig 3

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
6
- Pay attention to the walking direction on the test
proceeding (see fig 4)
Fig 4
More sensitive to movement
across the detector
Less sensitive to movement
directly towards the detector

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
7
4) INSTALLATION PROCEDURE
• MD-1 can be mounted either on the wall or ceiling.
• Feed the ethernet cable through the rubber gasket (Will need
to terminate the RJ45 jack AFTER feeding the Cat5 cable
through the rubber gasket), then mount the bottom cover on the
wall or ceiling using the two screws (see fig 5 and 6)
Fig 5
RJ45 plug
Fig 6
Watertight screw

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
8
• Fix the detector head to the bottom cover and adjust the
  detectorheadtobeintherightposition(seeg7a&7b)
• Detector head can be adjusted downward to max. 40° and
  upwardtomax.90°vertically(seeg8a)toshortenthedetection
range, or turned leftward and rightward max 90° horizontally
(see fig 8b). Please adjust detector head to get the desired
detection field.
Fig 7bFig 7a
Wall Mount Ceiling Mount

poewit.com
OUTDOOR POE DUAL MOTION AND LIGHT SENSOR MD-1 | QUICK START
9
5) USAGE OF LENS SHIELD LABEL
The attached lens shield label can be used to change the detection
coverage. With the different layers of labels used, the different
coverage can be obtained (see fig 9)
Fig 8a Fig 8b
O
90
O
40
O
90 O 90
O
30
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10 11 12
O
50
1 2 3 4 5 6 7 8 9 10 11 12
O
80
O
100
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10 11 12
O
180
O
150
1 2 3 4 5 6 7 8 9 10 11 12
Fig 9