PoeWit NS-24 User manual

poewit.com
Network Switch
24 | 48 Port - 370 | 740 Watts
CLOUD INTELLIGENT
L3 Perpetual PoE+
QUICK START GUIDE
NS-24 / NS-48 MODELS

poewit.com
INSTALLATION AND SETUP
1
BEFORE YOU START
Depending on your hardware model, your switch may appear dierent
than the figures shown in this guide.
1) INSTALLATION AND SETUP
Conrm that you have the tools and package contents as follows:
Tools Required:
• Phillips #2 screwdriver
Package Contents:
1. Ethernet Switch NS-24/48, console cable, power cord, rack-mounting
hardware that includes:
• Rack-mount brackets (2)
• Screws to attach brackets to the switch (8)
PATTERN
ITEM
QUANTITY 1
Quick start
1
PoE Powered LED
Flood Light
OS-1-PT-X
PATTERN
ITEM
QUANTITY
Ethernet Switch
NS-24/48
1
Rack Mounting
Hardware

poewit.com
INSTALLATION AND SETUP
2
2) PRODUCT DESCRIPTION
The NS-24 and NS-48 provide the highest power supply in their
class with an industry-leading 370 Watts and 740 watts respectively.
Also, these PoE switches are designed with perpetual PoE which,
allows the user the option to preserve power to any PoE connected
devices during warm reboots.
Note: Be sure to order Direct Attach cables and SFP or SFP+
transceivers if required.
2A) UNPACK EQUIPMENT
1. Unpack the ethernet switch NS-24/48 Series.
2. Observe ESD precautions when unpacking.
2B) PREPARE THE RACK (OPTIONAL)
1. Provide the equivalent of 1U of vertical rack space for each NS-24
or NS-48 model in an EIA or IEC-standard 19-inch
(48.2-centimeter) equipment rack.
2. Ensure that the equipment rack is stable and securely attached
to a permanent structure.
3. Ground the rack to the same grounding electrode used by the
power service in the area. The ground path must be permanent

poewit.com
INSTALLATION AND SETUP
3
and must not exceed 1 Ohm of resistance from the rack to the
grounding electrode.
2C) INSTALL THE SWITCH
When you install the switch in the network, ensure you use the
following cables:
1. Category 5E or higher specification cabling should be used for
one Gbps/1000 Mbps operation
2. Multimode or single mode fiber cable depending on the
transceiver type. For 850nm transceiver uses multimode fiber
cable. For 1310 nm transceiver uses single mode ber cable instead.
3) RACK MOUNTING
1. Attach a bracket to each side of the switch
Fig 1

poewit.com
INSTALLATION AND SETUP
4
2. Slide the switch into the rack. Insert and tighten the rack-mount screws.
3. Verify that the switch is securely fastened to the rack.
4) CONNECTION TO NETWORK AND POWERING UP
Connect port 1 on the switch to a router.
NOTE: Port 1 is a dedicated Cloud uplink port and must be used to
connect to the router if VLAN’s are used. Port 1 cannot be added
to any VLAN’s.vvv
Fig 2
Fig 3

poewit.com
INSTALLATION AND SETUP
5
Warning: You must use a power cord set approved for the NS-
24/48 Series switch and the power receptacle type for your
country.
5) CONFIGURATION INSTRUCTIONS
Power up the device and you should be automatically connected
to the Internet. You are now ready to download and install our App.
You can search Poewit in the Apple App Store or Google Play to
get the App.
NOTE: Your device and mobile phone both must have an Internet
connection through the same external IP address and must be
on the same local subnet.
6) Warranty information
For warranty information please check our support page on our
website.
Please read these operating instructions carefully before start
of operation.

poewit.com
INSTALLATION AND SETUP
6
© 2020 PoEWit Technologies
Suitable for installation in Information Technology Rooms in
accordance with Article 645 of the National Electrical Code
and NFPA 75.
“Peut être installé dans des salles de matériel de traitement de
l’information conformément à l’article 645 du National Electrical
Code et à la NFPA 75”
“Equipment is intended for installation in Restricted Access
Location” (Instruction)
“Les matériels sont destinés à être installés dans des
EMPLACEMENTS À ACCÈS RESTREINT” (Instruction) The device
can only be used in a xed location such as a telecommunication
centre, a dedicated computer room. When you install the device,
ensure that the protective earthing connection of the socket-
outlet is veried by a skilled person.
Class I Equipment. This equipment must be earthed. The
power plug must be connected to a properly wired earth
ground socket outlet. An improperly wired socket outlet could
place hazardous voltages on accessible metal parts.
The installation instructions clearly state that the ITE is to be
connected only to PoE networks without routing to the outside
plant.
Caution: The Optical Transceiver product should use UL
listed, and Rated Laser Class I, 3.3 Vdc