Polk Audio MM1 MM522 User manual

OWNER’S MANUAL
MM522, MM572, MM652, MM692, MM6502

WIRING DIAGRAMS
Figure 1
Basic coaxial connection
Amplifier
Coaxial Speaker
Figure 2
Basic component connection installing MM6502
Mid-Woofer
Crossover
Tweeter
Amplifier
MOUNTING DIAGRAMS
Figure 3
Crossover mounting allows for proper ventilation. Tweeter
Attenuation Switch located outside crossover box, move to desired
tweeter level setting.
Figure 4
Installing MM522, MM652, MM692, & MM6502 models with grille
Figure 5
Installing MM572 oval models
Figure 4
Figure 5
ONLINE MANUAL
Tweeter Attenuation Switch
Figure 3
Figure 1
Figure 2

ONLINE MANUAL
Figure 6
Flush mount tweeter mounting
1. Check for proper clearance: The flush mount kit is 1” (26mm) deep.
2. Mark the center of the spot and cut a 2” (50.8mm) diameter hole
using a hole saw, drill bit or razor knife.
3. Assemble the cup, clamp and machine screw loosely as shown.
4. Route wires through the round opening in the bottom of the cup.
5. Press the assembly into the 2” (50.8mm) diameter hole until the clamp edge
is below the mounting surface, then tighten the screw. The legs of the clamp
can be bent outward by inserting a screwdriver through the holes in the cup
while still mounted.
6. Connect wires from the tweeter terminals of the Crossover to the tweeter
itself using the faston connectors. Connect the red wire from the (+) terminal
of the Crossover tweeter output to the red (+) wire from the tweeter.
7. Mount the tweeter by snapping it into the mounting cup.
Figure 6

Figure 7
Surface mount tweeter mounting
1. Using the base of the surface mount cup as a template, mark the screw
hole and drill them using a 1/8” (3mm) drill bit. Drill a second hole
(for the speaker wire) using a 3/16” (5mm) drill bit.
2. Screw surface mount cup to the panel.
3. Push the tweeter wires through the open area at the bottom of the cup
and through the 3/16” (5mm) hole in the panel.
4. Connect wires from the tweeter terminals of the Crossover to the tweeter
wires using fast on connectors. Be sure to connect the red wire strand
from the tweeter to the (+) terminal of the crossover tweeter output.
5. Mount the tweeter by snapping it into the mounting cup.
ONLINE MANUAL
Figure 7

MM1 Series Coaxial and Component Systems Specifications
MM522 MM572 MM652 MM692 MM6502
Type 5.25˝
Coaxial
5˝x 7˝
Coaxial
6.5˝
Coaxial
6˝x 9˝
Three Way
6.5˝
Component System
Driver Complement (inches & mm) 5.25˝
133.35 mm
5˝x 7˝
127 mm x 177.8 mm
6.5˝
165.2 mm
6˝x 9˝
152.4 mm x 228.6 mm
6.5˝
165.2 mm
Tweeter Complement (inches & mm) 1˝
25 mm
1˝
25 mm
1˝
25 mm
1˝+ 3/4˝
25 mm + 19 mm
1˝
25 mm
Cutout Dimensions (inches & mm) 4.61˝
117 mm
4.92˝x 7.15˝
125 mm x 181.6 mm
5˝
127 mm
5.63˝x 8.42˝
143 mm x 213.8 mm
5˝
127 mm
Mounting Height (inches & mm) 0.20˝
5.07 mm
0.25˝
6.35 mm
0.32˝
8.07 mm
0.30˝
7.60 mm
0.32˝
8.07 mm
Mounting Depth: Top (inches & mm) 2.37˝
60.1 mm
2.56˝
65 mm
2.62˝
66.5 mm
3.07˝
78 mm
2.62˝
66.5 mm
Mounting Depth: Bottom (inches & mm) 2.57˝
65.2 mm
2.82˝
71.5 mm
2.86˝
72.6 mm
3.38˝
85.8 mm
2.86˝
72.6 mm
Peak Power Handling 240 W 300 W 300 W 450 W 375 W
Continuous Power Handling 80 W 100 W 100 W 150 W 125 W
Nominal Impedance (ohm) 4 4 4 4 4
Frequency Response (Hz) 50Hz-40kHz 35Hz-40kHz 40Hz-40kHz 30Hz-40kHz 35Hz-40kHz
Grille Height 0.92˝
23.3 mm N/A 0.95˝
24.2 mm
1.03˝
26.2 mm
0.95˝
24.2 mm
Sensitivity (dB) 92 93 93 94 93
Learn more about GPS navigationon our website.