Polycom 55" LED DISPLAY User manual

55” LED DISPLAY

Codec
Connecting an External Amplifier
11
11
Connecting an External Amplified Speaker
On Screen Status Display
Special Notices
11
14
15
14
16
16
Fine Tuning Under RGB/HDMI Mode
Specifications
Dimensional Drawings
18
18
19
23
25
26
25
Supported Resolutions
Explanation of Various Picture Control Settings
Command Format and Sequencing
Explanation of Various System Settings
Timing For Component
RJ-45 Connection
13
14
16
20
23
02
02

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
Upon completion of service or maintenance, request the service technician to perform safety check to ensure
03
03
AVERTISSEMENT : Pour réduire le risque de choc électrique, ne pas retirer les
couvercles avant ou arrière. Aucune pièce n'est réparable par l'utilisateur. Confiez
l'entretien à du personnel qualifié.
Risk of Electric Shock. Do Not Open!
Risque de choc électrique. Ne pas ouvrir!
WARNING / ATTENTION
WARNING : To reduce the risk of electric shock, do not remove the front or back covers.
No user-serviceable parts inside. Refer servicing to qualified service personnel only.

Cleaning & Maintenance
Disconnect from the electric outlet before cleaning. Do not use liquid or aerosol cleaners. Use only
a slightly damp cloth for cleaning.
Regulatory Notice
CE Statement
The CE label on this product indicates that it complies with the 89/336/EEC directive on
electromagnetic compatibility and safety rules as defined in the 73/23/EEC, low voltage directives.
This product is protected against interferences from other electronic devices, provided that these
devices comply with the standards in force. Sporadic interferences may happen nevertheless.
FCC Statement
The Federal Communications Commission Radio Frequency Interference Statement includes
t he follow ing warning :
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television receptions, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures :
Reorient or relocate the receiving antenna.
Increase the separat ion bet ween the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult t he dealer or an experienced radio/display technician for help.
Disconnect the unit from the main supply and refer servicing to qualified service personnel under
the following conditions :
Power cord or plug is damaged or frayed.
Liquid has been spilled into the product and/or the unit has been exposed to water or moisture.
Unit does not operate normally when the operating instrucions are not followed. Adjust only those
controls that are covered by the operating instructions, improper adjustment of other controls may
result in damage which often requires extensive work by a qualified technician to restore the unit
to normal operation.
Unit has been dropped or the cabinet has been damaged.
Unit exhibits a distinct change in performance, indicating a need for service.
Users must use the mounting device and means provided specifically for the apparatus, or UL listed
wall mount bracket, to mount it, or the equivalent.
04

05

06
Checking the Accessories Supplied
LED Display Remote Control
with Batteries User’s Manual
Front Panel Controls
Status LED
Orange-Standby
The LED will illuminate in orange color if
the display is at standby mode and the
main power cord is plugged into the back
of the unit.
Solid Green-Power on
Power(Standby) Button
Turns power on from standby mode.
There is a wait period between
on/standby cycles.
Adjustment Buttons
Select Buttons
Use these buttons to navigate through the On
Screen Display menu.
Menu Button
Use this button to engage the On Screen
Display menu.
Input Button
Use this button to switch between available
inputs.
Battery Installation
13
2
4
5
6
1 3 4 5
26
55” LED DISPLAY
イインチチデディィスププレ
55
ン
LED
ス レ
イイ
디디스스플플레레이이
55” LED
СД-ТЕЛЕВИЗОР С
Д
ИАГОНАЛЬЮ 55"
MONITOR LED 55”
55
吋吋
LED
顯顯示示器器
55
吋吋
LED
显显示示器器
These keys serve as navigation and
adjustment keys when On Screen Display
menu is engaged.
Overview

a Codec or PC video connector.
*The USB port is labelled. It is provided for after
service/engineer use ONLY.
RJ-45
07

08

After changing settings on the OSD menu, the new settings are confirmed automatically
shows detailed information regarding the operation status of
when OSD picture vanishes.
To access the OSD menu, press “MENU”
button on the remote control or on the
rear cover.
Navigation through the OSD menu
can be accomplished by using the
“Left/Right” or “Up/Down” keys on
remote control or rear cover.
OSD Menu
Navigation OSD Menu
Access
1
2
1
09

10