POLYGROUP LIMITED SUMMER WAVES SKIMMERPLUS SFX600 User manual

Should you encounter a problem with your Polygroup® Product, please DO NOT return the product to the place of purchase. All Warranty claims must be made
directly to Polygroup®. Prior to contacting Customer Service, please first review the Troubleshooting Guide in the Installation Manual, or review the FAQ and
instructional videos at support.polygroupstore.com. If you are still unable to correct the problem, please contact Polygroup® Customer Service at [phone]. Please
have the product type, model number and your purchase receipt ready, so that our Customer Service Representative can assist you in resolving the problem. You may
be asked to return all or part of the product for inspection and/or repair. Do not return any product to Polygroup® without a Return Merchandise Authorization number.
For answers to common questions, setup videos and troubleshooting tips, please visit
support.polygroupstore.com or call Customer Service: [phone]
DO NOT RETURN PRODUCT TO STORE
To order parts and accessories,
please visit www.polygroupstore.com
READ AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
SUMMER WAVES®
SKIMMERPLUS® FILTER PUMP
FOR ABOVE GROUND SWIMMING POOLS
SFX600 / SFX1000 / SFX1500 models
DISTRIBUTED BY: POLYGROUP® LIMITED (MACAO COMMERCIAL OFFSHORE)
Unit J, 10th Floor, Macau Square, Av do Infante D.Henrique, No.43-53A, Macau
OWNER’S MANUAL
Manual #
09C3A40USA17
LIMITED WARRANTY
Polygroup® Limited (Macao Commercial Offshore), (hereinafter “Polygroup®”) warrants to the original purchaser only, the SFX type Electric Filter Pump against defects
in material and workmanship for 180 days from the date of purchase. Original Purchaser must retain proof of such purchase in the form of an original store sales
receipt and must produce such upon request by Polygroup® or its designated agents. Warranty claims cannot be processed without a valid proof of purchase.
This Limited Warranty applies only to the original purchaser of the product and is limited solely to the repair or replacement of the product, to be decided in Polygroup®’s
sole discretion. Consequential damages, including claims for loss of water, pool chemicals, damage, or labor are not covered under this Limited Warranty. This Warranty
will be declared invalid should the Purchaser modify or repair the product themselves or by unauthorized persons; use non-Polygroup® parts or accessories with the
product; use the product in contravention of the manufacturer’s Instructions; use improper voltage; abuse the product in any way; or through accident or negligence.
Normal wear-and-tear is not covered under this Warranty, nor are acts of God outside the control of Polygroup®. Polygroup® will not be held responsible for
grasses that may grow through the ground cloth and/or pool liner, as this is not a manufacturing defect.
IN NO EVENT SHALL Polygroup®, THEIR AUTHORIZED AGENTS, RELATED ENTITIES, OR EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER
PARTY FOR DIRECT OR CONSEQUENTIAL DAMAGES. Some states or countries, or others jurisdictions, do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.

Warnings........................................................................................................................................................
Preliminary Steps & Filter Pump Important Notes & Filter Pump Power Information & Parts List.........................
Setup Instructions & Filter Pump Operation...................................................................................................
Pump Motor Protection & Filter Cartridge Cleaning and Replacement & Pool Maintenance.........................
Pool Water Care.............................................................................................................................................
Troubleshooting Guide & Pool Pump Disassembly and Storage...................................................................
Pump Removal Instructions for Troubleshooting...........................................................................................
Rotor Inspection and Replacement Instructions............................................................................................
Pump Replacement Instructions....................................................................................................................
Replacement Parts Ordering Information.......................................................................................................
3 ~6
7 ~8
9 ~ 10
11
12
13
14
15
17
TABLE OF CONTENTS
2
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
16

IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following :
READ AND FOLLOW ALL INSTRUCTIONS
Keep for Future Reference. Failure to follow these warnings and instructions can result in serious injury or death to users, especially children
NOTICE: CUSTOMERS THAT PURCHASE POOLS MAY BE REQUIRED BY LOCAL OR STATE LAW TO INCUR ADDITIONAL EXPENSES WHEN
INSTALLING A POOL, IN ORDER TO COMPLY WITH STATE OR LOCAL LAWS REGARDING FENCING AND OTHER SAFETY REQUIREMENTS.
CUSTOMERS SHOULD CONTACT THEIR LOCAL BUILDING CODE ENFORCEMENT OFFICE FOR FURTHER DETAILS. POLYGROUP® IS NOT
RESPONSIBLE FOR ANY ADDITIONAL EXPENSES THAT YOU MAY INCUR.
Safety Care for Children
1. Children, especially children younger than five years, are at high risk of drowning. Drowning occurs silently and quickly and can occur in as little as 2 in. (5 cm) of water.
2. Keep children in your direct sight, stay close, and actively supervise them when they are in or near this pool and when you are filling and emptying this pool.
3. When searching for a missing child, check the pool first, even if the child is thought to be in the house.
4. Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool.
5. WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Swimming Pool Barriers
Very Important: Swimming pool barriers, which restrict access to the pool by small children, may be required by law. A barrier is necessary to provide protection against
potential drowning and near drowning. Barriers are not a substitute for constant supervision of children. Check state or local laws and codes before setting up pool.
Swimming Pool Equipment
1. The use of artificial pool lighting is at the discretion of the pool owner. Lighting, when installed, should be in accordance with Article 680 of the
National Electrical Code (NEC) or its latest approved edition and in consultation with a licensed electrical professional.
2. Keep all electrical lines, radios, speakers and other electrical appliances away from the pool.
3. Do not place pool near or under overhead electrical lines.
4. All electrical components installed in and/ or adjacent to an aboveground/onground residential swimming pool shall be installed in accordance with and shall comply
with the requirements of the latest published edition of NFPA 70, National Electrical Code (NEC®) Article 680, Swimming pools, fountains, and similar installations,
and any state or local code.
Filter Pump Awareness
1. WARNING: Risk of Electric Shock. Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug or cord is needed, use only identical replacement parts.
2. WARNING: To reduce the risk of electric shock, replace damaged cord immediately.
3. WARNING: To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
4. CAUTION: To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances
closer than 5 feet (1.5 m) from the pool.
5. CAUTION: This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being
readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it
cannot be readily disassembled for storage.
OWNER’S MANUAL
3
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
WARNING
DO NOT SIT ON
OR LAY OVER
POOL WALL
YOU CAN BE PERMANENTLY
INJURED.
WARNING
AVOID ENTRAPMENT!
STAY AWAY FROM DRAINS & SUCTION
FITTINGS.
YOUR HAIR, BODY & JEWELRY
CAN GET SUCKED INTO DRAIN.
YOU COULD
BE HELD UNDER WATER & DROWN. DO NOT
USE POOL IF DRAIN OR SUCTION OUTLET
COVER IS MISSING OR BROKEN.
DANGER
PREVENT DROWNING!
CLOSELY WATCH CHILDREN WHO
ARE IN OR NEAR THIS POOL. CHILDREN
UNDER 5 ARE AT HIGHEST RISK FOR
DROWNING. EMPTY POOL OR PREVENT
ACCESS WHEN NOT IN USE.
NO DIVING!
SHALLOW WATER
YOU CAN BREAK
YOUR NECK AND BE
PARALYZED.

6. CAUTION: For continued protection against possible electric shock this unit is to be mounted to the base in accordance with the installation instructions.
7. Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
8. The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button.
Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by
a qualified service representative before using.
9. The Filter Pump is to be assembled by an adult; care should be taken in the unpacking and assembly of the Filter Pump, this pool may contain accessible
potentially hazardous sharp edges or sharp points that are a necessary part of the function of the Filter Pump.
10. If a drain or suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration,
or drowning. Repair or replace the drain or suction outlet cover before allowing the pool to be used.. During nighttime pool use, artificial lighting shall be used to
illuminate all safety signs, ladders, steps, deck surfaces and walks.
11. The floor of the pool shall be visible at all times from the outside perimeter of the pool.
12. Post a list of emergency telephone numbers such as the nearest available police, fire, ambulance and/or rescue unit. These numbers are to be kept near the
telephone, which is closest to the pool.
13. Basic lifesaving equipment, including one of the following should be on hand at all times:
• A light, strong, rigid pole (shepherds crook) not less than twelve feet (12’) [366 cm] long.
• A minimum one-fourth inch (1/4”) [6.35 mm] diameter rope as long as one and one half (1-1/2) times the maximum width of the pool or fifty feet (50’) [15.24 meters],
whichever is less, which has been firmly attached to a Coast Guard-approved ring buoy having an outside diameter of approximately fifteen inches (15”) [38.1 cm],
or similarly approved flotation device.
14. Pool shall be located at a minimum distance of 6 ft (1.83 m) from any receptacle, and all 125-volt 15- and 20-ampere receptacles located within 20 ft (6.0 m) of the
pool shall be protected by a ground fault circuit interrupter (GFCI), where distances are by measuring the shortest path the supply cord of an appliance connected
to the receptacle would follow, without piercing a floor, wall, ceiling, doorway with hinged or sliding door, window opening, or other effective permanent barrier, to
the inside wall of the pool.
Circulation Systems
1. Installers shall follow written instructions regarding positioning of all equipment connected to the circulation systems.
2. The installer shall follow written instruction provided for operation of the circulation system components.
3. All circulation system components and pumps that require replacement or servicing shall be installed according to the pump’s instruction manual.
4. Circulation equipment shall be installed per manufacturer’s instructions to provide proper mounting and support, to prevent damage from misalignment, settlement,
and vibration, and to minimize the potential for the accumulation of debris and moisture. Please refer to pump’s instruction manual.
Chemicals
For safety sake, ensure the deepest part of the pool is always visible. The user must properly maintain the clarity of the pool water at all times. Check the pH and
chlorine levels periodically and make sure they are within the recommended limits. Additional water treatment chemicals might be needed from time to time. Have
the water sample tested by a local pool supply store to determine if additional chemical is needed. Turn on the pump for the recommended hours daily. If you are
unsure of the time frames please refer to support.polygroupstore.com for the recommended Pump Operation Hours based on pool types and sizes. Clean
and replace filter cartridge frequently. Replace only with genuine Polygroup®/ Summer Wave® Brand filter cartridge. Refer to the Filter Pump
manual for additional water care information.
Entrapment Risk
1. Entrapment Avoidance: There shall be no protrusions or other obstruction in the swimming area, which may cause entrapment or entanglement of the user. If
a suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration, or drowning.
Repair or replace the suction outlet cover before allowing the pool to be used.
2. DANGER! TO AVOID SERIOUS INJURY OR DEATH, CLOSE THE POOL OR SPA TO BATHERS IF ANY SUCTION OUTLET COVER/GRATE IS MISSING,
BROKEN OR INOPERATIVE.
3. Never play or swim near drains or suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
4. Never enter the pool or spa if a suction fitting or drain cover is loose, broken, or missing.
5. Immediately notify the pool/spa owner or operator if you find a drain cover loose, broken or missing.
Drowning Risk
1. Keep unsupervised children from accessing the pool by installing fencing or other approved barrier around all sides of pool. State or local laws or codes may require
fencing or other approved barriers. Check state or local laws and codes before setting up pool.
2. Toys, chairs, tables or similar objects that a young child could climb shall be at least four feet (4’) [121.92 cm] from the pool. The pump filter system shall be positioned
so as to prevent it being used as a means of access to the pool by young children. Do not leave toys inside pool when finished using, since toys and similar items
might attract a child to the pool.
3. Position furniture (for example, tables, chairs) away from pool and so that children cannot climb on it to gain access to the pool.
Electrocution Risk
1. Keep all electrical lines, radios, speakers and other electrical appliances away from the pool.
2. Do not place pool near or under overhead electrical lines.
4
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.

First Aid
1. Keep a working phone and a list of emergency numbers near the pool.
2. Become certified in cardiopulmonary resuscitation (CPR). In the event of an emergency, immediate use of CPR can make a lifesaving difference.
Special Warning
1. Local building codes may require obtaining a building or electrical permit. Installer shall follow regulations on setback, barriers, devices and other conditions.
2. Safety signs shall comply with requirements of ANSI-Z535 and to use signal wording.
3. DO NOT attempt to assemble this pool in adverse weather conditions, windy conditions or when the temperature is below 60°F.
4. This is a storable filter pump, which should be disassembled and stored when temperatures are expected to fall below 32°F.
Extra Safety Warning
1. Adult supervision is always required.
2. Parents should learn CPR.
3. Keep all electrical radios, speakers and other appliances away from the swimming pool.
4. When you touch the filter, pump, or electrical parts, be sure the ground under your feet is “Bone Dry.”
5. All electrical outlets should have a GFCI and connections should be a minimum of 6 feet (1.83 m) from the outside perimeter of the wall of the pool.
From 6–10 feet (1.83–3.05 m), there should be either a fixed connection (outlet box) or twistlock connection with a GFCI.
6. Connect power cords to a 3-wire grounding-type outlet only.
7. Keep all breakable objects out of the pool area.
8. Alcohol consumption and pool activities do not mix. Never allow anyone to swim, dive or slide while under the influence of alcohol or drugs.
9. Severe electrical shock could result if you install your pump or filter on a deck. The pump or filter could fall into the water, causing severe shock or electrocution.
10. Do not install on a deck or other surface at, above, or slightly below the top rail of the pool.
11. Do not use the filter pump during severe weather conditions, i.e. electrical storms, tornadoes, etc.
12. Be aware of overhead power lines when vacuuming your pool or using a telescoping pole.
13. Check regularly for signs of wear that could make the pool unsafe.
14. Please contact pool site dealer or manufacturer for additional safety signs if deemed necessary.
15. For pool service, select a certified pool professional.
For additional safety information, see www.APSP.org.
Consumer Awareness Booklets and Information Source
Contact: U.S. Consumer Product Safety Commission at www.CPSC.gov/cpscpub/pubs/pool/pdf, Pub. #362 “Safety Barrier Guidelines for Home Pools”.
1. The Sensible Way to Enjoy Your Aboveground/Onground Swimming Pool
2. Children Aren’t Waterproof
3. Layers of Protection
4. Pool and Spa Emergency Procedures for Infants and Children
5. Be Safety Aware Copies of the above brochures are available free from the APSP. Go to: www.APSP.org.
Safety Education Programs and Materials Educational programs and materials (i.e., seminars, workshops, brochures, videos, instructional guides) are available from
the APSP, other aquatic safety groups, and by private firms. As a means of communicating useful safety information to pool owners/operators, and users, industry
members are permitted to provide such information to owners/operators and to request or require owners/operators to sign a statement that they have received, read,
and will follow the guidelines.
Other sources of safety information:
• www.cdc.gov
• www.cpsc.gov
• www.drowningpreventionalliance.com
• www.nspf.org
• www.safekids.org
ANSI American National Standards Institute
25 West 43rd Street, New York NY 10036
Contact: 212-642-4900
www.ansi.org
APSP Association of Pool & Spa Professionals
(formerly National Spa and Pool Institute)
2111 Eisenhower Avenue, Suite 500
Alexandria VA 22314-4679
Contact: 703-838-0083
www.apsp.org
OWNER’S MANUAL
5
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.

6
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
ASME American Society of Mechanical Engineers
Two Park Avenue, New York NY 10016-5990
Contact: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America)
www.asme.org
NSPI National Spa and Pool Institute (see APSP)
UL Underwriters Laboratories
333 Pfingsten Road, Northbrook IL 60062-2096
Contact: 877-854-3577 or 847-272-8800
www.ul.com
NSF NSF International
P.O. Box 130140
789 N. Dixboro Road
Ann Arbor MI 48105
Contact: 800-673-6275 or 734-769-8010
www.nsf.org
ASTM ASTM International (formerly American Society of Testing & Materials)
100 Barr Harbor Drive, P.O. BOX C700
West Conshohocken, PA 19428-2959
Contact: 877-909-2786 (USA & Canada) or 610-832-9585 (International)
www.astm.org
NEC National Electrical Code (see NFPA)
NFPA National Fire Protection Association
1 Batterymarch Park, Quincy MA 02169-7471
Contact: 800-344-3555 (U.S. & Canada) or 617-770-3000 (International)
www.nfpa.org
Filtration Systems
Any equipment connected to the circulation systems shall be positioned so as to prevent their being used as a means of access to the pool by young children. (See the
latest published edition of ANSI/ APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Barrier
Barriers are necessary to provide protection against potential drowning and near drowning and that barriers are not a substitute for the constant supervision of
children. (See latest published edition of ANSI/APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Risk of Drowning, Entrapment, and Diving Accidents
Publications are available that describe the risk of drowning, entrapment, and diving accidents. Available publications related to pool safety include the Association
of Pool and Spa Professionals’ (APSP) booklets entitled: The Sensible Way to Enjoy Your Aboveground/ Onground Swimming Pool, Children Aren’t Waterproof, Pool
and Spa Emergency Procedures for Infants and Children, Layers of Protection, and the latest published edition of ANSI/APSP-8 Model Barrier Code
for Residential Swimming Pools, Spas, and Hot Tubs.
Installer Responsibilities
All of these components shall be positioned so as to prevent their being used as a means of access to the pool by young children.
(See Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
SAVE THESE INSTRUCTIONS

FILTER PUMP MODEL
SFX600 Filter System
SFX1000 Filter System
SFX1500 Filter System
WATTAGE
70 watts
115 watts
180 watts
AMPERAGE
1.7amps
1.4amps
3.1amps
FILTER PUMP POWER INFORMATION
PARTS LIST
PRELIMINARY STEPS
FILTER PUMP IMPORTANT NOTES
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
PARTS NAME
Motor Seal Nut
Rubber Nozzle / Gasket
Pump Motor Assembly
Motor Seal / Canister Gasket
Top Cover
Weir Foam
Filter Cartridge
Weir
Filter Pump Skimmer Canister
O-ring for Hose
Connections
Hose Clamp
Return Hose
Elbow 90°
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
PARTS NAME
Return Fitting Lock Nut
Return Fitting Washer
(RF Washer)
Pool Wall (for reference only)
Fitting Gasket
Pool Wall Fitting
Return Fitting Diverter
Locking Ring
Return Fitting Service Plug
Skimmer Seal Ring
Water Stopper
SFX Skimmer Strainer Basket
Skimmer Gasket Rubber Seal
GFCI Power Cord Set (image reference only)
ITEMS ITEMS
1
2
3
4
5
6
7
8
9
1. READ ALL INSTRUCTIONS CAREFULLY and get a thorough understanding of what is required to assemble your SFX series Filter Pump.
2. Before you begin to assemble the pool, identify, count, and check all parts needed for assembly.
3. It is recommended that you have some PETROLEUM JELLY on hand for lubricating the gaskets.
1. Installer shall follow written instructions provided for operation of the filter pump systems.
2. All electrical components shall be installed in accordance with Article 680 of the National Electrical Code (NEC) “Swimming Pools, Fountains and Similar Installations”
or its latest approved edition.
3. The Type D Filter Cartridge 7 will hold as many as 2 of the 1” diameter chlorine tablets and the Type A/C Filter Cartridge 7 will hold as many as 6 of the 1”
diameter chlorine tablets. Check your chlorine levels to determine the proper number of chlorine tablets to add. The filter cartridge will automatically dispense chlorine
into the pool as the Filter Pump runs. You must have the type of Filter Cartridge with a central core mesh divider (See page 8) to use the chlorine dispenser.
DO NOT use this to dispense powdered chlorine, shock treatment or any other type of chemicals as damage to the pump, filter cartridge, and pool will occur.
4. The SFX Series Filter Pump systems are manufactured by Polygroup® and ETL control number 4000608 and 4006317 - double insulated and grounded - 120 Volts
A.C. - 60 Hz. (ALL Units must have a minimum of 105 Volts A.C. to start and run properly.)
OWNER’S MANUAL
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements. 7
7 7

THE FILTER CARTRIDGE 7 WILL HOLD 1" DIAMETER CHLORINE TABLETS.CHECK YOUR CHLORINE LEVELS TO DETERMINE THE PROPER NUMBER
OF TABLETS TO ADD.
Press
"RESET"
Button
To Start
Pump
Operation
How to use the GFCI plug
*Do not connect
to a timer device
6
9
5
3
4
2
1
8
7
8
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
Outside Pool Wall
Inside Pool Wall

SETUP INSTRUCTIONS
1. Set up the pool by following all the instructions that came with the pool. Do not
fill with water until the Filter Pump is properly installed. Locate the
Skimmer and Inlet openings on the pool wall.
3. Remove the Seal Ring by turning it counterclockwise. Make sure to keep
the Skimmer Gasket in the proper position. (see image below)
2. Remove the Skimmer Top Cover 5 and take out the parts contained
inside.
WARNING: CLIMBING HAZARD! PLEASE PREVENT CHILDREN FROM CLIMBING ON THE FILTER CANISTER TO GAIN ACCESS TO THE POOL.
Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.
Make sure the key
feature is facing the
correct location.
Make sure there is no gap here.
Make sure the two rubber keyways
are properly located before installation.
Inlet
opening
Skimmer opening
9
OWNER’S MANUAL
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
4. Place the threaded intake of the skimmer through the round skimmer
opening in the pool liner and screw the seal ring
22 tightly into place.
thread slots
Make sure the pool liner is on this
round surface and does not fall into
the thread slots as this may cause
leaking.
5. Assemble the wall fitting parts according to the following schematic.
6. Final assembly should look like the following schematic.
Make sure the hose clamp
is positioned properly over
the hose and o-ring to
ensure proper seal.
canister
It is recommended to point the diverter
down and away from the suction or water
intake for optimum pool circulation.
5
5
Inside Pool Wall
Inside Pool Wall
Outside Pool Wall
Inside Pool Wall

FILTER PUMP OPERATION
1. Plug the GFCI power cord to a properly grounded receptacle. It is recommended that the outlet is at least 15 feet (4.5m)
away from the pool.
2. IMPORTANT: To start the filter pump, press the RESET button on the GFCI plug .
3. Check the return fitting on the inside of the pool for correct flow, it should feel like a solid stream of water returning to the pool.
You can use the return flow as a gauge to determine when the filter needs cleaning or replacement. If you feel a
reduction in flow, clean or replace filter.
4. Test water and adjust chemicals as needed, read Section 9 - “POOL WATER CARE”. VERY IMPORTANT – FILTER PUMP
ALONE WILL NOT PREVENT ALGAE FROM GROWING IN POOL WATER; THIS CAN ONLY BE DONE BY MAINTAINING
PROPER CHLORINE AND pH LEVELS AT ALL TIMES!
5. The filter cartridge may need to be cleaned and/or replaced several times at start up until the correct chlorine and pH levels
are attained. We recommend that you keep at least one spare filter cartridge on hand at all times. Filter cartridges may be
purchased at the store you purchased your pool from, or ordered from Polygroup® at polygroupstore.com.
6. To turn off the filter pump, press the test button and unplug the GFCI power cord.
Press
"RESET"
Button
To Start
Pump
Operation
How to use the GFCI plug
*Do not connect
to a timer device
The water level should be
between the min and max
markers located inside the
skimmer canister ring.
Max. Level
Min. Level
Weir installation
finished.
a) Insert the weir pin
into the proper hole.
b) Push the weir
pin into the hole.
c) Retract the other weir pin, then release to
put it into the proper skimmer hole.
Push here
Push-in
The Filter Cartridge may
hold 1" diameter chlorine
tablets.Check your chlorine
levels to determine the
proper number of chlorine
tablets to add.
5
9
7. Install weir 8 onto the canister. Make sure the weir
foam insert is facing inside the canister.
8. Slip the Top Cover 5 onto the skimmer canister 9 .
10
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
59
Inside Pool Wall
Inside Pool Wall
Inside Pool Wall
9. Fill the pool with water. Continue filling the pool until the water has reached the
proper level. Plug in the GFCI, press the reset button to start the pump and enjoy
your pool.

IMPORTANT! Your filter pump is protected by a thermal switch. The switch senses the temperature of the filter pump. If it gets too hot, the switch
will stop the pump from running until it cools off. To restart the pump press the reset button on the GFCI when the filter pump has cooled down. This
is a safety device to prevent pump damage and prolong service life. If your pump is automatically turning off, it is because of high pool water
temperature and/or low water flow through the pump. If this happens you need to check the water flow and correct it if needed, as this filter pump
uses the water flow for cooling. It is recommended that you run the pump at night or early morning when the temperature is lower to prevent
overheating.
6.
7. Filter cartridges may be purchased at the store you purchased your pool from, or ordered from Polygroup®
at polygroupstore.com. Always replace with genuine Polygroup® SUMMER WAVES® filter cartridges.
FILTER CARTRIDGE CLEANING AND REPLACEMENT
PUMP MOTOR PROTECTION
1. Check and adjust pH and chlorine levels daily using required chemicals. See Section “POOL WATER CARE” or contact your local pool store.
2. Check filter pump output daily. If flow is reduced, see Symptom 2 in Section “TROUBLE SHOOTING GUIDE”.
3. Check filter pump, hoses and fitting for leaks. If a leak is found, see Symptom 4 in Section “TROUBLE SHOOTING GUIDE”.
4. Run the pump for the recommended number of hours daily. If you are unsure of the time frame please refer to support.polygroupstore.com for the
recommended "Pump Operation Hours" bases on pool types and sizes.
POOL MAINTENANCE
5.
24
7
5
11
OWNER’S MANUAL
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
Replace filter cartridge in canister, replace strainer basket replace top cover.
A Spare "stand by" Filter Cartridge 7 is an excellent investment. It provides a convenient way to
continue filtration of your pool while cleaning or replacing a dirty Filter Cartridge 7 . Also, a well
maintained, clean cartridge assures you that your filter will always be ready to operate at peak efficiency.
1. First, turn off & unplug the Pump. Then remove the Top Cover 5 .
Remove the Strainer Basket 24 and the Filter Cartridge 7
2. Basic Cleaning: Clean the filter cartridge by throughly pressure
washing inside and out with a garden hose. Allow a few hours for
the filter to fully dry and CAREFULLY BRUSH the pleats to avoid
damaging the filter cartridge. DO NOT scrub the pleated surface
areas. Cleaning and scrubbing a filter too vigorously will also wear
out the cartridge much faster than if it is simply hosed off correctly.
3. To remove tough oils (e.g. suntan lotion, body oils, etc...) it is
recommended to soak cartridge in a 1 lb. trisodium phosphate
solution (TSP or any other strong detergent) to 5 gallons water for
up to 12 hrs. Rinse cartridge to remove dirt. To remove algae, add
1/2 pint of pool chlorine or 1 pint of liquid household bleach to the
cleaning solution above. Leave the cartridge in the solution for 1
hour then thoroughly rinse before reuse.
4. Excessive c alcium and/ or mineral deposits may build up on a filter
cartridge and should be handled differently. Contact your local pool supply
store to ask about additional filter cartridge cleaners or treatment for
calcium or mineral deposits. Check pool chemistry for high pH or alkalinity;
this may cause a calcium or mineral build-up.
5
7

POOL WATER CARE
1. Hot weather or heavy use may require pH and chlorine levels to be maintained on the upper side of the scale and superchlorination of the pool every week.
2. Using a pool cover and/or solar cover (available at polygroupstore.com) will assist in maintaining your pH and chlorine levels by reducing the amount of
evaporation from your pool.
CAUTION - Concentrated chlorine levels and low pH levels will damage pool. You must follow the instructions for the pool chemicals you use, as to quantity and
recommended usage. NEVER drop lumps or pellets of chemicals into the pool; this may present a hazard to swimmers and/or damage your liner.
1. The following items are required and readily available from your local pool supply store:
• TEST KIT - Used to check chlorine and pH levels.
• 1” CHLORINE TABLETS - Used to disinfect pool water and help control the growth of algae.
• pH CONTROL CHEMICALS - Used to adjust pH levels Up (Soda Ash) or Down (Acid).
• ALGAECIDES - Used to eliminate algae.
• SUPERCHLORINATOR - Used to destroy combined chlorine, ammonia, nitrogen, and organic compounds.
• LEAF / SKIMMER NET with handle - Used to remove leaves, trash, insects, etc. from your pool. This item can be purchased at polygroupstore.com.
• FILTER CARTRIDGE CHLORINE DISPENSER (Inside Polygroup®’s patented Filter Cartridge U.S. Pat. 7,005,062) - Used to dispense 1” chlorine tablets ONLY.
See Section "FILTER PUMP IMPORTANT NOTES" on page 7.
2. Use test kit daily to check pH and chlorine levels. Adjust accordingly using the required chemicals.
NOTE : Excessive levels of chlorine or low pH levels will damage pool liner and may also change the color of the liner.
3. The pool can be cleaned using a maintenance kit with vacuum from Polygroup®. This item can be purchased at polygroupstore.com.
4. Using a foot bath near the pool to wash off your feet prior to entering the pool will assist in keeping the pool clean.
5. Well water often presents special problems with water chemistry. If you must use well water, take a sample to your local pool chemical supplier for analysis before
adding ANY chemicals.
6. Refer to the retail package box or visit the support pages at support.polygroupstore.com for the capacity of your pool. You will need this information to determine
the amount of chemicals you will need to properly maintain the pool water. NOTE: It is recommended to use a 5 gallon bucket of water to mix and dissolve any
chemicals before adding to the pool water.
Follow the manufacturer's label directions on all chemicals.*Most pool supply stores will test your pool water for free and advise you of what chemicals you need,
and the correct amount to use for your pool. You will need to tell them the pool capacity in gallons.
7. IMPORTANT - We cannot over-stress the importance of proper and adequate daily chemical treatment. Chlorine and pH levels must be properly maintained at all
times. PUMP AND FILTER ALONE WILL NOT PREVENT ALGAE FROM GROWING IN POOL WATER; THIS CAN ONLY BE DONE BY MAINTAINING PROPER
CHLORINE AND pH LEVELS AT ALL TIMES.
• Maintain pH level between 7.3 and 7.8.
• Maintain chlorine level between 1.0 and 1.6 ppm (parts per million).
• Superchlorinate your pool at least every other week or as needed.
NOTE :
Chlorine Tablets
12
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
Remove the top cover and skimmer
strainer basket to insert chlorine
tablets into Polygroup®’s patented
Filter Cartridges.

TROUBLESHOOTING GUIDE
PROBLEM CAUSE
1. Motor fails to start or
kicks on and off
A Unit Not Plugged In
B GFCI Outlet Breaker Tripped
C Low Voltage
2. No flow or low flow
through the return hose
A Low water level
B Inlet or Return Clogged
C Filter Dirty
3. Filter is not cleaning
pool. (water cloudy,
green,etc…)
A Chlorine level not in the
B Filter Dirty
C pH Level not in the
D Filter Cartridge is Damaged
E Low Water Flow
F Other Chemicals Required
G Pool Water Very Dirty
4. Water Leakage
A Hose area : Return hose
does not fit well with skimmer
cuff and wall fitting elbow
B Bottom of canister:
C Between canister and
liner: Incorrect installation.
POOL PUMP DISASSEMBLY & STORAGE
1. First, turn the pump off and unplug the main power cord of the system.
2. Remove the Top Cover 5 , Strainer Basket and Filter Cartridge 7 and remove any chlorine tablets left inside the core section of the filter.
3. Loosen all Hose Clamps . Remove the Return Hose and allow water to drain out.
4. Remove the Return Fitting - and clean the parts and lubricate Gask et with petroleum jelly and reassemble all parts then place them in a safe place.
5. Remove the Motor assembly 3 by turning the Motor Seal Nut 1 counter-clockwise. Now clean the pump, dry it off, and then lubricate the Motor Seal 4
on the motor with petroleum jelly and place it in a safe place.
6. Please refer to illustration on next page to reassemble the motor.
7. Remove the Filter pump canister 9 from liner by turning the Skimmer Seal Ring counter-clockwise. Remove the Weir 8 and Strainer Basket . Clean all
parts and dry them off. Then reassemble the filter cartridge, strainer basket, weir, top cover, etc. onto the canister. Place the assembled unit in a safe place.
8.All items should be stored in a dry environment that remains above 32 degrees Fahrenheit at all times.
SOLUTION
A Plug the GFCI into a 3-wire grounded outlet and press the reset button to turn pump on.
B Reset circuit breaker on electrical panel. If problem persists, have an electrician check circuit.
C Check the line voltage. It must be 105 to 125 AC volts.
A Water level must be between the Min/Max Limit Lines marked on Skimmer canister ring.
B Check for obstructions at strainer basket, filter cartridge, return hose and return fitting.
C Clean or replace cartridge. Spare cartridges make service more convenient.
A Maintain the chlorine level between 1.0 - 1.6ppm.
B Clean or replace cartridge (See page 11). Spare cartridges make service more convenient.
C Maintain the pH level between 7.3 - 7.8.
D Inspect the filter cartridge for holes or tears. If visibly damaged; replace the filter cartridge
E Check for obstructions at strainer basket, filter cartridge, return hose and return fitting.
G Chemicals are required to maintain clean pool water. Clean pool and filter more often.
F Have water tested at pool supply store. It may be necessary to add other
chemicals due to varying water quality in different localities.
A Make sure the hose clamp is positioned properly over the hose and o-ring to ensure a
proper seal. Adjust hose clamp, check o-ring and retighten.
Check hose for any holes or cracks and replace if needed.
B 1) The Motor Seal must sit in the inner groove in the bottom of the canister before
installing pump (Exception – the SFX1500 only has one groove). 2) Check pump alignment.
The arrow with the indentation on the pump MUST point to the matching indentation on the
canister. 3) Make sure that the Motor Seal Nut (Locking ring) is not cross threaded.
WARNING: UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE FILTER PUMP.
13
OWNER’S MANUAL
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
suitable range.
suitable range.
11
C Make sure the Skimmer Gasket Rubber Seal 25 is installed properly (see page 9 steps 3
& 4). The key feature should be at the top. Make sure the liner is not in the threaded grooves.
No gap should be visible in this area. Screw the Seal Ring tightly onto canister.
11 12
17

PUMP REMOVAL INSTRUCTIONS FOR TROUBLESHOOTING
IMPORTANT: The recommended method to troubleshoot or replace the pump is to remove the entire filtration system. Please drain enough water from the
pool so that the water level is below the skimmer opening. Then remove the entire skimmer system following the directions below.
5. Slide motor seal nut down cord and out of the way. Remove pump
3 from canister. Be careful not to lose the rubber nozzle or the
motor seal gasket . You may need to reach inside the canister to
release the seal between the canister and the pump.
3. Unscrew the locking ring and remove the diverter fitting (threaded
style) or unsnap the diverter fitting (snap-on style) and insert the return fitting
plug (RF plug).
1. First, turn the pump off and unplug the main power cord of the system. (REMEMBER TO KEEP ALL PARTS IN A SAFE PLACE FOR REASSEMBLY LATER)
2. Insert the water stopper into the skimmer opening and push the stopper in to make it engage with the skimmer seal ring making a tight seal to block the water.
2
3
14
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
1. First, turn the pump off and unplug the main power cord of the system. (REMEMBER TO KEEP ALL PARTS IN A SAFE PLACE FOR REASSEMBLY LATER)
2. Remove the top cover, strainer basket and filter cartridge and remove any chlorine tablets left inside the core section of the filter.
3. Unscrew the locking ring and remove the diverter fitting (threaded style) or unsnap the diverter fitting (snap-on style) and insert the return fitting plug (RF plug).
4. IMPORTANT: You may get wet. The next step will drain any water that remains in the canister and in the return hose.
5. Loosen the hose clamp on the return fitting at the pool wall, carefully remove the hose from the return fitting and allow the water to drain out of the hose and the
canister. NOTE: You may also remove the hose from the canister but it is not required.
6. Remove the skimmer seal ring to release the canister and remove the filtration system from the pool.
7. Flip the canister over and turn the motor seal nut counterclockwise until free, then remove the pump.
CAUTION: If you prefer to leave the skimmer filtration system attached to the pool we recommend having two people available to follow the process
below. PLEASE NOTE: The incorrect handling method may cause damage resulting in water leakage between the canister and liner wall.
4. Remove top cover 5 , strainer basket , filter cartridge
24
7 , it is advised to
use a water container, such as a bucket (shown with dotted line in the illustration
above) to collect the purged water.
Caution this next step takes two people. One person should hold the water stopper
and canister firmly while the other person removes the motor seal nut
1 by
turning according to the arrow direction in the illustration above. DO NOT pull or
push the canister as this may cause damage between canister and pool liner wall.
You may need to reach
inside canister to free pump.
4
4
2
1

ROTOR INSPECTION AND REPLACEMENT INSTRUCTIONS
2
15
OWNER’S MANUAL
1. Once the pump 3 has been removed from the canister 9 you are ready to inspect or replace your rotor assembly .
2. Refer to below pump motor assembly illustration for your specific pump size to replace the rotor assembly .
3. Remove the volute cover by unscrewing the volute cover lock nut (SFX600/SFX1000) or by unscrewing the bolts (SFX1500) that hold down the volute
cover and pull out the rotor assembly . Please be careful as the rotor assembly has multiple parts which may come out separately. (see image below)
4. Inspect the rotor assembly to make sure that it has all of its parts and that the center shaft, magnetic axle, or impeller blades are not broken as this will
cause the pump to fail. If your rotor assembly is broken a complete rotor assembly may be purchased at polygroupstore.com without having to replace the whole
pump. Please see Pool Support - Filtration System Troubleshooting for the SFX Filtration System at support.polygroupstore.com.
PLEASE NOTE: Even if the rotor assembly is in perfect condition if it is not seated properly between the volute cover and the pump it will not function correctly.
5. Once the rotor assembly has been checked or if replacing with a new rotor assembly, slowly insert the rotor assembly back down into the pump carefully. The
force of the magnet will pull the rotor assembly into the pump. Ensure that the rotor assembly is assembled and aligned correctly inside the pump body .
6. Once the rotor has been inserted, fasten the volute cover by screwing the volute cover lock nut (SFX600/SFX1000) or by screwing in the bolts
(SFX1500) that hold down the volute cover.
SFX600 or
SFX1000 SFX1500
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
2
Rotor Assembly Parts

OWNER’S MANUAL
16
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
PUMP REPLACEMENT INSTRUCTIONS
Outlet of canister and rubber nozzle
on the pump should be aligned.
1. Lubricate the motor seal gasket (if needed) and Insert it into the inner groove (SFX600/SFX1000) or single groove (SFX1500) on the bottom of the
canister .
2. Please make sure the cord has been placed through the motor seal nut before replacing pump. If the canister was left on the pool; reach in through the
canister and pull the pump upwards. Slowly insert the pump motor assembly back into the canister, so that the rubber nozzle is aligned with the hose
opening on the canister. Please make sure the pump is correctly aligned, if it is not aligned correctly it can still lock on but may leak.
3. If the canister was removed from the pool, once the pump is inserted into the canister, please make sure the arrow with the indentation is pointing to the
matching indentation on the canister. There is a groove on the pump that needs to be aligned with the notch on the canister (visible from bottom only).
4. Slide the motor seal nut up to the canister base and carefully tighten onto the threads making sure it is not cross threaded. Cross threading can cause leaking
out of the bottom of the canister.
Make sure notch and groove are aligned.
Step 3.
Step 4.
TOP VIEW
Step 1. Step 2.
BOTTOM VIEW OF PUMP AND CANISTER
Close Up
1
2
32
4
4
9

REPLACEMENT PARTS ORDERING INFORMATION
SFX600 SFX1000 SFX1500
1
2
3
4
5
6
7
8
9
Key Description PART #
11
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
28
29
30
Motor Seal Nut
Rubber Nozzle / Gasket
Pump Motor Assembly
Motor Seal / Canister Gasket
Top Cover
Weir Foam
Type D Filter Cartridge
Type A/C Filter Cartridge
Weir
Filter Pump Skimmer Canister
O-ring
Hose Clamp
Return Hose
Elbow 90°
Return Fitting Lock Nut
Return Fitting Thrust Washer (RF Washer)
Pool Wall (for reference only)
Fitting Gasket
Pool Wall Fitting
Return Fitting Diverter
Locking Ring
Return Fitting Service Plug
Skimmer Seal Ring
Water Stopper
SFX Skimmer Strainer Basket
Skimmer Gasket Rubber Seal
Rotor Assembly
Volute Cover
Volute Cover Lock Nut (X-600 & X-1000)
Volute Cover Bolt And Nut Set (X-1500 ONLY)
--
P58PP1954W05
P58PP1954G8U
P58182601K01
P58X600C0000
P58147800K01
P58PP1950W05
P58PP1950G8U
P58SFX000W01
P581041037PR
--
P58PP1956W05
P58PP1956G8U
P58PP1984W05
P58PP1984G8U
P58030001K01
P58220221W05
P58220221G8U
P58125009W01
P58PF1740W05
P58PF1740G8U
P58PF1690W05
P58PF1690G8U
P58PF2960W05
P58PF2960G8U
--
P58PF1730K01
P58PF1680W05
P58PF1680G8U
P58PF1721W05
P58PF1721G8U
P58PF1710W05
P58PF1710G8U
P58PF0620K01
P58PP1953W05
P58PP1953G8U
P58PP2163K01
P58PP1952P01
P58PP1957W05
P58050137001
P58PF1009K01
P58PF1010K01
--
P58PP1954W05
P58PP1954G8U
P58182601K01
P58X1001C000
P58147800K01
P58PP1950W05
P58PP1950G8U
P58SFX000W01
--
P581041080PR
P58PP1956W05
P58PP1956G8U
P58PP1951W05
P58PP1951G8U
P58037000K01
P58219221W05
P58219221G8U
P58150012W01
P58PF1700W05
P58PF1700G8U
P58PF1690W05
P58PF1690G8U
P58PF2960W05
P58PF2960G8U
--
P58PF1730K01
P58PF1680W05
P58PF1680G8U
P58PF1721W05
P58PF1721G8U
P58PF1710W05
P58PF1710G8U
P58PF0620K01
P58PP1953W05
P58PP1953G8U
P58PP2163K01
P58PP1952P01
P58PP1957W05
P58050505001
P58PF1010K01
--
P58PP1954W05
P58PP1954G8U
P58185201K01
P58X1500C000
P58164800K01
P58PP1950W05
P58PP1950G8U
P58SFX000W01
--
P581041080PR
P58PP1956W05
P58PP1956G8U
P58PP1983W05
P58PP1983G8U
P58037000K01
P58219221W05
P58219221G8U
P58150012W01
P58PF1700W05
P58PF1700G8U
P58PF1690W05
P58PF1690G8U
P58PF2960W05
P58PF2960G8U
--
P58PF1730K01
P58PF1680W05
P58PF1680G8U
P58PF1721W05
P58PF1721G8U
P58PF1710W05
P58PF1710G8U
P58PF0620K01
P58PP1953W05
P58PP1953G8U
P58PP2163K01
P58PP1952P01
P58PP1957W05
P58050506001
P58184501K01
--
P5800400080A
Should you encounter any problems, contact Customer Service at [phone] from 8 AM to 5 PM Mon. thru Fri.
MST. Extended operating days and hours during peak season requirements.
OWNER’S MANUAL
17
P58PF1009K01

MANUAL DE USUARIO
BOMBA SUMMER WAVES®
CON FILTRO SKIMMERPLUS®
PARA PISCINAS SOBRE SUELO
Modelos SFX600 / SFX1000 / SFX1500
LEA ESTAS INSTRUCCIONES Y CONSÉRVELAS PARA FUTURAS CONSULTAS
DISTRIBUIDO POR: Polygroup® LIMITED (MACAO COMMERCIAL OFFSHORE)
Unit J, 10th Floor, Macau Square, Av do Infante D.Henrique, No.43-53A, Macao Manual #
09C3A40USA17
1
Para dudas sobre la instalación o resolución de problemas, visite
support.polygroupstore.com Servicio de atención al cliente: [phone]
NO DEVUELVA EL PRODUCTO A LA TIENDA
Para pedir piezas y accesorios,
visite www.polygroupstore.com
Si le surge algún problema con su producto Polygroup®, no devuelva el producto al establecimiento de compra. Las reclamaciones por garantía deben realizarse
directamente a Polygroup®. Antes de ponerse en contacto con el servicio de atención al cliente, revise la guía de resolución de problemas, en el manual de instalación,
o consulte las FAQ o revise los videos con las instrucciones en support.polygroupstore.com. Si continúa sin poder resolver el problema, póngase en contacto con
el servicio de atención al cliente de Polygroup® en el [phone]. Tenga preparado el tipo de producto , el numberó de modelo y el comprobante de compra listo.
Nuestro representante del servicio de atención al cliente le ayudará a resolver el problema. Puede ser necesario que nos envíe parte del producto o el producto en su
totalidad para inspección y/o reparación. No devuelva ningún producto a Polygroup® sin un número de autorización de devolución.
GARANTÍALIMITADA
Polygroup® Limited (empresa comercial extraterritorial de Macao), (en adelante, “Polygroup®”) garantiza solo al comprador original la bomba eléctrica de tipo
SFX ante defectos en el material y mano de obra durante 180 días desde la fecha de compra. El comprador original debe conservar el justificante de compra en
forma de recibo de venta original de la tienda, que deberá presentar si así se lo solicita Polygroup® o sus agentes delegados. Las reclama ciones de garantía no
pueden procesarse sin un justificante de compra válido. Esta garantía limitada solo se aplica al comprador original del producto y se limita a la reparación o
sustitución del producto, a discreción de Polygroup®. Los daños consiguientes, incluidas reclamaciones por pérdidas de agua, químicos para piscinas, daños
o uso no están cubiertos por esta garantía limitada.
Esta garantía no se considerará válida en caso de modificación o reparación del producto por parte del comprador o de personas no autorizadas, uso de
e piezas o accesorios no originales de Polygroup® en el producto, uso del producto contraviniendo las instrucciones del fabricante, uso de voltaje inadecuado,
cualquier tipo de abuso del producto o en caso de accidente o negligencia. Esta garantía no cubre el desgaste normal, así como los casos de fuerza mayor
fuera del control de Polygroup®. Polygroup® no se hace responsable de las hierbas que pueden crecer a través del paño de tierra y / o el revestimiento de la
piscina, ya que esto no es un defecto de fabricación.
EN NINGÚN CASO SERÁN RESPONSABLES Polygroup®, SUS AGENTES AUTORIZADOS, ENTIDADES ASOCIADAS O EMPLEADOS ANTE EL COMPRA
DOR O TERCEROS POR DAÑOS DIRECTOS O CONSIGUIENTES. Algunos estados o países, u otras jurisdicciones, no permiten la exclusión o limitación de
daños accidentales o consiguientes, en cuyo caso no se aplicarán las anteriores limitaciones o exclusiones.

Advertencias...................................................................................................................................................
Pasos preliminares, Notas importantes acerca de la bomba de filtración é Información sobre la potencia del motor y la
Lista de piezas...........................................................................................................................................................................
Instrucciones de montaje y Funcionamiento de la bomba de filtro.................................................................
Protección del motor; Limpieza y sustitución del cartucho del filtro y Mantenimiento de la piscina....................................................
Tratamiento del agua de la piscina.................................................................................................................
Guía de resolución de problemas, Desmontaje y almacenamiento de la bomba...........................................
Instrucciones para reempalzar el motor y para solucionar problemas...........................................................
Inspección del rotor instrucciones de reemplazo...........................................................................................
Instrucciones del reemplazo del motor...........................................................................................................
Información sobre el pedido de piezas de repuesto.......................................................................................
3 ~6
7 ~8
9 ~ 10
11
12
13
14
15
16
ÍNDICE
2
En caso de problemas, póngase en contacto con el servicio de atención al cliente en el [phone], de L a V de 8h a 17h.
MST. Los horarios de atención se amplían durante temporada alta.
17