Polytree TZ66M3545X03 User manual

TREE ASSEMBLY INSTRUCTIONS
SNOITCURTSNIYLBMESSA ANIHCNIEDAM
MODEL #: TZ66M3545X03,TZ66M3545X04
Fig. B
C
D
B
E
F
G
TREE TOP
ROW
WITHOUT COLOR
COLOR CODED
RED
YELLOW
GREY
DARK BLUE
LIGHT BLUE
DARK PURPLE
Congratulations on purchasing your new tree from Polytree®! Carefully follow the instructions
below on how to quickly and easily set up your new tree.
1. Before you start to assemble your tree, choose an appropriate location near a wall outlet.
2. Assemble the tree stand and place on a level surface. (See Fig. A) Then insert the tree pole
tightly into the stand.
3. Sort all branches according to color codes marked on the end of each branch. Below is a list
of the color codes for your tree. (See Fig. B) (Please note: the number of rows may vary with different tree sizes.)
1. Shape each branch by either placing the branch in a bracket which is at a comfortable level to work(Fig. 1), or
holding the branch in your hand with the hooked end pointing down. (Fig.2) BEGIN WITH THE BRANCHES AT THE
BOTTOM OF THE TREE AND WORK UP TOWARDS THE TOP.
2.When shaping each branch, work from the branch hook and move outwards to the end tip of the branch. Start by
wrapping the back tip around the end of the branch stem to cover the branch wire.(Fig. 3)
3.Working from the branch's hook moving outwards, fan each tip out using this pattern: one tip to the right of the
branch's center wire, one tip to the left of the branch's center wire, one tip parallel to the branch's center wire.
(Fig. 4) Tips should be slightly offset from each other so that they do not line up exactly one behind the other. All
tips should be curved upwards when looked at from the side. (Fig. 5)
4. As each branch is shaped, place the color coded branch securely into the matching color coded bracket. (Fig. 6)
As you finish each level of branches, make sure the rows look evenly distributed to the levels above and below it.
Adjust tips as needed to even appearance. (If your tree includes branches with side wings, arrange these
branches so that the wings are on every other branch if necessary.)
5.When all the branches are shaped and put into their color coded matching brackets, shape the top section. Do
this by pulling down each row of tips in an even, circular pattern. (Fig. 7)
6. Start from the bottom layer of the tree topper and work upwards to the top tip.
7. Carefully curve each tip upwards for a natural look.
8. Insert top securely into tree's center pole.(Fig. 8)
9. Step back and take an overall look at the tree. Shift tips as needed to fill in any gaps. Slightly upsweep all branch
tips for a uniform look.Your Christmas tree is now complete and ready to be decorated. (Fig. 9)
SHAPING AND ADDING BRANCHES
Fig. 3
Fig. 6 Fig. 8
Fig. 4
Branch
Fig. 5
Side view
Fig. 2Fig. 1
Fig. 9Fig. 7
Please scan code to
learn how to shape
and set up your tree
Insert and slide the legs
upward into the slots of the
base until firmly secured.
Fig. A - Tree Stand Assembly

SNOITCURTSNIYLBMESSA ANIHCNIEDAM
1. Remove all ornaments and decorations.
2. Start by removing the tree top and then removing each layer of branches going from top to bottom of the tree.
3. In case of difficulty separating the tree pole (trunk), apply a small amount of lubricant at the joint and
rotate the upper pole in both directions. Lift up the upper pole again.
4. Press tips neatly back to the center of branch wire.
5. Carefully place all tree sections and branches into shipping box and tape it shut.
6. When not in use, please store the tree in a cool, dry place away from sunlight.
STORAGE TIPS
CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact
us at 1-888-919-0070 or visit our website at www.polygroup.com. One of our customer service
representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX. TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address:(No P.O. Boxes)
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem: