Ponca Technologies PT?7501 User manual









HD/SD-SDI over Multimode LC-type
Fiber Optic Extender with Loop-out
PT‐7501


UserManual
PONCA
Technologies

~ 1 ~
SafetyandNotice
The PT-7501 HD/SD-SDI over Multimode LC-type Fiber Optic Extender with Loop-out has been tested for
conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic
equipments, the PT-7501 should be used with care. Please read and follow the safety instructions to protect yourself from
possible injury and to minimize the risk of damage to the unit.
zFollow all instructions and warnings marked on this unit.
zDo not attempt to service this unit yourself, except where explained in this manual.
zProvide proper ventilation and air circulation and do not use near water.
zKeep away the objects that might damage the device and assure that the placement of this unit is on a stable surface.
zUse only the power adapter, power cords and connection cables designed for this unit.
zDo not use liquid or aerosol cleaners to clean this unit.Always unplug the power to the device before cleaning.

~ 2 ~
The PT-7501 is an ideal and economic solution designed for transmission of multi-rate SDI video, with embedded
audio and metadata over a multi-mode optical fiber cable.
The transmitter module (PT-7501-TX) receives one HD-SDI electrical input, perfectly converts SMPTE 292M,
SMPTE 259M, or DVB-ASI electrical SDI signal to multi-mode optic SDI signals. The receiver module (PT-7501-RX)
receives optical signal from input LC connector, and then perfectly converts it to electrical SDI signal. Both transmitter and
receiver provide equalizing and re-clocking at input unit in order to re-construct the signal for consistent quality. The
PT-7501 is perfect for today’s broadcast applications, including video production, video editing, studio to studio and studio to
CATV head end. In addition, since transmission of content is inherently secure and immune to outside interference, fiber
applications are favored in government, military, and medical environments.
Introduction

~ 3 ~
Features
zEnable transmission of digital video signal over optical fiber up to 1 km
zAutomatic cable EQ up to 300m (1000ft) at SD-SDI or 150m (500ft) for HD-SDI
zStandard LC-type fiber optic connector
zSupports following protocols:
— SMPTE 259M (270Mbps)
— SMPTE 259M (360Mbps)
— SMPTE 292M / HDTV (1.485Gbps and 1.485/1.001Gbps)
— DVB ASI (270Mbps)
zAutomatic reclocked / Manual bypass (optional upon request)
zOne SDI loop-out and one SDI BNC output
zHD/SDI Input signal detection LED
PT-7501 PT-7510 PT-7520 PT-7540 PT-7580
SDI Loop-Out ●●●●●
DVB Support ●●●●●
Immune to RP-1981●●●●
HD/SD Detection ●●●●●
Re-clocking ●●●●●
Cable EQ ●●●●●
Jitter (<0.2 UI) ●●●●●
Bandwidth(1.5Gbps) ●●●●●
Fiber Type2M S S S S
Optics type LC LC LC LC LC
Transmission3~500m ~10km ~20km ~40km ~80km
1RP‐198isthePathologicalPatterns.
2Fibertype:M=multi‐mode;S=single‐mode.
3Maximumtransmissionlengthisdependedupontheopticsmodule.
SDI over Fiber Series Lineup

~ 4 ~
Specifications&PackageContents
Model Name PT-7501
Technical PT-7501-TX PT-7501-RX
Role of usage Transmitter Receiver
SDI standards SD-SDI & HD-SDI
Auto HD/SD-SDI detection Yes
Supported protocols SMPTE 259M (270Mbps / 360Mpbs), DVBASI (270Mbps)
SMPTE 292M / HDTV (1.485Gbps and 1.485/1.001Gbps)
Video bandwidth [1.485Gpbs & 1.485/1.001Gbps]
Data rates 270 / 1483 / 1485 Mbps
Video support [HD] 720p50/59.94/60, 1035i50/59.94/60, 1080i50/59.94/60, 1080p24/30
[SD] [email protected], PAL@50Hz
SDI signal type SMPTE-292M, SMPTE-259M, DVB-ASI
Output impedance 75Ω
Auto reclocker mode Automatic detection: 270Mbps / 1.483Gbps / 1.485Gbps
Automatic bypass: 177Mbps / 360Mbps / 540Mbps
Fiber Transmission [HD] up to 500m (550yd)
[SD] up to 1 km (1100yd)
Cable (Belden 1694A)
equalization / transmission [HD-SDI] up to 150m (500ft) [SD-SDI] up to 300m (1000ft) [HD-SDI] greater than 125m (410ft) [SD-SDI] up to 300m (1000ft)
Loop-out 1 reclocking SDI loop-out
Audio support Yes
RP-198 pathological patterns Not immune
PCB Stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω]
Input 1x BNC [SDI] 1x Optical LC [SDI]
Output 1x Optical LC [SDI]
1x BNC [SDI] (loop-out) 2x BNC [SDI]
BNC connector 75Ωinter-locked socket
Optical fiber connector LC-type
Fiber optics
Wavelength: 850 nm
Extinction ratio: 8-10
Overshoot < 10%
Optical power: -4 to -10 dBm
Type: Multi-mode
Jitter < 0.2 UI
Rise/fall < 500 pS
Receiver sensitivity: -17 dBm
Mechanical
Housing Metal case
Model 110 x 40 x 30mm [4.3”x1.6”x1.2”]
Package 330 x 200 x 95mm [1’1”x7.9”x3.7”]
Dimensions
[Lx W x H] Carton 495 x 440 x 380mm [1’7.5”x1’5.3”x1’3”]
Model [TX / RX] –155g [5.5oz]
Weight Package 1200g [2.5 lbs]
Inter-locked power supply
Power supply 5V 4ADC
Power consumption 5 Watts [max]
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
Package Contents 1x PT-7501 [TX & RX] 2x 5V power adapter
1x User Manual

~ 5 ~
Transmitter(PT‐7501‐TX)
Receiver(PT‐7501‐RX)
Panel Descrip
t
ion
s
BNC Input: Plug in coaxial cable here
Optical fiber output: Plug in optical fiber to the left
Optical fiber input: Plug in optical fiber to the right
BNC output: Plug in coaxial cable here
Power LED
SDI signal LED
RearPanel
FrontPanel
BNC output
5V power jack
Power LED
SDI signal LED
5V power jack
FrontPanelRearPanel
BNC loop-out

~ 6 ~
The SELLER warrants the PT-7501 HD/SD-SDI over Multimode LC-type Fiber Optic Extender with Loop-out to be free from
defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this
product fail to be in good working order within 1 year warranty period, The SELLER, at its option, repair or replace the unit, provided
that the unit has not been subjected to accident, disaster, abuse or any unauthorized modifications including static discharge and
power surges.
Unit that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time
of repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the unit is delivered by mail, customers
agree to insure the unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted without a return
authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without limitations, any other implied warranty or
fitness or merchantability for any particular purpose, all of which are expressly disclaimed. Proof of sale may be required in order to
claim warranty. Customers outside USA are responsible for shipping charges to and from the SELLER. Cables are limited to a 30 day
warranty and cable must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assumes no
responsibility for any inaccuracies that may be contained in this manual. The SELLER will NOT be liable for direct, indirect, incidental,
special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such
damages. Also, the technical information contained herein regarding the PT-7501 features and specifications is subject to change
without further notice.
Limited Warranty