Popp POPE700700 User manual

RF433 Bridge
POPE700700
POPE700717
Quick start:
1. Connect the device to a USB port.
2. If the LED flashes purple, connect to the open Wi-Fi bridge433-XXXX.
3. Enter the IP address 192.168.4.1 in the browser bar.
4. Set in the configuration mask your Wi-Fi, the IP address
and the communication port of your gateway. (8000)
5. Save the setting and activate the bridge.
6. Install the RF433 application in the POPP Hub.
Configuration of the RF433 Bridge
1. Wi-Fi - settings:
SSID: Enter the name of your home Wi-Fi.
Password: Enter the password of your home Wi-Fi.
Scan: Scan the environment for existing Wi-Fi networks
(If the page remains empty, please check your wireless connection to the bridge).
DHCP: If checked, the IP address assigned by your router is used.
IP/Netmask: Specify the IP address and network affiliation of the bridge.
Gateway: Enter the IP address of your router.
2. SmartHome Gateway - Settings:
IP: Enter the IP address of your Smart Home Gateway (POPP Hub).
Port: Enter the communication port to your SmartHome Gateway.
Advanced settings:
Code send repeats: Set the number of transmission repetitions of a command
(minimum 1; maximum 25). This may be necessary for some devices with poor
communication.
3. Save Settings: Save the settings.
4. Activate Bridge: Activate the 433Mhz bridge. The device restarts and then connects
to your Wi-Fi and SmartHome Gateway.
Reset Settings: Resets the unit to factory settings.
LED indication:

Purple pulsating Device starts
Flashing purple Configuration mode
Blue flashing Establishing a connection to the Wi-Fi network
Blue light Wi-Fi is connected
Red light A connection to the Wi-Fi is not possible
Yellow on No connection to SmartHome Gateway possible
Green flickering Reception indicator 433Mhz
White flickering Transmission indicator 433Mhz
Configuration mode:
To start the configuration mode, press the button on the 433 Mhz bridge for 4 seconds. The configuration mode is indicated by a
purple flashing. This mode can only be terminated via the configuration interface.
Resetting the device to the factory settings:
Press the button on the 433 Mhz bridge for 4 seconds, the unit switches to configuration mode, which is indicated by a purple
flash. Press the button again for 4 seconds, the LED changes to yellow before the unit restarts and returns to the factory
settings.
Sources of error:
LED indication
Error
Solution
Glowing yellow
IP address of the SmartHome Gateway is
wrong
Check the IP address of the SmartHome Gateway
within the configuration mode.
Glowing yellow
Does not get an IP address assigned
Check the DHCP settings on your router and in the
configuration mode of the gateway. Specify a static
IP address.
Glowing yellow
Port settings do not match between 433Mhz
Gateway and SmartHome system
Check the transfer port within the configuration
mode of the 433Mhz bridge and in your SmartHome
Gateway. This is 8000 by default.
Blue flashing
(min. 10s)
Wi-Fi connection could not be established
Within configuration mode, check the SSID and
password.
Glowing red
A connection to the Wi-Fi is not possible
Within configuration mode, check the SSID and
password.
Support
If you encounter a problem, please use the international community at www.z-wave.info (English) or www.zwave.de (German),
our website at www.popp.eu/support or contact us by e-mail: [e-mail]
Declaration of Conformity
Popp hereby declares that this device complies with the essential requirements and other relevant provisions of Directive RED
2014/53/EU. The complete declaration of conformity can be found at the following address: www.popp.eu/ce
Questions regarding the declaration of conformity should be addressed to the following address:
Popp & Co, Große Johannisstr. 7, 20148 Hamburg, Germany
Disposal guidelines
Electronic devices may not be thrown away in domestic waste, but must be disposed of separately. Please inform yourself about
your local legal regulations and the disposal system available to you. Disposing of electronic equipment in landfills or dumps can
cause hazardous substances to enter groundwater and above into food and ultimately endanger your health.