Porcelanosa Noken CITY USA 160234 N710001174 User manual

CITY USA
CITY USA WITH APRON
CITY USA WITHOUT APRON

2
Noken Design baths are manufactured to the strictest standards to ensure quality performance and full customer satisfaction at all times.
Each and every one of our baths is assembled and tested before leaving the factory.
All plumbing installation work should be effected in compliance with national regulations concerning plumbing installations in buildings.
The system must only be installed by qualified professionals.
Noken Design S.A. declines all responsibility in the event of improper installation.
The maximum recommended water hardness for the range of baths is 18ºTH (French degree of hardness) / 13ºe (English degree of hardness).
The baths are not designed to be used for seaweed, mud or seawater treatments, etc.
There is an increased risk of falls when the surface of most baths is wet and therefore slippery. This is particularly true when soap, shampoo, bath oils
and other similar products are used. Users of baths must be aware of this fact.
NB: Before proceeding with the installation, check that all the parts supplied are in perfect condition. Notify the carrier immediately if this is not the
case.
Les baignoires Noken Design sont fabriquées selon des critères de qualité très exigeants afin de garantir la satisfaction de l’utilisateur final.
Les baignoires sont montées et testées une par une dans nos installations, et soumises à de rigoureux contrôles techniques et de sécurité, pour nous
assurer qu’elles fonctionnent correctement avant d’abandonner l’usine.
Les travaux de plomberie doivent être effectués conformément aux réglementations en vigueur dans chaque pays pour les installations de plomberie
dans les bâtiments.
L’installation ne peut être réalisée que par un installateur qualifié uniquement.
Noken Design S.A. décline toute responsabilité en cas d’installation incorrecte.
La dureté maximale recommandée de l’eau pour la gamme de baignoires est de 18ºTH (Degrés français) / 13ºe (Degrés anglais).
Les baignoires n’ont pas été conçues pour les traitements aux algues, aux boues, aux eaux marines, etc.
Lorsqu’elle est humide, la surface de la plupart des baignoires présente un risque potentiel accru de dérapage. Ce risque est plus important en cas
d’utilisation de savons, de shampoings, d’huiles pour le bain et d’autres produits similaires. Il est très important que les utilisateurs des baignoires
en soient conscients.
Remarque: S’assurer que les pièces de la baignoire sont en parfait état avant de procéder à son installation. Si ce n’est pas le cas, adresser une
réclamation au transporteur.
Las bañeras Noken Design han sido fabricadas con elevadas exigencias y pensando, en todo momento, en la satisfacción del usuario final.
Las bañeras son montadas y puestas a prueba, una a una, superando rigurosos controles técnicos y de seguridad, en nuestras instalaciones, para
verificar su correcto funcionamiento, antes de salir de fábrica.
La instalación de fontanería debe hacerse de acuerdo con la reglamentación vigente en cada país para las instalaciones de fontanería en edificios.
La instalación debe ser realizada exclusivamente por un instalador cualificado.
Asimismo Noken Design S.A. declina toda responsabilidad en caso de una instalación incorrecta.
La máxima dureza del agua aconsejable para esta gama de bañeras es de 18ºTH (Grados franceses) / 13ºe (Grados ingleses).
Las bañeras no han sido diseñadas para tratamientos con algas, barros, aguas marinas, etc.
Cuando está húmeda, la superficie de la mayor parte de las bañeras presenta un aumento del riesgo potencial de deslizamiento. Esto es más
significativo cuando se utiliza jabón, champú, aceites para el baño y otros productos similares. Es importante que los usuarios de las bañeras sean
conscientes de esto.
Nota: Verificar, antes de realizar la instalación, el perfecto estado de las piezas. En caso contrario, reclamar al transportista.

3
EPYTNOITISOPSNOISNEMID
OPITNÓICISOPSENOISNEMID
"13"06471100017N432061001detargetnitfel 15/16 19" 11/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160279 N710001170 60" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
"13"06561100017N003061001detargetnithgir 15/16 19" 11/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160278 N710001166 60" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
"13"66271100017N532061001detargetnitfel 15/16 19" 11/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160301 N710001171 66" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
"13"66371100017N292061001detargetnithgir 15/16 19" 11/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160291 N710001169 66" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
17461100017N703061001detargetnitfel 15/16" 31" 15/16 19" 11/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160305 N710001168 7115/16" 31" 15/16 19" 7/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
17761100017N603061001detargetnithgir 15/16" 31" 15/16 19" 11/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
17571100017N392061001tuohtiwahcered 15/16" 31" 15/16 19" 7/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
SAP KEA A B C D E F G H I J K LAPRON
3-wallalcove. Tail flange included
60"X 32"
66"X 32"
72"X 32"
DIMENSIONS POSITION TYPE
DIMENSIONES POSICIÓN TIPO
left 3-wall alcove 100160234 N710001174 60" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda built-in / encastre 100160279 N710001170 60" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
right 3-wallalcove 100160300 N710001165 60" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha built-in / encastre 100160278 N710001166 60" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
left 3-wall alcove 100160235 N710001172 66" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda built-in / encastre 100160301 N710001171 66" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
right 3-wallalcove 100160292 N710001173 66" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha built-in / encastre 100160291 N710001169 66" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
left 3-wall alcove 100160307 N710001164 71 15/16" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
izquierda built-in / encastre 100160305 N710001168 7115/16" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
right 3-wallalcove 100160306 N710001167 7115/16" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
derecha built-in / encastre 100160293 N710001175 71 15/16" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
J K L
60" X 32"
66" X 32"
72" X 32"
SAP KEA A B C D E F G H I
EPYTNOITISOPSNOISNEMID
OPITNÓICISOPSENOISNEMID
"13"06471100017N432061001detargetnitfel 15/16 19" 11/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160279 N710001170 60" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
"13"06561100017N003061001detargetnithgir 15/16 19" 11/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160278 N710001166 60" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
"13"66271100017N532061001detargetnitfel 15/16 19" 11/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160301 N710001171 66" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
"13"66371100017N292061001detargetnithgir 15/16 19" 11/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160291 N710001169 66" 31"15/16 19" 7/16 1" 10"1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
17461100017N703061001detargetnitfel 15/16" 31" 15/16 19" 11/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160305 N710001168 7115/16" 31" 15/16 19" 7/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
17761100017N603061001detargetnithgir 15/16" 31" 15/16 19" 11/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
17571100017N392061001tuohtiwahcered 15/16" 31" 15/16 19" 7/16 1" 10"1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
SAP KEA A B C D E F G H I J K LAPRON
3-wallalcove. Tail flange included
60"X 32"
66"X 32"
72"X 32"
DIMENSIONS POSITION
DIMENSIONES POSICIÓN
left integrated 100160234 N710001174 1524 812 500 26 266 647 1354 494 1030 85 500 80
izquierda without 100160279 N710001170 1524 812 494 26 266 647 1354 494 1030 85 500 80
right integrated 100160300 N710001165 1524 812 500 26 266 647 1354 494 1030 85 500 80
derecha without 100160278 N710001166 1524 812 494 26 266 647 1354 494 1030 85 500 80
left integrated 100160235 N710001172 1676 812 500 26 266 647 1506 494 1182 85 500 80
izquierda without 100160301 N710001171 1676 812 494 26 266 647 1506 494 1182 85 500 80
right integrated 100160292 N710001173 1676 812 500 26 266 647 1506 494 1182 85 500 80
derecha without 100160291 N710001169 1676 812 494 26 266 647 1506 494 1182 85 500 80
left integrated 100160307 N710001164 1828 812 500 26 266 647 1658 494 1334 85 500 80
izquierda without 100160305 N710001168 1828 812 494 26 266 647 1658 494 1334 85 500 80
right integrated 100160306 N710001167 1828 812 500 26 266 647 1658 494 1334 85 500 80
derecha without 100160293 N710001175 1828 812 494 26 266 647 1658 494 1334 85 500 80
DIMENSIONS POSITION
DIMENSIONES POSICIÓN
left integrated 100160234 N710001174 60" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160279 N710001170 60" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
right integrated 100160300 N710001165 60" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160278 N710001166 60" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
left integrated 100160235 N710001172 66" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160301 N710001171 66" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
right integrated 100160292 N710001173 66" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160291 N710001169 66" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
left integrated 100160307 N710001164 71 15/16" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160305 N710001168 71 15/16" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
right integrated 100160306 N710001167 71 15/16" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
derecha without 100160293 N710001175 71 15/16" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
APRON
APRON
60" X 32"
66" X 32"
72" X 32"
60" X 32"
66" X 32"
72" X 32"
KL
SAP KEA A B C D E F G H I J K L
SAP KEA A B C I JDE FGH
100160234_N710001174
100160235_N710001172
100160307_N710001164
100160300_N710001165
100160292_N710001173
100160306_N710001167
100160279_N710001170
100160301_N710001171
100160305_N710001168
100160278_N710001166
100160291_N710001169
100160293_N710001175
DIMENSIONS POSITION
DIMENSIONES POSICIÓN
left integrated 100160234 N710001174 1524 812 500 26 266 647 1354 494 1030 85 500 80
izquierda without 100160279 N710001170 1524 812 494 26 266 647 1354 494 1030 85 500 80
right integrated 100160300 N710001165 1524 812 500 26 266 647 1354 494 1030 85 500 80
derecha without 100160278 N710001166 1524 812 494 26 266 647 1354 494 1030 85 500 80
left integrated 100160235 N710001172 1676 812 500 26 266 647 1506 494 1182 85 500 80
izquierda without 100160301 N710001171 1676 812 494 26 266 647 1506 494 1182 85 500 80
right integrated 100160292 N710001173 1676 812 500 26 266 647 1506 494 1182 85 500 80
derecha without 100160291 N710001169 1676 812 494 26 266 647 1506 494 1182 85 500 80
left integrated 100160307 N710001164 1828 812 500 26 266 647 1658 494 1334 85 500 80
izquierda without 100160305 N710001168 1828 812 494 26 266 647 1658 494 1334 85 500 80
right integrated 100160306 N710001167 1828 812 500 26 266 647 1658 494 1334 85 500 80
derecha without 100160293 N710001175 1828 812 494 26 266 647 1658 494 1334 85 500 80
DIMENSIONS POSITION
DIMENSIONES POSICIÓN
left integrated 100160234 N710001174 60" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160279 N710001170 60" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
right integrated 100160300 N710001165 60" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160278 N710001166 60" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 53" 5/16 19" 7/16 40" 9/16 3" 3/8 19" 11/16 3" 1/8
left integrated 100160235 N710001172 66" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160301 N710001171 66" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
right integrated 100160292 N710001173 66" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
derecha without 100160291 N710001169 66" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 56" 5/16 19" 7/16 46" 9/16 3" 3/8 19" 11/16 3" 1/8
left integrated 100160307 N710001164 71 15/16" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
izquierda without 100160305 N710001168 71 15/16" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
right integrated 100160306 N710001167 71 15/16" 31" 15/16 19" 11/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
derecha without 100160293 N710001175 71 15/16" 31" 15/16 19" 7/16 1" 10" 1/2 25" 1/2 65" 1/4 19" 7/16 52" 1/2 3" 3/8 19" 11/16 3" 1/8
APRON
APRON
60" X 32"
66" X 32"
72" X 32"
60" X 32"
66" X 32"
72" X 32"
KL
SAP KEA A B C D E F G H I J K L
SAP KEA A B C I JDE FGH
100160234_N710001174
100160235_N710001172
100160307_N710001164
100160300_N710001165
100160292_N710001173
100160306_N710001167
100160279_N710001170
100160301_N710001171
100160305_N710001168
100160278_N710001166
100160291_N710001169
100160293_N710001175
100093720
N780000005
100161766
N199999326
100093720
N780000005
100161766
N199999326

4
A
12”
(305mm)
6”
(152mm)
2”
(50mm)
100093720
N780000005
100161766
N199999326
12
34
56

5
A
78
910
11 12

6
12”
(305mm)
6”
(152mm)
2”
(50mm)
12
34
56
100093720
N780000005
100161766
N199999326
B

7
78
910
11 12
B

CITY
60" 49 gal
66" 55 gal
72" 62 gal
Clean the bath with liquid soap and water and soft, non abrasive cloths or sponges.
Never clean with solvents (acetone, alcohol, etc), detergents, or abrasive cloths as these could damage its finish.
To keep the bath looking shiny, use a standard household polish.
CLEANING THE METAL PARTS
Use a soft cloth to clean any metal parts and leave them shiny and scratch free.
_______________________________________________________________________
Pour le nettoyage de la baignoire, employer des savons liquides et de l’eau, et utiliser des éponges ou linges non
abrasifs.
Pour nettoyer, n’utiliser en aucun cas des produits solvants (acétone, alcool, etc.), ni des détergents ou des linges
abrasifs, ce qui endommagerait la surface de la baignoire.
Pour faire briller la baignoire, employer un produit de lustrage ordinaire du commerce.
NETTOYAGE DES ÉLÉMENTS MÉTALLIQUES
Pour nettoyer les éléments métalliques, utiliser un linge doux de manière à ne pas rayer les différentes finitions
métalliques.
_______________________________________________________________________
Para la limpieza de la bañera, utilizar jabones líquidos y agua con paños o esponjas no abrasivos.
Nunca utilizar productos disolventes (acetona, alcohol, etc), ni detergentes o paños abrasivos que dañarían la superficie
de la misma.
Para dar brillo a la bañera, utilizar un pulimento de los habituales en el mercado.
PARTES METÁLICAS
Para la limpieza de las partes metálicas, utilizar un paño suave para no rayar los distintos acabados metálicos.
FDP_30-1-0515-CITY USA-0915-0