Porter 00490-040 Setup guide

INSTALLATION &USAGE MANUAL
SOCCER NET FLOOR ATTACHMENT KIT
FOR NO.00442-000 AND 00448-000
INDOOR SLEEVE-TYPE SOCCER GOALS
No. 00490-040
WARNING
•READ ALL WARNINGS THOROUGHLY BEFORE USING THIS EQUIPMENT.
•FAILURE TO COMPLY WITH THE FOLLOWING INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS
INJURIES AND/OR PROPERTY DAMAGE.
•THE OWNER OF THIS EQUIPMENT IS RESPONSIBLE TO ENSURE THAT ALL INDIVIDUALS FOLLOW THESE
SAFETY AND OPERATING INSTRUCTIONS TO AVOID INJURIES OR PROPERTY DAMAGE. PROPER USE AND
SUPERVISION OF THIS EQUIPMENT IS ESSENTIAL TO HELP REDUCE THE POSSIBILITY OF ACCIDENTS OR
INJURIES.
WARNING
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING TO ASSEMBLE THIS EQUIPMENT. ASSEMBLY
OF THIS EQUIPMENT MUST BE DONE BY PHYSICALLY CAPABLE ADULTS ONLY.
PARTS LIST
Item No. Part No. Quantity Description
1 STAP 00020 003 4 Tension Strap Assembly
2 HDWE 03077 000 4 Floor Insert Nut
INST 00328 080
2000 PORTER ATHLETIC EQUIPMENT COMPANY. ALL RIGHTS RESERVED. 8-1-2000
Upon completion of the assembly/installation of this kit, make sure this
instruction sheet is in the possession of the owner or facility manager, to
save for future reference, and to order replacement parts.
PLAN VIEW OF No. 00490-040
TENSION STRAP ASSEMBLIES
SHOWN ON No. 00442-000 SOCCER GOAL
(SEE PLAN VIEW "A" FOR DIMENSIONAL DETAILS)
"B"
"B"
SEE SECTION "B-B" FOR STRAP ASSEMBLY DETAILS

2
1. Check all parts against Parts List on opposite side to make sure all have been included.
2. Determine the locations of the floor insert nuts (2) – two at each soccer net – according to Plan View “A”. Each insert should be
located approximately 12" behind and 12" to the side of the rear corner of the soccer net.
3. Drill a 1/2" diameter hole, at least 5/8" deep, in the flooring at each of the locations from Step No. 2. See Plan View “A”. Using
a 5/16" allen wrench, screw the floor insert nuts (2) into the holes, until they are flush or slightly below the finished floor.
4. Tension strap assemblies (1) are secured to the floor insert nuts (2) by screwing the handwheel on the tension strap assembly into
the insert. Prior to fully tightening the handwheel, make sure the webbing is pulled in the direction of the corner of the soccer net.
See Section “B-B”.
5. Route the webbing on the tension strap assembly around the bottom hem at the corner of the soccer net. The webbing is then fed
thru the adjustment buckle. Slowly pull on the webbing until the soccer net is taut – pull equally on both straps to keep the soccer
net square. See Section “B-B”.
6. When the soccer goals are not in use, remove the Tension Strap Assemblies from the floor insert nuts and soccer net, to prevent
someone from tripping on the Tension Strap Assemblies.
Porter Athletic Equipment Company
2500 South 25th Avenue, Broadview, IL U.S.A., 60155
Toll Free: [phone] •Phone: [phone] •Fax: [phone]
www.porter-ath.com
SAVE THESE INSTRUCTIONS FOR FUTURE USE
ROUTE WEBBING THRU ADJUSTMENT BUCKLE AS
SHOWN, AND PULL UNTIL SOCCER NET IS TAUT
BOTTOM HEM OF SOCCER NET
Section "B-B"
2
SCREW HANDWHEEL
INTO FLOOR INSERT
UNTIL TIGHT
1
WRAP WEBBING FROM TENSION
STRAP ASSEMBLY AROUND
BOTTOM HEM OF SOCCER NET
SCREW FLOOR INSERT INTO HOLE
(FROM STEP No. 3) UNTIL FLUSH OR
SLIGHTLY BELOW FINISHED FLOOR
FLOOR INSERT LOCATION
DRILL HOLE IN FLOORING - 1/2" DIAMETER x 5/8" DEEP - TWO PLACES AT EACH SOCCER GOAL AS SHOWN
FLOOR INSERT LOCATION
12"
12"
2
OUTLINE OF SOCCER NET
14'-4" (WITH 12' WIDE SOCCER GOALS)
20'-4" (WITH 18' WIDE SOCCER GOALS)
26'-4" (WITH 24' WIDE SOCCER GOALS)
Plan View "A"
FRAME OF SOCCER GOAL
12"
2
12"
VARIES
THIS WARNING IS GIVEN IN COMPLIANCE
WITH CALIFORNIA’S PROPOSITION 65:
WARNING
This product contains chemicals known to the
State of California to cause cancer, birth defects
or other reproductive harm.

3