posame CY-206 User manual

1
BLENDER
CY-206
SKU:PB-002HSH
Instruction Manual

2
TECHNICAL DATA
Model: CY-206
Rated voltage: 120V, 60Hz
Power consumption: 1400W
Protection class: II
SECURITY ADVICE
Carefully read the instruction manual before use and store it.
1. The device is exclusively intended for household use and
additionally for similar uses such as
• in kitchens in stores, offices, or other workplaces,
• for use by guests in lodging establishments (hotels, motels),
private boarding houses, or holiday homes.
2. The shall not be used by children aged from 8 years. Keep the
device as well as its cord away from children. Children are not
allowed to play with the device.
3. This device can be used by people with physical, sensory, or
mental restrictions, by inexperienced people, or by people
without sufficient knowledge of its operation if they are
supervised by a person responsible for their safety or if this
person provided comprehensible instructions on the proper use
of the device as well as the potential dangers involved. Cleaning
and user maintenance shall not be made by children without
supervision.
4. Children shall not play with the appliance.
5. Please store the device, accessories, as well as packaging parts
out of reach of children.
6. Only connect the device to sockets that match the voltage
indicated on the type plate.
7. Never dunk the device, device connector, or cable into water or
another liquid and protect from humidity.
8. The device may not be operated with moist hands. If the device is
wet or moist, please immediately disconnect the power cable.
9. Place the device on a free and level surface. For security reasons,
the high-performance Blender may not be operated on or near
hot surfaces.
10. Only use the device after correct assembly and indoors, it is not
suited for outdoor use.

3
11. Do not hold any objects in the device during operation and never
reach into the Jar with your hand. Risk of injury exists.
12. Only remove the Blender Jar after the motor has come to full rest.
13. Care shall be taken when handling the sharp cutting blades,
emptying the bowl and during cleaning.
14. The knives of the knife inset are sharp! Be careful during cleaning
of the individual parts not to injure yourself.
15. Do not exceed the maximum filling amount.
16. Do not use any sharp or metal objects in the Blender Jar. These
might scratch the Jar. Use plastic or wood spatulas to remove the
ingredients from the Jar.
17. Switch off the appliance and disconnect from supply before
changing accessories or approaching parts that move in use.
18. Always unplug the power cable after use, before cleaning, or in
case of any malfunctions during operation.
19. Never operate the device in combination with accessories of
other devices.
20. Regularly inspect the cable and power cable for wear or damage.
21. Incorrectly performed repairs can endanger the user and void the
warranty. If individual parts are damaged, these need to be
replaced by the manufacturer, an authorized specialist company,
or a similarly qualified person.
22. If the power cable or the device is damaged, it needs to be
replaced/repaired by the manufacturer, customer service, or a
similarly qualified person to avoid danger.
23. Always unplug the device when left unsupervised as well as
before assembly, dis-assembly, and cleaning.
24. Danger! When filling the Blender Jar with hot liquids, hot
splashes or steam might escape.
25. Place the device on an even work surface.
26. CAUTION: In order to avoid a hazard due to inadvertent resetting
of the thermal cut-out, this appliance must not be supplied
through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by the
utility.
27. The appliance is potential injury from misuse and shall be taken
carefully when handling the sharp cutting blades, emptying the
bowl and during cleaning

4
ADVICE: PROTECTION FROM OVERHEATING
The built-in overheat protection monitors the motor temperature
and signals incorrect operation. If need be, the overheat
protection shuts down the motor. Set the speed dial to position
“0FF”. The device can first be operated after the motor has
cooled down.
If the overheat protection signals multiple temperature faults, this
might be the result of the consistency or filling level of the
ingredients. Attempt to reduce the filling volume or to dilute the
contents by adding liquids.
Do not reach into the device during operation – risk
of injury!
Never dunk the device, device connector, or cable
into water or another liquid and protect from humidity.
USING HIGH-PERFORMANCE BLENDER
1
Measuring cup
8
Motor unit
2
Jar lid
9
Speed controller
3
Jar
10
Pulse button
4
Knives with 6-knife system
11
ON / OFF
5
Shock-absorbing sealing
12
Operating buttons

5
6
Motor running gear
13
Tamper
7
Safety switch bar
BEFORE CONNECTING TO POWER
Before connecting to the power, please check whether the type
of supply and the mains voltage match with the details given on
the rating label on the appliance.
Using for the first time, rip off all wrapping paper and plastic bags.
Clean the fittings.
BEFORE USE
Please make sure the jar is well insert into Safety switch bar.
Otherwise, the blender will not work.
SMART SWITCH SYSTEM
The controller of this blender has the functions “M” (Mode),
“ON/OFF”, “Step-less speed levels” and “Pulse”
ON/OFF
Before use the blender, please up the button into “On”
location. And then Blender is in the power standby.
After usage, please press down the button into “Off”
location.
Pulse
Press for blending, remove to stop.

6
Speed controller
Turn the control knob into from min. to max., you could get
different speeds.
Important: The device can only be operated if the controller
is initially set to position “0FF”.
Mode function (M)
When the knob on “M”, 3 buttons are flashing with light.
Press down the button for mode function, the chosen button will
be illuminated. Press the same button again, this function will be
stop. And all buttons will be resuming illuminated.
1) Smoothie function
The high-performance blender starts automatically till to its setting
time finished.
2) Crushed Ice function
The high-performance blender automatically starts: The Blender
chops the ice in intervals separated by short breaks.
3) Soup function
The high-performance Blender starts automatically: Speed will

7
increase till to max speed, will stop by itself.
SECURITY INSTRUCTIONS WHEN USING WITH HOT LIQUIDS
• Be careful when adding and mixing hot ingredients or removing
the lid from the Blender Jar. Steam might escape unexpectedly.
• Never use this device to process boiling liquids. Liquids must be
within 50°，cannot be loaded more than 700ml，its speeds must be in
speed 1-2 and cannot blending more than 4 min.
USING HIGH-PERFORMANCE BLENDER
1. Prepare your ingredients following the recipe. Particularly
heavy or hard ingredients should first be chopped up before
adding them to the Blender Jar.
2. Place the device on an even and dry work surface.
3. Place the Jar on the motor base. Please make sure the jar is
well insert into Safety switch bar. Otherwise, the blender will
not work.
4. Remove the lid and add your ingredients to the Jar. We
recommend adding solid ingredients first and liquid
ingredients afterwards.
5. Make sure that you do not exceed the max. filling level.
6. Place the lid on the Jar and press it down to secure it onto the
Jar. The security contact will not be activated otherwise.
7. Connect the power plug to the connector.
8. To start the high-performance Blender, set the speed using
the controller dial. Select the switch control to start the
high-performance Blender. Attention: The high-performance
Blender only works if the controller dial is initially set to “0FF”.
Dial the controller dial back to “0FF” if the Blender does not
start operation.
Tip: 800 g of chopped carrots can be process at maximum speed
with 1,200 ml of water. Turn the control dial to MAX for two
minutes and subsequently turn it back to “0FF”. Wait for one
minute. Do not repeat more often than four times. Afterwards, let
the motor cool down completely.
9. Set the controller dial to Mode function (M) to select between
the functions “Crushed Ice”, “Smoothie”, and “Soup”. The
button you pressed lights up and the selected programme
starts. Pressing the button again stops the programme and all
buttons will light up again. You can now select a new function.

8
10. You can measure and add further ingredients during
operation through the small opening in the lid, using the
removable measuring cup with 65 ml filling volume.
11. Let the motor wind down completely before removing the
Blender Jar. Never remove it from the base while the Blender
is still in operation or while the motor is still running.
12. If you are finished using the Blender, unplug the device and
clean the Jar and individual parts.
SECURITY INSTRUCTIONS WHEN USING WITH HOT
LIQUIDS
Be careful when adding and mixing hot ingredients or removing
the lid from the Blender Jar. Steam might escape unexpectedly.
Never use this device to process boiling liquids.
Start operating the Blender at low speeds and slowly raise the
speed until you reach the desired speed.
Always firmly close the lid included in delivery to prevent contents,
hot liquids, and hot steam from escaping.
USING THE TAMPER
Remove the measuring cup from the lid and hold the plunger to the
lid opening.
The plunger is only intended to press ingredients towards the blades.
CLEANING AND MAINTENANCE
The Jar should be cleaned and dried as follows after each use.
Not (properly) cleaning the high-performance Blender might
impair its functionality.
1. Before cleaning, power off the device and disconnect the plug
from the connector.
2. Never dunk the housing of the motor base into water.
3. Do not use scratching or abrasive cleaning agents.
4. Only wipe off the housing with a moist cloth.
5. Do not attempt to remove the cutting blades from the Blender
Jar in order to clean them. This might cause the Blender Jar
to leak.

9
6. Remove the Jar from the motor base and remove any
remaining foodstuffs from the Jar. Pay attention to not injure
yourself on the blades when cleaning.
7. Clean the Jar by filling it with 800 ml of warm water and
several drops of mild cleaning agent. Close the Jar with the lid
and set the switch to “max” for 1 min. Repeat the clean
processing for 2 times without clean agent.
8. Allow the Jar and individual parts to dry properly before
reassembling.
The power cable, device plug, and motor should not
come into contact with water. Be careful of the sharp
blades when cleaning the knife insert and Blender
Jar.
TROUBLESHOOTING
Please go through the following steps if the device does not operate
as desired:
1. Inspect whether the instructions in the operating manual were
followed precisely and correctly.
2. Inspect whether the table below offers potential solutions.
3. Inspect whether your fuses are still intact or not.
Problem
Solution
The operating
buttons do not
light up, the
device does not
work.
• Place the mixer Jar onto the motor head and
plug the power cable into the socket.
• Press the Jar down again to reactivate the
security switch.
The operating
buttons light up,
the device does
not work.
• Unplug the power cable from the socket.
• Sure the jar well starts the safety switch of
body.

10
The device stops
after a longer
period of mixing.
• The overload protector protects the motor
from damage.
• Unplug the power cable and let the
high-performance mixer cool down for 30 min.
before connecting It again.
The resulting
mixture is not fine
enough.
• The mixer can be overloaded by too many or
too large ingredients. Try again with a smaller
portion and mix multiple portions if need be.
• Ingredients should be chopped into pieces no
larger than 2 cm.
Ingredients stick
to the Jar or do
not reach the
cutting blades.
• The ingredients might be too large, causing
the ingredients to stick. Ingredients should be
chopped into pieces no larger than 2 cm.
• If necessary, you can set the speeds to
minimum speed and use a plunger to press the
ingredients down towards the cutting blades.
• The mixture might be dry. Add more liquid.
The resulting
mixture is too fine
or too liquid.
• Try to mix for a shorter period.
• Use the “Pulse” function to better control the
mixing process.
Ice is not
chopped up
enough.
• Use smaller pieces of ice (no larger than 2
cm).
• Use the “Crushed Ice” function for easy
operation.

11
Disposal/Recycling
Our products are manufactured with the highest degree of
care and are designed for a long durability. Regular
maintenance and cleaning help to prolong durability. If
the device is defective and cannot be repaired, it must not
be disposed at home.
You must dispose the device at a respective place for recycling of
electronic devices. With correct disposal and recycling you contribute
to preserving the environment.
This appliance complies with the WEEE-Directive 2002/96/EC on the
disposal of electrical and electronic equipment (WEEE).
Get Support: [e-mail]