Postium PRM-902F User manual

LCDRackMonitor
MULTI-CHANNEL LCD RACK MONITOR
User s Manual
,
MO
NIT
O
R
PRM-902F / PRM-102F

Instructions on installation.
Please read the following instructions before installing the monitor.
Avoid installing the monitor in the following places.
• Do not install the monitor near any heat sources such as radiators, heat registers, stoves or
other apparatus that produce heat.
• Do not install the monitor in excessively dusty and humid environments.
• Should any solid object or liquid fall into the monitor, turn the monitor o rst and then
unplug it.
• Do not install the monitor near the source of high frequency or of high electromagnetic
waves and around power lines. This may cause the malfunction and slow down the
performance of the monitor.
• Do not install the monitor in places where extreme environmental changes often occur.
• Do not place the monitor on an unstable cart, stand, or table. It may fall, causing serious
injury to a child or adult and serious damage to the product.
(The monitor should be mounted according to the manufacturer’s instructions, and should
use a mount recommended by the manufacturer such as OB vans.)
• Do not install the monitor in locations where enough space cannot be provided around it as heat
may build up inside, preventing normal operation. The lack of ventilation may damage the
monitor. (Be particularly cautious when the monitor is mounted on the wall)

2
PRM-902F / 102F
Precautions on safety
Precautions on safety
• Do not push any objects of any kind into the monitor through openings as they may touch
dangerous voltage points or short-circuit the parts, which could result in a re or an electric shock.
• Do not drop or place heavy objects on the monitor. A strong impact or force may damage
and break the product.
• Do not use the power cord for AC and DC adaptor at the same time. This may cause the
malfunction of the monitor.
• Remove the AC power from the monitor rst when the monitor needs to be connected for
the update or with external devices. Then, connect the cables and turn the monitor on.
If the monitor is connected with external devices when AC power is connected, it may cause
the malfunction of the monitor.
• Unplug the monitor and contact the A/S team when the monitor emits smoke or
unusual smell and sound.
• Do not attempt to service this monitor yourself, as opening or removing covers may expose
you to dangerous voltages and other hazards. Refer to all service to qualied service personnel,
otherwise the monitor won’t be covered by the warranty.
• The monitor is not covered by the warranty for the problems caused during the process of
calibrating and adjusting the gamma and colors done by users.
First of all, we express our gratitude for your choice to purchase this monitor. Please take your
time reading through the installation and operational instructions. Refer servicing to our
service or sales teams if you have any trouble understanding the manual or experience problems
with the monitor.

3
MULTI-CHANNEL LCD RACK MONITORS
1. Product Overview --------------------------------------------------- 4
2. Features ----------------------------------------------------------------- 4
3. Controls and Functions
3-1. Front Panel ------------------------------------------------------------5
3-2. Rear Panel -------------------------------------------------------------7
3-3. How to save a function on F1, F2 -------------------------------8
4. STATUS DISPLAY --------------------------------------------------------9
5. How to Set OSD Menu ----------------------------------------------10
5-1. VIDEO -----------------------------------------------------------------10
5-2. DISPLAY 1 ------------------------------------------------------------12
5-3. DISPLAY 2 ------------------------------------------------------------13
5-4. COLOR ---------------------------------------------------------------15
5-5. MARKER --------------------------------------------------------------16
5-6. OSD 1 -----------------------------------------------------------------17
5-6. OSD 2 -----------------------------------------------------------------29
5-8. AUDIO ----------------------------------------------------------------20
5-9. GPI ---------------------------------------------------------------------22
5-10.SYSTEM --------------------------------------------------------------23
6. Remote Terminal Assignment -----------------------------------24
6-1. Remote Terminal(RJ-45) Assignment --------------- -------24
6-2. How to Use the Connected GPI Port (RJ-45) --------------24
6-3. Remote Terminal Assignment (GPI Port)-------------------25
7. How to Use the Program Update Port -------------------------25
8. List of Compatible Signal formats (HDMI/COMPOSITE)-----26
8-1.List of Compatible Signal formats (SDI)---------------------27
9. Specications ---------------------------------------------------------28
10. Product Dimensions -----------------------------------------------29
11. Trouble shooting ---------------------------------------------------30
12. Maintenance ---------------------------------------------------------32
13. Possible modication on Product ------------------------------32
14. Caution on operations --------------------------------------------32
15. Caution on installations -------------------------------------------32
Contents
Contents

4
PRM-902F / 102F
1. Product Overview
This product receives the standard 3G/HD/SD-SDI input signals and Composite, Component
and HDMI input signals and displays the images on the LCD Panel with a particular function
which converts HDMI input signal into SDI and SDI input signal into HDMI. As a high
performance color video monitor, this product is suitable for television stations or video
production houses, where precise color reproduction is required.
2. Features
• Color Calibration for optimal luminance, gamma, color temperature
• Supporting 3G-SDI (Level A/B)
• 10-bit Signal Processor
• HDMI-to-SDI & SDI-to-HDMI Converter
• Horizontal/Vertical Level Meters
• Ethernet
• Auto Color Temperature Adjustment
• PIP, PAP(Between analog and digital input)
• USB Memory Update
• Focus Assistance
• False Color
• Waveform
• Vector scope
• Closed Caption (CEA-608/708)
• Time Code(Except 3G Level B)
• 8~16ch Audio Level Meter
• Exposure Range Check
• UMD Mode
• Various Markers (EBU, 4:3, 16:9, 1.85:1, 2.35:1, etc.)
• H/V Delay, Pixel-to-Pixel View, Zero/Under/Over Scan, Blue/Mono
• R/G/B/W Internal Patterns
• Rack Mount
Features

5
MULTI-CHANNEL LCD RACK MONITORS
3. Controls and Functions
3-1. Front Panel (PRM-902F / PRM-102F)
PRM-102F
PRM-902F Front
PRM-102F Front
①②③④⑤⑥⑦⑧
⑩⑪⑫⑬⑭⑮
⑨
PRM-902F / PRM-102F
Controls and Functions

6
PRM-902F / 102F
① --STANDBY : Press for a second to turn on the power and the indicator is on. Press again to turn
o the power.
② --F1/F2 : User-preferred functions are saved on the F1 & F2. The settings for the
functions are managed under System Menu.
③ --WAVE / VECTOR : To display Waveform or Vector Scope. The mode is switched on in the
following order: Waveform -> WFM Parade -> Vector ->WFM / VS ->
WFM Parade / VS -> Wide WFM -> Full WFM -> Full VS -> OFF.
④ --R/G/B/GRAY : To display the pictures in either Red or Green or Blue or Gray(only the
Luminance is displayed). The mode is switched in the following order: Red ->
Green -> Blue -> Gray -> O.
⑤ --MARKER : To activate or deactivate the settings of Marker.
⑥ --SCAN : To select the display mode of Scan screen.
The display modes are Zero Scan, Under Scan, Over Scan and Zoom Scan.
⑦ --HDMI : To select HDIM input.
⑧ --ENTER : To select the categories under OSD MENU.
⑨ --VIDEO Attribute : To open the setting menu for Brightness, Contrast, Chroma, Volume
and Audio.
⑩ --AUDIO LEVEL : To activate Audio Level Meter.
⑪ --H/V DELAY : To check the data carried outside the active range of the input signal.
The delay modes are H Delay, V Delay, H/V Delay and O.
⑫ --ASPECT : To change the size of the screen to 16:9 or to Native Ratio when Analog
(Composite, Component, S-Video), HDMI (SD), SD-SDI (NTSC / PAL), 2Ksf or 2Kp
format is in. This function doesn’t work under the following conditions: 1)
When HD-SDI and HDMI of 1080p, 720p is 16:9 source. 2) Under DVI and VGA channel.
⑬ --ANALOG : To select a desired Analog input.
The inputs are switched in the following order: CVBS1 -> CVBS2 -> CVBS3 ->
SVIDEO -> RGB ->YPbPr -> VGA. OSD LOGO window appears at the top left.
⑭ --SDI-A/B : To select SDI chA or chB input and a separate OSD LOGO
window appears.
⑮ --MENU : To activate OSD Menu.
Controls and Functions

7
MULTI-CHANNEL LCD RACK MONITORS
3-2. Rear Panel (PRM-102F,PRM-902F)
PRM-902F Rear
PRM-102F Rear
PRM-902F / PRM-102F
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
Controls and Functions

8
PRM-902F / 102F
①--AC POWER : Connects the supplied AC power cord.
②--SDI A,B input port (BNC) : Used for the input of HD/SD-SDI signals and for the SDI
signal input which contains audio signals as well.
③--SDI-LOOP OUT port (BNC) : Used for the output of HD/SD-SDI input signals.
There is no output of any kind when the monitor is o
(Active Select Output).
④--HDMI input & output port : Used for the input or output of HDMI signals.
⑤--Component, Composite Input (BNC) : Used for the input of YPbPr, CVBS1,2,3 and R,G,B.
⑥--ETHERNET (RJ-45 Jack) : Used when the monitor needs to be controlled remotely.
⑦--UPDATE Port (RJ-11 Jack) : Used when the program of the monitor needs to be
modied or controlled.
⑧--REMOTE : Used when the monitor is remotely controlled.
⑨--AUDIO :
Used for the input of external audio and for the output of embedded audio signals.
⑩--USB : Used when the rmware program needs to be updated or modied.
3-3. How to save a function on F1, F2
Certain functions can be saved on F1 and F2 on the front of the monitor.
The settings can be managed under System Menu. The following is the list of functions that
can be selected and saved on F1 and F2.
The list of functions that can be assigned.
• FOCUS Assist
• FOCUS Assist BOX Size
• False Color
• Exposure Range Check
• Time code & Tally
• SDI Audio Ch 1/2 &Ch 3/4
• Audio Mute On/O
• Aspect Mode
• Zoom Mode
• 1:1 Scan On/O
• Caption Display
• Time code
• Audio Level Meter
• Freeze On/O
• UMD Display
• Front Button LED On/O
• Video Loss
Controls and Functions

9
MULTI-CHANNEL LCD RACK MONITORS
4. STATUS DISPLAY
This function displays the operational status of the monitor on the screen. Some of the
displays are not supported depending on the product models
CH-1, 3, 5 ~ 15 CH-2, 4, 6 ~ 16
Vector Scope or Waveform Waveform or Vector Scope
1) Audio Level Meter Display : Turns on or o Audio Level Meter Display under Audio MENU.
▶On :
Displays odd-numbered channels on the left and even-numbered channels on the right.
▶O : Turns o the display of level bar.
▶Level Meter Position :
Selects the position of level meter either at the Top or Bottom of the screen.
2) Waveform Monitor / Vector Scope Display : Turns on or o Waveform/Vector Scope
Display using WAVE/VECTOR button on the front.
▶W-FORM / VECTOR Position : Selects the position of the display either at the Left Bottom
or at the Right Bottom by using Knob on the front.
Display position is automatically switched every time the Up or Down button is pressed.
Afterimage of pictures might appear when the signal format is in SDI 2Ksf and the pattern is
either circle or H line, and when there is no change in the pictures for extended time. If this is
the case, change the input signals and the afterimage will disappear.
Under the circle pattern signals in HD-SDI format, certain areas might be displayed as smeared
in the process of scaling.
STATUS DISPLAY