pottery barn kids TREEHOUSE BUNK User manual

Date: 2015-MAY-16 Page 1 of 8
Rev:
pottery barn kids
TREEHOUSE BUNK
www.potterybarnki s.com

Date: 2015-MAY-16 Page 2 of 8
Rev:
WARNING: Failure to follow these warnings an assembly
instructions coul result in serious injury or eath. To help prevent serious
or fatal injuries from entrapment or falls:
• Rea all instructions before assembling bunk be .
• Before each usage or assembly, inspect bunk be for amage har ware, loose joints, missing parts or sharp
e ges. DO NOT use bunk be if any parts are missing or broken.
• DO NOT use substitute parts. Contact pottery barn ki s for replacement parts an an instructional literature if
nee e .
• Follow the information on the warnings appearing on the upper bunk en structure an on the carton. DO NOT
REMOVE WARNING LABEL FROM BED.
• Always use the recommen e size mattress or mattress support, or both, to help prevent the likelihoo of
entrapment or falls.
• Ensure thickness of mattress on upper bunk oes not excee 9 inches an the surface of mattress must be at
least 5 inches (127 mm) below the upper e ge of guar rails.
• Only use the 9" thickness mattress on the lower bunk.
• Ensure both upper an lower bunk are assemble to the highest position when using the pro uct as a bunk be .
• Use only mattress which is 74"-75" long an 37.5"-38.5" wi e on upper an lower bunk.
• Do not allow chil ren un er 6 years of age to use the upper bunk.
• Perio ically check an ensure that the guar rail, la er, an other components are in their proper position, free
from amage, an that all connectors are tight.
• Do not allow horseplay on or un er the be an prohibit jumping on the be .
• Prohibit more than one person on the upper bunk.
• Always use the la er for entering an leaving the upper bunk.
• Use of a night light may provi e a e safety precaution for a chil using the upper bunk.
• Always use guar rails on both long si es of the upper bunk. If the bunk be will be place next to the wall, the
guar rail that runs the full length of the be shoul be place against the wall to prevent entrapment between
the be an wall.
• The use of water or sleep flotation mattresses is prohibite .
• If refinishing, use a non-toxic finish specifie for chil ren's pro ucts.
STRANGULATION HAZARD - Never attach or hang items to any part of the bunk be that are not esigne for
use with the be ; for example, but not limite to, hooks, belts an jump ropes
• This bunk be meets the requirements of ASTM F1427-13
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
04-000044-7

Date: 2015-MAY-16 Page 3 of 8
Rev:
Important Safety Instructions:
• Please rea all instructions carefully before assembling.
• For your safety, assembly by two or more a ults is strongly recommen e .
• Keep instructions for future use.
• Use only ven or supplie har ware to assemble. Using unauthorize har ware coul jeopar ize the structural
integrity of the item.
Pre-assembly:
• Remove all parts an har ware from the box an lay out on a clear carpete or scratch-free work surface, as
this will avoi amaging parts uring assembly. The shipping box provi es an i eal work surface.
• Do not ispose of any packaging or contents of the shipping carton until assembly is complete to avoi
acci entally iscar ing small parts or har ware.
• Use the parts an har ware lists below to i entify an separate each of the pieces inclu e .
• The illustrations provi e allow for easier assembly when use in conjunction with the assembly instructions.
• The use of power tools to ai in assembly is not recommen e . Power tools can amage har ware an split
woo .
• Note: Do not fully tighten all the bolts until all parts are in place. Failure to follow these instructions may cause
the bolts to misalign uring assembly.
PARTS INCLUDED:
(A) En Boar – 2x (D2) Front Right Panel – 1x (G Front Men ing Block – 1x
(B) Front Guar rail – 1x (E1) Rear Left Panel – 1x (H) La er – 1x
(C) Rear Guar rail – 1x (E2) Rear Right Panel – 1x (I) Triangle Block – 4x
(D1) Front Left Panel – 1x (F) Slat Roll – 2x (J) Si e Rail – 2x
E-2.
E-1.
F.
C.
B.
I.
D-2.
D-1.
G.
A.
A.
J. F.
J.
H.

Date: 2015-MAY-16 Page 4 of 8
Rev:
HARDWARE INCLUDED:
(
K
). Allen Key
–
1pc
(
L
)
Bolt 5/
16”
x
110mm
–
2
0
x
(
M
)
Bolt 1/4”
x
78
mm
–
4
x
(N) Bolt 1/4“x54mm – 8x (O) Bolt 1/4“x30mm – 16x (P) Bolt 1/4“x22mm – 4x
(Q) Bolt 1/4“x17mm – 4x (R) Spring Washer 1/4” – 32x (S) Flat Washer 1/4” – 32x
(
T
) Barrel Nut
5/16
”
–
2
0
x
(U) Men ing Plate – 1x
(V) Long Screw 4x30mm – 56x
(W) Short Screw 4x19mm – 2x
Assembly Instruction Steps:
1. Place (6) Barrel Nut (T) onto correspon ing openings on Front Guar rail (B). Insert Bolts (L) into pre- rille
holes on each En Boar (A) from outsi e, as shown below. Connect each en of the Front Guar rail (B) to En
Boar (A) an secure Bolts (L) to Barrel Nuts (T) using Allen Key (K). Repeat with the Rear Guar rail (C).
Loosely tighten with Allen Key.
2. Attach (2) Si e Rail (J) to En Boar s with woo en owels an pre- rille holes aligne as shown below. Insert
(8) sets of Bolt (L) an Barrel Nut (T) to secure.
3. Check alignments before tightening connecting bolts. Do not over tighten.
A.
A.
B.
C.
L.
K.
L.
T.
J.
J.
T.
Tools Require : Philips Hea Screw Driver (not inclu e )
L 20
T 20

Date: 2015-MAY-16 Page 5 of 8
Rev:
4. Sli e a Spring Washer (R) an a Flat Washer (S) onto each Bolt (N). A ttach (4) Triangle Block (I) an insert (8)
Bolts (N) with washers to pre- rille holes as shown below. Tighten all bolts with Allen Key (K) but o not over tighten .
5. Attach Rear Left Panel (E-1) to Rear Guar rail (C) by inserting (4) Bolts (O) with Spring Washer (R) an Flat Washer
(S) using Allen Key (K) as shown in illustration below.
6. Insert (1) Bolt (M) with Spring Washer (R) an Flat Washer (S) to secure Rear Left Panel (E-1) to En Boar post
using Allen Key (K) as seen below. Do not over tighten.
E-1.
K.
M. R. S.
I.
N.
R.
S.
N 8x
R 8x
S 8x
X4
X1
X4
M 1x
O 4x
R 5x
S 5x