Poulan Pro 530164107 User manual

EBVM 215
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
ENGLISH ESPAÑOL FRANÇAIS
530164107 1/24/04
Electrolux Home Products, Inc.
104 Warren Road
Augusta, GA 30907
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2
Copyright E2004 WCI Outdoor Products, Inc.
WARNING:
Read andfollow all Safety Rules and Operating Instructions before
using this product. Read instructions carefully before assembling.
Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual deloperador y siga todas las advertencias e instruc-
ciones de seguridad. Antes de ensamblar el producto lea cuidado-
samenteelinstructivo.Elnohacerlopuederesultarenlesionesgra-
ves.
AVERTISSEMENT:
Veuillez lire le manuel de l’utilisateur et bien respecter tous les
avertissements et toutes les instructions de sécurité. Bien lire les
instructions avantd’assemblerl’outil.Toutdéfautdelefairepourrait
entraîner des blessures graves.
R

2
SAFETY RULES
IMPORTANT WARNINGS AND
SAFETY INSTRUCTIONS
WARNING:
When using electric gardening appliances, basic safety precautions should always
befollowedtoreducetheriskoffire,electricshock,andserious injury. Thewarnings
andsafetyinstructionsinthismanualmustbefollowedtoreducetheriskoffire,elec-
tricshock,or injury,and to providereasonable safety andefficiency inusing thisunit.
Theoperatorisresponsibleforfollowingthewarningsandinstructionsinthismanual
andontheunit. Readtheentireinstructionmanualbeforeassembling andusingthe
unit! Restrict the use of this unit to persons who read, understand, and follow the
warningsand instructionsin this manual and onthe unit.Never allow children touse
this unit. Close attention is necessary when used near children.
OPERATOR SAFETY
SAlways wear safety glasses or similar
eye protection when operating, servic-
ing, orperforming maintenance on your
unit. Wearing eye protection can help to
prevent rocks or debris from being
blown or ricocheting into eyes and face
which can result in blindness or serious
injury.
SAlways wear a respirator or face mask
whenworkingwiththeunitindustyenvi-
ronments.
SDress safely in long pants. Do not go
barefootor wearshort pants or sandals.
SDo not operate the unit when you are
tired, ill,upset,orif you are under thein-
fluence of alcohol, drugs, or medication.
SSecure hair so it is above shoulder
length. Keep loose hair, loose clothing,
fingers, and all other parts of the body
away from openings and moving parts.
Hair, jewelry, loose clothing, or clothing
with loosely hanging straps, ties, tas-
sels, etc., can be caught in moving
parts.
ELECTRICALSAFETY
WARNING: Avoid a dangerous
environment. Toreduce therisk ofelec-
trical shock, do not use in rain, in damp
or wet locations, or around swimming
pools, hot tubs, etc. Do not expose to
snow,rain,orwatertoavoidthepossibil-
ityofelectrical shock. Donothandle ex-
tensioncord plugor unitwith wethands.
SUse only a voltage supply as shown on
the nameplate of the unit.
SAvoid dangerous situations. Do not use
in presence of flammable liquids or
gases to avoid creating a fire or explo-
sion and/or causing damage to unit.
SAvoid dangerous environments. Do not
use in unventilated areas or where dust
or explosive vapors can build up.
STo reduce the risk of electrical shock,
use extensioncords specifically marked
as suitable for outdoor appliances. The
electrical rating of the cord must not be
less than the rating of the unit. The cord
must be marked with the suffix “W-A” (in
Canada, “W”). Make sure your exten-
sion cord is in good condition. Inspect
extension cord before useand replace if
damaged. An undersized extension
cord will cause a drop in line voltage re-
sultinginlossofpowerandoverheating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the
heavier the cord.
(NOTE: The correct size tobe used de-
pending on the cord length is shown in
this manual. See SELECT AN EXTEN-
SION CORD in the ASSEMBLY section).
SInspect the insulation and connectors
on the unit and extension cord before
eachuse. Ifthereisanydamage,donot
use until damageis repaired by yourau-
thorized service dealer. Do not pull or
carry by cord; do notuse cord as a han-
dle, close a door on cord, or pull cord
around sharp edges or corners. Keep
cordawayfromheatedsurfaces. Donot
unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
STie cord to cord retainer and connect to
recessed plug as shown in this manual
to prevent damage to unit and/orexten-
sioncordandtoreducethepossibilityof
the extension cord disconnecting from
the unit during operation.
SDonotuse the unit if theswitch does not
turn the unit on and off properly. Have
the unit repaired by your authorizedser-
vice dealer.

3
SKeeptheextension cordclearofoper-
ator and obstacles at all times. Donot
expose cords to heat, oil, water, or
sharp edges.
SAvoid any body contact with any
grounded conductor, such as metal
fences,or pipes, to avoid the possibility
of electric shock. Don’t handle plug or
unit with wet hands.
SDonotusewithdamagedcordorplug.If
unitisnotworkingasitshould,hasbeen
dropped, damaged, left outdoors, or
dropped into water, return it to your au-
thorized service dealer for repair.
SGround Fault Circuit Interrupter (GFCI)
protectionshould beprovidedonthecir-
cuitoroutlettobeusedforthisunit. Re-
ceptacles are available having built-in
GFCI protection and may be used for
this measure of safety.
SKeep others including children, animals,
bystanders, and helpers a minimum of
30 feet (10 meters) away. Stop the mo-
tor immediately if you are approached.
Do not allow theunit tobe used as atoy.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help
protect against electric shock. Double
insulation construction consists of two
separate “layers” of electrical insula-
tion instead of grounding.
Tools and appliances built with a
double insulation system are not in-
tended to be grounded. No grounding
means is provided on this unit, nor
should a means of grounding be add-
ed to this unit. As a result, the exten-
sion cord used with your unit can be
plugged into any standard 120 volt
electrical outlet. Safety precautions
must be observed when operating any
electrical tool. The double insulation
system only provides added protection
against injury resulting from an internal
electrical insulation failure.
WARNING: All electrical repairs to
this unit, including housing, switch, motor,
etc., must be diagnosed and repaired by
qualified service personnel. Replacement
parts for a double insulated appliance
mustbeidentical to the parts theyreplace.
A double insulated appliance is marked
with the words “double insulation” or
“double insulated”. The symbol
(square within a square) may also be
marked on the appliance. Failure to have
the unit repaired by Sears service person-
nel can cause the double insulation con-
struction to become ineffective and result
in serious injury.
UNIT/MAINTENANCESAFETY
STurn off all controls and allow the motor
to stop before disconnecting the unit
from the power source.
SDisconnect the unit from the power
source when not in use. Do not leave
the unit when it is plugged into outlet.
SDo not set the unit on any surface ex-
cept a clean, hard area while the unit is
running. Debris such as gravel, sand,
dust, grass, etc., could be picked up by
theairintakeand thrownoutthroughthe
discharge opening, damaging the unit,
property, or causing serious injury to by-
standers or operator.
SDo not overreach or use from unstable
surfaces such as ladders, trees, steep
slopes, rooftops, etc. Use extra care
when cleaning on stairways. Keep firm
footing and balance at all times. Keep
hands out of tubes.
SInspect the entire unit before each use
for worn, loose, missing, or damaged
parts. Do not use until the unit is in
proper working order.
SDisconnect unit from power source be-
fore servicing, cleaning, performing
maintenance, or storing.
SThis unit is double insulated. See the
DOUBLE INSULATION CONSTRUCTION
section. Have all internal service per-
formed by qualified service repair per-
sonnel to avoid creating a hazard or
voiding your warranty.
SHave all maintenance other than the
recommended procedures described in
the instruction manual performed by
your authorized service dealer.
SAlways see your authorized service
dealer to replace a damaged impeller.
Partsthat arechipped, cracked,broken,
or damaged in any other way can fly
apart andcause serious injury. Replace
damaged parts before using the unit.
SNever place any object in the air intake
opening as this could restrict proper air
flow and cause damage to the unit.
SNever douse the unit with water or other
liquids orsquirtwith awater hose.Clean
with a damp sponge and mild soap.
See STORAGE.
SCheck air intake openings and tubes
frequently, always with the unit stopped
and power source disconnected. Keep
ventsandtubesfreeofdebriswhichcan
accumulate and restrict proper air flow.
SDo not burn, incinerate, or expose this
unit to extreme heat.
SStore the unit unplugged in a high, cool,
dry, indoor area out of the reach of chil-
dren.

4
SUse only recommended attachments
and replacement parts to avoid creating
a hazard and/or voiding warranty.
SMaintain the unit according to recom-
mended procedures.
SUse only for jobs explained in the OP-
ERATION section of this manual.
BLOWER SAFETY
SUse only in daylight or in good artificial
light.
SInspect the area before using the unit.
Remove all debris and hard objects
such as rocks,glass,wire,etc.,thatcan
ricochet, be thrown, or otherwise cause
injury or damage during operation.
SAvoid accidental starting. Be sure the
switch is in the OFF position and keep
your hand and fingers away from the
switch while connecting the unit to the
power source or when carrying a unit
connected to the power source.
SNever run the unit without the proper
equipment attached. When used as a
blower,alwaysinstall ablowertube.Use
only recommended attachments. Do
notuse with any opening blocked, Keep
free of dust, lint, hair and anything that
may reduce air flow.
SToavoidspreadingfire,donotuseblow-
er near leaf or brush fires, fireplaces,
barbecue pits, ashtrays, etc.
SNever place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and
solid objects such as trees, automo-
biles, walls, etc. The force of air can
cause rocks, dirt, or sticks to be thrown
or to ricochet which can hurt people or
animals, break glass, or cause other
damage.
SNever use for spreading chemicals, fer-
tilizers, or any other substances which
may contain toxic materials.
VACUUM SAFETY
SStop themotorand disconnect thepow-
er source before opening the air inlet
door or attempting to insert or remove
the vacuum tubes. The motor must be
stopped and the impeller blades no
longer turning to avoid serious injury
from the rotating blades.
SHard objects can be thrown through the
collection bag or the housing and be-
come dangerous missiles which can
cause serious injury to the operator or
others.
SWhen using the vacuum attachment,
the unit is designed to pick up dry mate-
rial such as leaves, grass, small twigs,
and bits of paper. Do not vacuum
stones,gravel,metal,brokenglass,etc.,
to avoid severe damage to the impeller.
To avoid the possibility of electrical
shock, do not attempt to vacuum water
or other liquids.
SNever run the unit without the proper
equipment attached. When used as a
vacuum, always install vacuum tubes
andcollectionbagassembly.Makesure
the collection bag assembly is com-
pletely zipped when unit is running to
avoid flying debris. Use only recom-
mended attachments.
SAvoid situations which could set the col-
lection bag on fire. Do not vacuum dis-
carded matches, cigars, cigarettes, or
ash from fireplaces, barbecue pits,
brush piles, etc. To avoid spreading fire,
do not use blower near leaf or brush
fires, fireplaces, barbecue pits, ash-
trays, etc.
SAlways use the collection bag shoulder
strap when vacuuming to avoid loss of
control.
SCheck air intake openings, elbow tube,
and vacuum tubes frequently, always
with the unit stopped and the power
source disconnected. Keep vents and
tubes free of debris which can accumu-
late and restrict proper air flow. Do not
use with any opening blocked, Keep
free of dust, lint, hair and anything that
may reduce air flow.
STANDARDS
This productis listedby UnderwritersLab-
oratories, Inc., in accordance with UL
Standard 1017.
If situations occur which are not covered
in this manual, use care and good judg-
ment. If you need assistance, contact
your authorized service dealer or call
1--800--554--6723. Failure to follow all
Safety Rules and Precautions can result
in serious injury.
SAVE THESE INSTRUCTIONS

5
ASSEMBLY
WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover or attempting toin-
sert or remove the inlet restrictor, blower
tube, or vacuum tubes. The motor must
be stopped and the impeller blades no
longer turning to avoid serious injury from
the rotating blades.
WARNING: If received assembled,
ensure your unit is properly assembled
and all fasteners are secure.
SA standard screwdriver is required for
assembly.
BLOWER ASSEMBLY
NOTE: Assembly instructions for using
your unit as a vacuum follow this section.
Attaching the blower tube
Ifyou have alreadyassembled yourunit
foruse as avacuum, referto thesection
HOW TO CONVERT UNIT FROM VACUUM
USE TO BLOWER USE.
To attach blower tube:
1. Align the grooves on the blowertube
withthegroovesonthebloweroutlet.
2. Pushtheblowertubeontotheblower
outletuntil it snaps intoplace (tubeis
secured by red tube release button).
3. To remove the blower tube, press the
tube release button while pulling on
tube.
Blower Tube
Blower outlet
Tube Release Button
VACUUM ASSEMBLY
NOTE: Assembly instructions for using
yourunitasablowerareexplainedinthe
previous section.
If you have already assembled your unit
for use as a blower, remove the blower
tube.
Remove the inlet restrictor
An inlet restrictor is used when using your
unit as a blower.This restrictoris not used
during vacuum use andmust beremoved
during assembly for vacuum use.
NOTE: Be sure to keep the inlet re-
strictor for using your unit as a blower.
1. Ensure unit is stopped and extension
cord is unplugged.
2. Open the inlet cover by inserting the
tipofascrewdriverintothelatcharea
on the blower unit. Gently tilt handle
ofscrewdriver towardthe frontofthe
unit to release the latch while pulling
up on the vacuum inlet cover with
your other hand.
Vacuum Inlet Cover (closed)
Latch Area
Bottom view
of unit
Latch Area
Impeller
Vacuum Inlet Cover (opened)
3. Turn the inlet restrictor counterclock-
wise and remove it from the unit. Do
not close the inlet door. You will next
attach the vacuum tubes.
Inlet
Restrictor
Vacuum
Inlet Cover
Attaching the vacuum tubes
There are 2 vacuum tubes, an upper
tube and a lower tube. The upper tube
has a vacuum assist handle attached to
oneendandiscutstraightonbothends.
The upper tube attaches to the blower
unit. The lower tube has an angled end
that you point toward the ground during
vacuumuse.Thelowertubeattachesto
the upper tube.
1. Ensure unit is stopped and exten-
sion cord is unplugged.
2. While holding inlet cover open, place
thehooks of thevacuumassisthandle
on the retaining posts of the unit.
3. Raise the tube until it is secured to the
blowerunit by the red inlet cover latch.
Retaining Post
Vacuum Assist Handle
Upper Vacuum Tube
Hook

6
4. To attach the lower vacuum tube to
theuppervacuumtube,firstalignthe
arrowsonthetwotubes.Then,press
thetwotubestogetheruntil thelower
tube is securely seated in the upper
tube (about 3 inches).
Align arrows on upper
and lower tubes
Lower TubeUpper Tube
COLLECTION BAG ASSEMBLY
1. Open the zipper on the collection
bag and insert the elbow tube.
2. Pushthesmall endoftheelbowtube
throughthesmallopeninginthebag.
NOTE: Make sure edge of the small
opening is flush against the flared area
of the elbow tube and the hole for the
tube release button is on top.
Small
Opening
Zipper
Opening
Elbow Tube Tube
Release
Button
Hole
3. Close the zipper on the bag. Make
sure the zipper is closed completely.
4. Align the grooves on the elbow tube
withthegroovesonthebloweroutlet.
5. Push theelbow tube onto theblower
outlet until it snaps into place (elbow
tube is secured by red tube release
button).
ADJUSTINGTHESHOULDERSTRAP
ON THE COLLECTION BAG
1. Carefully loop the shoulder strap
throughthebuckleasshownintheil-
lustration below.
First In
Last In
2. Position the unit on your right-hand
side, blower outlet and bag pointing
toward the rear. Hold the unit in an
upright position with the lower vacu-
um tube on the ground to support it.
3. Place the shoulder strap over your
head and onto your left shoulder.
4. Adjustthestraptoallow afreeflowof
air from the blower. If the collection
bagiskinked,theunitwillnotoperate
properly.
NOTE: The strap is designed to posi-
tion the collection bag on your shoulder
without kinks. The strap is not intended
to support the weight of the unit.
Shoulder strap
on left shoulder
No kinks in bag
allows free air flow
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Stop unit and unplug the extension
cord.
2. Remove the vacuum tubes by insert-
ing the tip of a screwdriver into the
latch area on the vacuum assist han-
dle.Gentlytilthandleof screwdriverto-
ward the front of the unit to release the
latch while pulling up on the vacuum
assist handle with your other hand.
Latch Area
Vacuum
Assist
Handle
3. Install the inlet restrictor that was re-
movedwhenassemblingforvacuum
use.
NOTE: If you are unable to locate the
inlet restrictor, the unit will still operate.
This restrictor improves the blower
function.
4. Remove the collection bag.
5. Close the inlet cover and make sure
it is latched closed.
6. Re-install the blower tube. Refer toAT-
TACHING THE BLOWER TUBE for
instructions on how to attach this item.

7
SELECT AN EXTENSION CORD
Use only a 120 A.C. voltage supply as
shown on nameplate of the unit to
power your blower.
DTo reduce the risk of electrical shock,
this equipment has a polarized plug
(one blade is wider than the other) and
will require the use of a polarized
extension cord. The appliance plug will
fit into a polarized extension cord only
one way. If the plug does not fit fully
into the extension cord, reverse the
plug. If the plug still does not fit, obtain
a correct polarized extension cord. A
polarized extension cord will require
the use of a polarized wall outlet. This
plug will fit into the polarized wall outlet
only one way. If plug does not fit fully
into the wall outlet, reverse the plug. If
it still does not fit, contact a qualified
electrician to install the proper wall
outlet. Do not change the equipment
plug, extension cord receptacle, or
extension cord plug in any way.
The extension cord used to reach the
power source must be:
DSpecifically marked as suitable for out-
dooruse.Thecordmustbemarkedwith
the suffix “W-A” (in Canada “W”).
DHeavy enough to carry full current from
the power source to the unit. Otherwise,
loss of power and overheating can oc-
cur causing damage to unit. Refer to
table for minimum wire gauge recom-
mendations. The cord must be marked
withtheproperwiregauge.(Appropriate
extension cords are available.) Do not
use multiple cords.
DIn good condition. Cord insulation must
be intact with no cracks or deterioration.
Plug connectors must be undamaged.
DO NOT use multiple cords.
MINIMUM WIRE GAUGE
RECOMMENDATIONS
VOLTS 25 FT. 50 FT. 100 FT.
120 16
A.W.G.* 16 A.W.G.*
*American Wire Gauge
14
A.W.G.*
Secure the extension cord to the unit by
threading the cord through the cord re-
tainer (see illustration). Insert the cord
receptacle into the recessed plug.
CAUTION: Failure to use cord retain-
er could result in damage to the unit,
extension cord, or both.
Cord
Retainer
Cord
Receptacle Recessed
Plug
on Unit

8
USING YOUR UNIT
KNOW YOUR ELECTRIC BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Comparethe illustrations to yourunit to familiarize yourself withthe location of
the various controls and adjustments. Save this manual for future reference.
Top Handle
Air Vents
ON/OFF Switch
Inlet Cover
Latch
Rear
Handle
Upper Vacuum Tube
Lower Vacuum Tube
Collection Bag
Blower Tube
Cord
Retainer
Inlet Restrictor
Vacuum Assist Handle
Tube Release Button
Elbow
Tube
Upper Vacuum Tube
Retaining Post
ON/OFF SWITCH
The ON/OFF SWITCH is used to activate
the motor.
INLET COVER LATCH
TheINLETCOVERLATCHisusedtoopen
and close the inlet cover and to secure
the upper vacuum tube to the blower
unit.
BLOWER TUBE
TheBLOWER TUBE is designed to direct
the flow of air.
INLET RESTRICTOR
The INLET RESTRICTOR improves the
blower function.
TUBE RELEASE BUTTON
The TUBE RELEASE BUTTON secures the
blower tube or elbow tube to the blower
unit during operation. Also, pressing the
tube release button allows removal of the
blower tube or elbow tube.
WARNING: You MUST make sure
the tubes are secure before using the
unit.
WARNING: Do not use the unit
without the tubes orcollection bag proper-
ly attached to avoid flying debris and/or
impeller contact which can cause serious
injury. Always wear eye protection to pre-
vent rocks or debris from being blown or
ricocheting into the eyes and face which
can result in blindness or serious injury.
STOPPING YOUR UNIT
Slide the ON/OFF switch to the OFF
position.
STARTING YOUR UNIT
Your unit has two run positions, LOW
and HIGH. Slide the switch to one of
these positions to turn on the unit.
OPERATING POSITION
Blower
Eye Protection
Vacuum
Eye Protection

9
USING YOUR UNIT AS A BLOWER
WARNING: Inspect the area be-
fore using the unit. Remove all debris
and hard objects such as rocks, glass,
wire, etc., that can ricochet, be thrown,
or otherwise cause injury or damage
during operation.
Use your unit as a blower for:
DSweeping debris orgrass clippings from
driveways, sidewalks, patios, etc.
DBlowing grass clippings, straw, or
leaves into piles, or removing debris
from corners, around joints, or between
bricks.
Direct air flow by directing the blower
tube down or to one side. Always work
away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and
moving outward. This will help prevent
an accumulation of debris which could
fly into your face.
Be careful when working near plants.
The force of the air could damage
tender plants.
USING YOUR UNIT AS A VACUUM
WARNING: Do not vacuum
stones, gravel, metal, broken glass,
etc., to avoid severe damage to the im-
peller. To avoid thepossibility ofelectri-
calshock,donotattempttovacuumwa-
ter or other liquids.
Use your unit as a vacuum to pick up
dry material such as leaves, grass,
small twigs, and bits of paper.
DFor best results during vacuum use,
operate your unit at high speed.
DMove slowly back and forth over the
material as you vacuum. Avoid forc-
ing the unit into a pile of debris as
this can clog the unit.
DKeep the vacuum tube about an inch
above the ground for best results.
WARNING: If the unit becomes
clogged,stoptheunitandunplugtheex-
tension cord. Wait until the impeller has
completely stopped turning, then re-
move the vacuum tubes. Carefully
reach into the vacuum opening and
clear out the clogged debris.
MAINTENANCE
WARNING: Disconnect power
source before performing maintenance.
GENERALRECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to opera-
tor abuse or negligence. To receive full
valuefromthewarranty,theoperatormust
maintain unit as instructed in this manual.
Various adjustments will need to be made
periodically to properly maintain your unit.
BEFORE EACH USE
CHECK FOR LOOSE
FASTENERS AND PARTS
SInlet Cover
SBlower Tube
SVacuum Tubes
SCollection Bag
CHECK FOR DAMAGED OR
WORN PARTS
Contact your authorized service dealer
for replacement of damaged or worn
parts.
SON/OFF Switch -- Ensure switch func-
tions properly by moving the switch to
the OFF position. Make sure motor
stops; then restart motor and continue.
SInlet Cover -- Discontinue use of unit if
inlet cover fails to latch properly or if it is
damaged in any way.
AFTER EACH USE
INSPECTANDCLEANUNIT&LABELS
Stop unit and unplug extension cord.
SAfter each use, inspect complete unit
forloose or damaged parts. Clean the
unit using a damp cloth with a mild de-
tergent.
SWipe off unit with a clean dry cloth.
CLEAN COLLECTION BAG
IMPORTANT: THE COLLECTION BAG
MUST BE PROPERLY EMPTIED.
DYou must properly empty and maintain
the collection bag to avoid deterioration
and obstruction of air flow.
DRemove the collection bag from the unit
and empty after each use. Do not store
bag without emptying the bag of all con-
tents (grass, leaves, etc.).
DWash the bag once a year. Remove the
bag fromthe blower and turn the bag in-
side out. Wash the bag with a water
hose. Allow the bag to hang and dry
completely before you reuse the bag.

10
SERVICE
HOW TO REMOVE AN OBJECT
FROM THE AIR INTAKE
WARNING: Stop the unit and dis-
connect from the power source before
openingtheinlet cover. Themotormust
be stopped and the impeller blades no
longer turning to avoid serious injury
from the rotating blades.
1. While holding the inlet cover open,
remove thevacuum tubes. The inlet
cover mustbe held open throughall
remaining steps.
2. Carefully reach into the vacuum
opening and clear out the air intake
area. Clear all debris from impeller.
3. Inspect the impeller for cracks. If
cracked or damaged, do not use the
unit.Havepartsreplacedby yourau-
thorized service dealer. Do not at-
tempt to replace them yourself.
STORAGE
WARNING: Perform the following
steps after each use:
SStop unit and disconnect from the pow-
er source.
SAllow motor to cool before storing or
transporting.
SStore unit with all guards in place. Posi-
tion unit so that any sharp object cannot
accidentally cause injury.
SStore unit unplugged, well out of the
reach of children.
SEASONALSTORAGE
Prepare unit for storage at the end of
the season or if it will not be used for
30 days or more.
If yourblower is to be storedfora period
of time:
SStop unit and disconnect from the pow-
er source.
SClean the entire unitbefore lengthy stor-
age.
SOpen inlet cover and clean any dirt,
grass, or debris that has collected. In-
spect the blower and all tubes. Close
and make sure the cover is latched.
SClean air vents and air inlet of debris.
SStore your unit and extension cord in a
well ventilated area and covered, if pos-
sible, to prevent dust and dirtaccumula-
tion. Do not cover with plastic. Plastic
cannot breathe and may cause con-
densation and eventual rust or corro-
sion.
SCheck entire unit for loose screws. Re-
place any damaged, worn, or broken
parts.
TROUBLESHOOTINGTABLE
SYMPTOM CAUSE REMEDY
Unit fails to
operate. 1. Switch in the OFF position. 2. Extension cord discon--
nected.
3. Circuit breaker tripped, or
fuse blown.
4. Mechanical failure
1. Slide switch to ON position.
2. Reconnect extension cord.
3. Reset circuit breaker or
fuse.
4. Contact your authorized
service dealer.
Unit
vibrates
abnormally.
1. Mechanical failure 1. Contact your authorized
service dealer.
Impeller will
not turn
freely.
1. Debris in air intake area.
2. Mechanical failure. 1. Clean unit. Remove any
debris.
2. Contact your authorized
service dealer.
WARNING: Alwaysstopunitanddisconnectfromthepowersourcebefore
performingalloftherecommendedremediesbelowexceptremediesthatre-
quire unit to be operating.

11
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS,
INC., warrants to the original purchaser
that each new Poulan PROr
rr
rbrand
electric or cordless product is free from
defects in material and workmanship
and agrees to repair or replace under
this warranty any defective Poulan
PROr
rr
rbrandelectricorcordlessproduct
within two (2) years from the original
date of purchase.
If your Poulan PROr
rr
rbrand electric or
cordless product should fail within the
limited warranty period, return it, com-
plete,prepaid,withproofofpurchase,to
the dealer from whom it was purchased
forrepair orreplacement atthe optionof
ELECTROLUX HOME PRODUCTS,
INC.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or the use of accessories
and/or attachments not specifically rec-
ommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Addi-
tionally, this warranty does not cover
partsthat will wearand require replace-
ment with reasonable use during the
warrantyperiod. This warrantydoes not
cover predelivery setup or normal ad-
justments explained in the instruction
manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONSOFINCIDENTALORCONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of ELECTROLUX HOME
PRODUCTS, INC., to continuously im-
prove its products. Therefore, ELEC-
TROLUXHOMEPRODUCTS,INC.,re-
serves the right to change, modify, or
discontinue models, designs, specifica-
tions, and accessories of all products at
any time without notice or obligation to
any purchaser.