Poulan Pro 530164256 User manual

ENGLISH ESPAÑOL FRANÇAIS
DANGER:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
PELIGRO:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
DANGER:
Lirelemanueld’instructionsetbienrespectertouslesavertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PPB300
For Occasional Use Only
Electrolux Home Products, Inc.
104 Warren Road
Augusta, GA 30907
Copyright E2004 Electrolux Home Products, Inc. 530164256 3/11/04
R

2
UL CLASSIFIED PRODUCT NOTICE
Only thefollowingGasolinePoweredCombinationGardeningAppliancepowerheadmodels
andtheirrespectiveattachmentshavebeenClassifiedbyUnderwritersLaboratories,Inc.,in
accordancewith the applicable safety requirements.
Powerhead includingbrushcutter/trimmerattachment PPB300..................
Optional blower attachment PPB3000B...........................................
ThefollowingattachmentisListedbyUnderwriter’sLaboratories,Inc.,inaccordancewithUL
Standard 1602, “Gasoline--Engine--Powered, Rigid--Cutting Member, Edgers and Edge--
Trimmers.”
Optional edger attachment PPB1000E...........................................
SAFETY RULES
WARNING: When using gardening
appliances,basic safety precautionsmust al-
ways befollowed to reducetherisk of fire and
serious injury.
DANGER: This power tool can be dan-
gerous! This unit can cause serious injury in-
cluding amputation or blindness to the operator
and others. The warnings and safety instruc-
tions in this manual must be followed to provide
reasonable safety and efficiency in using the
unit. Theoperatoris responsiblefor followingthe
warnings and instructions in this manual and on
the unit. Read the entire instruction manual be-
fore assembling and using the unit! Restrict the
use of this unit to persons who read, under-
stand, and follow the warnings and instructions
in this manual and on the unit. Never allow chil-
dren to operate this unit.
SAFETY INFORMATION
ON THE UNIT
INSTRUCTION
MANUAL
DANGER: Blade can thrust violently
away from material it does notcut. Blade thrust
can cause amputation of arms or legs. Keep
people and animals 50 feet (15 meters) away.
WARNING: Blade/trimmer line can
throwobjects violently.Youandotherscanbe
blinded or injured. Wear safety glasses and
leg protection.
Leg Guards
Boots
Eye
Protection
ALWAYS WEAR:
Thrown
Objects
WARNING: Hazard zone for thrown
objects. Blade/trimmer line can throw objects vi-
olently. Others can be blinded or injured. Keep
people and animals 50 feet (15 meters) away.
Hazard Zone
50 Feet
(15 Meters)
WARNING: Donotusetrimmerhead
as a fastening device for the blade.
WARNING: The blade continues to
spin after the throttle is released or, engine is
turned off. The coasting blade can throw objects
or seriously cut if accidentally touched. Stop the
blade by contacting the right hand side of the
coasting blade with material already cut.
Stop coasting
blade by contact
with cut material.
OPERATOR SAFETY
SDress properly. Always wear safety
glasses or similar eye protection when op-
erating,orperformingmaintenanceonyour
unit (safety glasses are available). Eye
protection should be marked Z87.
SAlways wear faceor dustmask if operation
is dusty.

3
SAlways wear heavy, longpants, long sleeves,
boots,andgloves. Wearing safety legguards
is recommended.
SAlways wear foot protection. Do not go
barefoot or wear sandals.
SSecure hair above shoulder length. Secure
orremove loose clothing andjewelry orcloth-
ing with loosely hanging ties, straps, tassels,
etc. They can be caught in moving parts.
SBeing fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line/blade.
SStay Alert. Do not operate unit when you are
tired, ill, upset or under influence of alcohol,
drugs, or medication. Watch what you are do-
ing; use common sense.
SWear hearing protection.
SNever start or run the engine inside a
closed roomor building. Breathingexhaust
fumes can kill.
SKeep handles free of oil and fuel.
SAlways use the handlebar and a properly
adjusted shoulder strap with a blade (see
ASSEMBLY).
UNIT/MAINTENANCESAFETY
WARNING: Stopunitanddisconnect
the spark plug before performing mainte-
nance (except carburetor adjustments).
SLook for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep unit in good
working condition.
SThrow away blades that are bent, warped,
cracked, broken, or damaged in any other
way. Replace trimmer head parts that are
cracked, chipped, broken, or damaged in
any other way before using the unit.
SMaintain unit according to recommended
procedures. Keepblade sharp. Keep cut-
ting line at the proper length.
SUse only 0.080!(2 mm) diameter Poulan
PRO"brand replacement line. Never use
wire, rope, string, etc.
SInstall required shield properly before using
the unit. Use the metal shield for all metal
blade use. Use the plastic shield for all line
trimmer use.
SUse only specified blade or trimmer head;
make sure it is properly installed and se-
curely fastened.
SNever start engine with clutch shroud re-
moved.Theclutchcanfly offandcausese-
rious injury.
SBesurebladeortrimmerheadstopsturning
when engine idles.
SMake carburetor adjustments with the low-
er end supported to prevent blade or trim-
mer line from contacting any object. Hold
unit by hand; do not use the shoulder strap
for support.
SKeepothers awaywhen makingcarburetor
adjustments.
SUse only recommended Poulan PROrac-
cessories and replacement parts.
SHave all maintenance and service not ex-
plained in this manual performed by your au-
thorized service dealer.
FUEL SAFETY
SMix and pour fuel outdoors.
SKeep away from sparks or flames.
SUse a container approved for fuel.
SDo notsmoke or allow smokingnear fuelor
the unit or while using the unit.
SAvoid spilling fuel or oil. Wipe up all fuel
spills beforestarting engine.
SMove atleast 10feet (3meters) away from
fueling site before starting engine.
SStop engine and allow it to cool before re-
moving fuel cap.
SEmpty the fueltank beforestoring or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
SStore unit and fuel in area where fuel vapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
SAlways store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAFETY
WARNING: Inspect the area to be
cut beforeeachuse. Remove objects (rocks,
broken glass, nails, wire, string, etc.) which
can be thrown or become entangled in the
blade or trimmer head.
SKeep others including children, animals,
bystanders,andhelpers at least 50feet (15
meters) away. Stop engine immediately if
you are approached.
SAlways keepengineon the right--handside
of your body.
SHold the unit firmly with both hands.
SKeepfirmfootingandbalance.Donotover-
reach.
SKeep blade or trimmer head below waist
level. Do not raise engine above your waist.
SKeep all parts of your body away from
blade, trimmer head, andmuffler when en-
gineisrunning. Ahotmufflercancausese-
rious burns.
SCut from your left to your right. Cutting on
right side of the shield will throw debris
away from the operator.
SUse only in daylight or goodartificial light.
SUse only for jobs explained in this manual.
TRANSPORTINGAND STORAGE
SStop the unit before carrying.
SKeep muffler away from your body.
SAllow theengineto cool andsecure theunit
beforestoringor transportingit in avehicle.
SEmpty the fueltank beforestoring or trans-
portingtheunit.Useupfuelleftin thecarbu-
retor by starting the engineandletting itrun
until it stops.
SStore unit so the blade or line limiter blade
cannot accidentally cause injury. The unit
can be hung by the shaft.
SStore unit out of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnor-
mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in

4
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti--vibration system does not guarantee the
avoidance of these problems. Users who oper-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
SPECIALNOTICE: This unit is equipped
with a temperaturelimiting muffler and spark
arresting screen which meets the require-
mentsofCaliforniaCodes4442and4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equippedwithasparkarrestingscreen. Ifyou
operateinalocalewheresuchregulationsex-
ist, youarelegallyresponsibleformaintaining
theoperatingconditionoftheseparts. Failure
to do so is a violation of the law. For normal
homeowneruse,themufflerandsparkarrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
mufflerbeservicedorreplacedbyyourautho-
rized service dealer.
ASSEMBLY
CARTON CONTENTS
Check carton contents against the following
list:
SPowerhead
SLower attachment (with trimmer head
installed)
SCupped washer
SLarge nut for installing blades
SHex wrench
SHandlebar
SBracket cover
SBracket cover screws (2)
SMetal blade shield
SBlade shield screws (4)
S4--point weed blade
SPlastic shield
SWing nut (screwed onto plastic shield)
SShoulder strap with warning
SContainer of oil
WARNING: Alwaysstopunitanddis-
connectsparkplugbeforeperforminganyas-
sembly procedures.
WARNING: If received assembled,
repeatall steps toensure yourunitis properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue onmuffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
TOOLS REQUIRED
SHex wrench (provided)
SAdjustable wrench
SPhillips screwdriver
INSTALLING BRUSHCUTTER
ATTACHMENT
CAUTION: When installing brushcutterat-
tachment, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
Knob
LOOSEN
TIGHTEN
Shipping
protector
2. Remove shipping protectorfromcoupler.
3. Remove the shaft cap from thebrushcutter
attachment (if present).
4. Position locking/release buttonof attach-
ment into guide recess of coupler.
5. Pushtheattachmentintothecoupleruntil
the locking/release button snaps into the
primary hole.
6. Before using the unit, tighten the knob se-
curely by turning clockwise.
Coupler Primary Hole
Upper
Shaft Locking/
Release
Button Lower
Attachment
Guide Recess
WARNING: Make sure the locking/
release button is locked in the primary hole
andthe knobis securely tightenedbeforeop-
eratingtheunit. Allattachmentsaredesigned
to be used in the primary hole.
For optional attachments, see the AS-
SEMBLY section of the applicable attach-
ment instruction manual.
ATTACHING THE HANDLEBAR
DANGER: To avoid serious injury, the
barrier portion ofthe handlebarmust beinstalled
as shown to provide a barrier between operator
and the spinning blade.
1. Locate the decal on the handlebar. This
decal includes an arrow. Position the
handlebar with the mounting bracket at
the end of the arrow.

5
2. Position the bracket cover over the han-
dlebar.Again make surethe handlebaris
at the end of the arrow.
3. Insert screws and hand tighten only. Be
sure the handlebar is installed correctly;
then, tighten each screw securely with
the hex wrench. Screw
Mounting
Bracket
Handlebar
Bracket Cover
ASSEMBLY OF SHOULDER STRAP
WARNING: Proper shoulder strap
and handlebar adjustments must be made
with the engine completely stopped before
using unit.
1. Insert your right arm and head through
the shoulder strap and allow it to rest on
your left shoulder. Make sure the danger
sign is onyour backandthehookis tothe
right side of your waist.
NOTE: A one-half twist is built in the shoul-
der strap to allow the strap to rest flat on the
shoulder.
2. Adjust the strap, allowing the hook to be
about 6 inches (15 cm) below the waist.
3. Fasten the strap hook to the clamp located
between the trigger handle andthe handle-
bar clamp base and lift the tool to theoper-
ating position.
4. Try on shoulder strap and adjust for fit
andbalancebeforestartingtheengineor
beginning a cutting operation.
NOTE: It may benecessary to relocatethe
shoulder strap clamp on the shaft for proper
balancing of unit.
TO RELOCATE SHOULDER STRAP
CLAMP:
1. Loosen and remove both clamp screws.
2. Place the upper shoulder strap clamp
over the shaft.
3. Position the lower shoulder strap clamp
under the shaft and align the upper and
lower clamp screw holes.
Upper Shoulder
Strap Clamp
Screws
Lower Shoulder
Strap Clamp
4. Insert two screws into the screw holes.
5. Secure shoulder strap clamp by tighten-
ing screws with a hex wrench.
30 inches
(76 cm)
HARNESS
ADJUSTMENT
FOR BALANCE
4 -- 12 inches
(10 -- 30 cm)
above
ground
6 inches
(15 cm)
below
waist
30 inches
(76 cm)
CONFIGURINGYOUR UNIT
You can configure your unit using a cuttinghead
for grass and light weeds, or a weed blade for
cutting grass, weeds, and brush up to 1/2 inch
(1 cm) in diameter. To assemble your unit, go to
the section for the desired configuration andfol-
low the instructions.
ASSEMBLY INFORMATION --
TRIMMER HEAD
TRIMMER
HEAD
NOTE:Remove thebladeandmetal shieldbe-
fore attaching the plastic shield and trimmer
head. To remove blade, align hole in the dust
cup with theholein theside ofthe gearboxby
rotatingthe blade. Insert a small screwdriver
intoalignedholes. Thiswill keeptheshaftfrom
turning while loosening the blade nut. Remove
blade nut by turning clockwise. Remove the

6
screwdriver. Remove both washers and blade.
To remove metal shield, loosen and removethe
four mounting screws. See ATTACHING THE
METAL SHIELD and INSTALLATION OF THE
METALBLADEforillustrations. Besuretostore
all parts and instructions for future use.
ATTACHING THE PLASTIC SHIELD
AND TRIMMER HEAD
WARNING: Theshieldmustbeprop-
erly installed. The shield provides partial
protectionto theoperatorandothers fromthe
risk of thrown objects, and is equippedwith a
line limiter bladewhich cuts excess line tothe
proper length. The line limiter blade (on un-
derside of shield) is sharp and can cut you.
1. Remove wing nut from shield.
2. Insert bracket into slot on shield.
3. Pivot shielduntil boltpassesthroughhole
in bracket.
4. Tighten the wing nut securely.
NOTE: If your unit has a plastic cover over
thethreadsonthethreadedshaft,removethe
coveringtoexposethethreads.Beforeinstal-
lingthetrimmer head,makesurethedust cup
and retaining washer are positioned on the
gearbox as shown below.
Wing Nut
Retaining Washer
Dust Cup
Bracket
Slot
Shield Gearbox
NOTE: Make sure all parts are properly
installed as shown in the illustration before
installing the trimmer head.
5. Align hole in the dust cup with the hole in
the side of the gearbox by rotating the
dust cup.
6. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while tightening trimmer head.
Screwdriver
7. While holding thescrewdriver in position,
thread trimmer head ontothe shaft in the
direction shown on the decal (counter-
clockwise). Tighten until secure.
NOTE: The retaining washer must be posi-
tioned with the raised section facing toward the
gearbox.
ASSEMBLY INFORMATION -- WEED
BLADE
WEED
BLADE
NOTE: Remove the trimmer head and plastic
shield before attaching the metal shield and
installing the weed blade. To remove the trim-
mer head, align holein thedust cup with the hole
in the side of the gearbox by rotating the dust
cup. Insert a small screwdriver into aligned
holes. Thiswill keeptheshaftfromturningwhile
loosening the trimmer head. Remove the trim-
mer head by turning clockwise. Remove the
screwdriver. To removethe plastic shield, loos-
en and remove wing nut. Pivot shield to release
bracket from slot. See INSTALLATION OF
THECUTTINGHEADandATTACHINGTHE
PLASTICSHIELDforillustrations. Besureto
store all parts and instructions for future use.
Never use the trimmer head with the metal
blade installed.
ATTACHING THE METAL SHIELD
WARNING: The metal shield must
be properly installed on the tool anytime the
toolis usedwithablade.Theforwardtip ofthe
metal shield helps to reduce the occurrence
ofbladethrustwhichcancauseseriousinjury
such as amputation to the operator or by-
standers. Failure to install the shield in the
position shown can result in serious injury to
theoperator. The lengthof the shield must be
aligned with the length of the shaft.
1. Place the metal shield under the gearbox,
and align the screw holes.
Shield
Gearbox
2. Insert and thread the 4 mounting screws
through theholes of the gearbox and the
metal shield. Tightenevenly andsecure-
ly with the hex wrench provided.

7
INSTALLATION OF THE METAL
BLADE
WARNING: Wear protective gloves
when handling or performing maintenance on
theblade toavoidinjury. The bladeis sharpand
cancutyouevenwhenitisnotmoving.
WARNING: Do not use any blades, or
fastening hardware other than the washers and
nuts shown in the following illustrations. These
parts must be provided by Poulan/Weed Eater
and installed as shown below. Failure to use
proper parts can cause the blade to fly off and
seriously hurt you or others.
NOTE: The dust cup and retainingwasher are
located onthe gearbox shaftandnotin theparts
bag. All other fasteners mentioned in the follow-
ing assembly steps are in the parts bag.
1. Remove the retaining washer from the
threadedshaft ofthegearbox. Leavethe
dust cup on the shaft.
2. Install the bladeandtheretainingwasher
over the threaded shaft.
3. Make surethe raised partof theretaining
washer is facing the gearbox and the
raised area fits into the hole in the center
of the blade.
4. Slide the blade and retaining washer onto
the shaft of the gearbox.
5. Place the cupped washer onto the shaft.
Makesurethecuppedsideofthewasher
is toward the blade.
6. Install the bladenutby threadingontothe
shaft counterclockwise.
Shield
Blade
Retaining
Washer
Dust Cup
Cupped
Washer Nut
Threaded Shaft
Gearbox
NOTE: Make sure all parts are in place as il-
lustrated, and the bladeis sandwiched between
the dust cup and the retaining washer. There
should be no space between the blade andthe
dust cup or the retaining washer.
7. Align hole in dust cup with hole in side of
gearbox by rotating the blade.
8. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while tightening the blade nut.
Screwdriver
9. TIghtenbladenutfirmly witha wrenchwhile
holding screwdriver in position.
10. Remove the screwdriver.
11. Turn blade by hand. If the blade binds
againsttheshield,or appears to beuneven,
the blade is not centered, and you must re-
install.
NOTE: To remove blade, insert screwdriver
into aligned holes. Unthread the nut and re-
move parts. Be sure to store parts and instruc-
tions for future use.

8
OPERATION
KNOW YOUR UNIT
READ THIS INSTRUCTIONMANUALAND SAFETYRULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit tofamiliarize yourselfwith thelocation ofthe various controls
and adjustments. Save this manual for future reference.
Line Limiter
Blade
Primer Bulb
Handlebar
Starter Handle
Throttle Trigger
Choke
Lever
Shield
Trimmer Head Shaft
Muffler
ON/OFF Switch
Coupler
Blade
ON/OFF SWITCH
The ON/OFF switch is located on the trigger
handle and is used to stop the engine. Move the
switch to the OFF position to stop the engine.
PRIMER BULB
ThePRIMERBULBremovesairfromthecar-
buretor and fuel lines and fills them with fuel.
This allows you tostart theengine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position.Aftertheengineattemptsto start,move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
COUPLER
The COUPLER enables optional attach-
ments to be installed on the unit.
BEFORE STARTING ENGINE
WARNING: Besure toread thefuel
information in the safety rules before you be-
gin. If you donot understandthe safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling. HELPFUL TIP
Toobtainthecorrect oilmix
ratio, pour 3.2 ounces of
2--cycle synthetic oil into
one gallon of fresh gas.
This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brandsynthetic oil is recommended. Mix gaso-
line andoil at aratioof 40:1.A 40:1ratio is ob-
tainedbymixing3.2ounces(95ml)ofoilwith1
gallon(4 liters) of unleadedgasoline. DO NOT
USE automotive oil or marine oil. These oils
will causeenginedamage.When mixing fuel,
followinstructions printedoncontainer. Once
oil is added to gasoline, shake container mo-
mentarily to assurethat thefuel is thoroughly
mixed. Always read and follow the safety
rules relating to fuel beforefueling your unit.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol)canattractmoisturewhichleadsto
separationandformationofacids duringstor-
age. Acidic gas can damage the fuel system
ofanenginewhileinstorage. Toavoidengine
problems, empty the fuel system beforestor-
agefor 30 days or longer. Drain the gas tank,
starttheengineandletit rununtilthefuellines
andcarburetorareempty.Usefreshfuel next
season. Never use engine or carburetor
cleanerproductsinthefueltankorpermanent
damage may occur.
See the STORAGE section for additional in-
formation.
HOW TO STOP YOUR UNIT
STo stop the engine, move the ON/OFF
switch to the OFF position.
SIf engine does not stop, move choke lever
to FULL CHOKE position.

9
Throttle Trigger
ON/OFF
Switch
HOW TO START YOUR UNIT
WARNING: Avoid any contact with
the muffler. A hot muffler can cause serious
burns.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1--800--554--6723.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
Starting Position
Muffler
Choke
Lever
Starter Handle
Primer Bulb
1. Set unit on a flat surface.
2. MoveON/OFFswitch totheONposition.
3. Slowly press the primer bulb 6 times.
4. Move choke lever to FULL CHOKE by
aligning lever with position shown on de-
cal (see illustration below).
Choke
position
decal
5. Squeeze the throttle trigger fully and hold
through all remaining steps.
6. Pull starter rope handle sharply until en-
ginesoundsas ifitis tryingtostart,butdo
not pull rope more than 6 times.
7. As soon as enginesounds as if it is trying
to start, move choke lever to HALF
CHOKE by aligning lever with position
shown ondecal (see illustration below).
Choke
position
decal
8. Pull starter rope sharply until engine runs,
but no more than 6 pulls. If the engine
doesn’t start after 6 pulls (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulls. If the engine doesn’t start, repeat
procedure 2 additional times.
NOTE: If engine still doesn’t start, it is
probably flooded. Proceedto STARTING A
FLOODED ENGINE.
9. Oncetheenginestarts,allowittorun10se-
conds, then move the choke lever to OFF
CHOKE by aligning lever with position
shown on decal (see illustration below). Al-
low the unit to run for 30 more seconds at
OFF CHOKE before releasing the throttle
trigger. NOTE: If engine dies with the
choke lever in the OFF CHOKE position,
movethe choke lever to the HALF CHOKE
position and pull the rope until engine runs,
but no more than 6 pulls.
Choke
position
decal
STARTING A WARM ENGINE
1. MoveON/OFFswitch totheONposition.
2. Move the choke lever to the HALF
CHOKE position.
3. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
5. Allow engine to run 15 seconds, then
movethechokelevertotheOFFCHOKE
position.
NOTE:If engine has not started, pull starter
rope5morepulls.Ifenginestill doesnotrun,it
is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cessfuel.Thiscouldrequirepullingthestarter
handle many times depending on how badly
the unit is flooded.

10
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are: MODEL:
Edger PPB1000E.....................
Cultivator PPB2000T..................
Blower PPB3000B....................
Pruner PP5000P....................
WARNING: Alwaysstopunitanddis-
connectspark plugbeforeremovingorinstal-
ling attachments.
REMOVING TRIMMER ATTACH-
MENT (OR OTHER OPTIONAL
ATTACHMENTS)
CAUTION: When removingor installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
Knob
LOOSEN
TIGHTEN
Upper Shaft
Lower
Attachment
2. Press and hold the locking/release button.
Locking/Release
Button
Coupler Upper Shaft
Lower Attachment
3. While securely holding the engine and
upper shaft, pull the attachment straight
out of the coupler.
INSTALLING OPTIONAL ATTACH-
MENTS
1. Remove the shaft cap from the attach-
ment (if present).
2. Position locking/release buttonof attach-
ment into guide recess of coupler.
3. Pushtheattachmentintothecoupleruntil
the locking/release buttonsnaps into the
primary hole.
4. Beforeusingtheunit,tightentheknobse-
curely by turning clockwise.
Coupler Primary Hole
Upper
Shaft Locking/
Release
Button Attachment
Guide Recess
WARNING: Make sure the locking/
release button is locked in the primary hole
andthe knobis securely tightenedbeforeop-
erating the unit.
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING POSITION
Boots
Heavy,
Long Pants
Eye Protection
ALWAYS WEAR:
Cut from your left to your right.
Hearing
Protection
When operatingunit, clip shoulder strap onto
clamp, stand as shown and check for the fol-
lowing:
SWear eye protection and heavy clothing.
SExtend your left arm and hold handlebar
grip with your left hand.
SHold throttle grip with your right hand with
finger on throttle trigger.
SKeep unit below waist level.
SKeep shoulder strap pad centered on your
left shoulder and danger sign centered on
your back.
SMaintain full weight of tool on your left
shoulder.
SWithout bending over, keep the blade or
trimmer head near and parallel to the
groundandnot crowdedintomaterialbeing
cut.
OPERATING INSTRUCTIONSFOR
USE WITH TRIMMER HEAD
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head. Rocks
or debris can ricochet or be thrown into eyes
and face and cause blindness or other serious
injury.
Beforetrimming,bringenginetoaspeedsuffi-
cient to cut material to be trimmed.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting linewill last longer and will
be less likely to “weld” onto the spool.
Always release the throttle trigger and allow
the engine to return to idle speed when not
cutting.
To stop engine:
SRelease the throttle trigger.
SMove the ON/OFF switch to the OFF posi-
tion.