Power bass PS-WB101 User guide

PS-WB101
PS-WB121
SINGLE SUBWOOFER BASS REFLEX SYSTEM
Application & Enclosure Guide
Please read through this manual to familiarize yourself with your new subwoofer. Should your PowerBass
Autosound Subwoofer System ever require service, you will need to have the original dated receipt.

Congratulations on your purchase of a PowerBass Autosound speaker system. You now own a speaker of
uncompromising design and engineering from a factory that truly believes in the relentless pursuit of perfec-
tion. Incorporating the highest quality parts and state-of-the-art materials, these speakers display the ultimate
balance between high fidelity, performance and long-lasting reliability.
At PowerBass USA, Inc. we are confident you will have many years of outstanding enjoyment from this great
SPEAKER investment. For maximum performance we recommend that you have your new PowerBass Auto-
sound product installed by an Authorized PowerBass Autosound Dealer.
To learn more about PowerBass, please visit us on the World Wide Web at
http://www.powerbassusa.com
∆Warning ∆
Continuous exposure to sound pressure levels in excess of 100 dB can cause permanent hearing loss. PowerBass
Autosound Speakers are capable of producing sound pressure levels well over 170 dB. Please observe all local sound
ordinances while listening to your PowerBass Autosound system. PowerBass USA, Inc. accepts no liability for hearing loss,
bodily injury, or property damage due to the result of use or misuse of this product.
Thank you and Congratulations

POWERBASS AUTOSOUND
LOADED ENCLOSURE FEATURES
Heavy-duty Box Design: The enclosure is constructed from non-resonant 5/8” panels that have been
glued, braced and sealed. Each box is finished in a stylish two tone RFG aviation grade vinyl covering.
Bass Reflex Single Port System: Utilizing a Bass Reflex design offers increased efficiency at low
frequencies. To accomplish this, a flared Venturi port tube is used for exact tuning and virtually zero port
noise (breathing) resulting in clean tight bass.
2-layer Black Ribbed Paper, DDC Finish Cone: The choice of cone materials has everything to do with
the difference between good and great sound. Paper delivers one of the warmest sounds available along
with the DDC (Dynamic Damping Coating) finish to give your music uncompromised fidelity.
BASV High Temperature Voice Coil: These specially designed resin coated high temperature voice
coils measure a full 2-inches in diameter to ensure high power handling and precise linear excursion while
maximizing thermal heat dissipation.
Double Pressed And Treated Foam Surround: The high damping, double rolled foam surround on these
speakers ensure linear travel throughout the entire frequency range resulting in more bass output and
higher efficiency while reducing distortion.
Computer Optimized Acoustic Chamber: Perfectly tuned for the car environment. This box is optimized
for a tight and accurate bass response.
3

SPECIFICATIONS FOR PS SERIES SPEAKER SYSTEM
(Due to Constant Improvements, Specifications and Parameters are subject to change without notice.)
Model Size System
Impedance
Frequency
Response
Sensitivity
1W/1M
Magnet
Size
Voice Coil
Dia.
Power RMS/Peak
PS-WB101 Single 10” 4-ohm 33Hz-150Hz 96dB 40 oz. 2.0” 250W/500W
PS-WB121 Single 12” 4-ohm 30Hz-120Hz 98dB 40 oz. 2.0” 275W/550W
UNPACKING THE ENCLOSURE
Every attempt has been made to transport your new PowerBass Bass Reflex subwoofer system safely.
Carefully unpack the enclosure and inspect it thoroughly for any damage that may have occurred during
shipping. Notify your local PowerBass dealer immediately should you notice any damage prior to installing
the unit. Be sure to keep the carton and packing material until your system is operational. The original
boxes will do the best job of protecting your speaker system if they need to be transported.
INSTALLATION EXPERIENCE
Installation of PowerBass Autosound Speakers requires experience with a variety of mechanical and
electrical procedures. This manual only provides general installation and operating instructions. If you have
any reservations about your installation skills or lack the proper tools, please contact your local PowerBass
Autosound dealer for assistance.
4

ENCLOSURE PLACEMENT TIPS AND RECOMMENDATIONS
Your PowerBass Bass Reflex Subwoofer system accurately reproduces the lowest portion of the audible
frequency range, which is generally considered to be non-directional. As such, the placement within the
vehicle is not as critical to achieve good sound reproduction as with full range systems. Typical locations
include sedan and hatchback trunks and rear cargo areas of vans, mini-vans and utility vehicles.
The following placement recommendations and installation tips are the result of many hours of
development and experimentation. These examples are provided to you as a guide line. Please feel free to
experiment yourself as you may find that other placements can provide you with superior results.
 •Makesureallmovingpartsandfactoryelectricalwiresareoutofyourwayandwillnot
interfere after installation.
 •Leavealittleslackinthewiretopreventpullingorstretching,thisisevenmoreimportantif
the wires will be run under or through the factory interior.
 •Usecabletiesandwireclampstopreventthewiresfromgettingcaughtorshorted.
 •Wedonotrecommendplacingorinstallingloadedenclosureswheretheymightbesubjected
to moisture.
 •Correctsubwooferpolaritymustbeobserved.Thepolaritypositivesideismarkedbya(+)
sign. Subwoofers wired out of phase will produce little bass.
 •Speakerwiresshouldbeelectricallyandphysicallyisolatedfromthevehicleandroutedaway
from any factory wiring that carries high currents or noise (ie, ABS brake systems and engine
computer signals).
 •Usespeakerwirelargeenoughtocarrythefullpowerofyouramplier.14-gaugeorlarger
should be adequate. (Speaker wire not included)
Your PowerBass Bass Reflex subwoofer system needs to be installed some place where it can operate
efficiently and not endanger the occupants of the vehicle.
The location and orientation of your enclosure will affect the quality and quantity of the bass. The port
tube (vent) openings cannot be obstructed. At some frequencies most of the bass will come out of the port
tube. Therefore we recommend you leave at least 3-inches (7.62cm) between the port tube openings and
interior surfaces such as side panels, seats and doors.
If the enclosure is to be mounted all the way in the back of the vehicle, it works best to point the woofer
toward the front of the vehicle. Conversely, if the enclosure is going to be mounted closer to the back seat,
pointing the woofer toward the rear of the vehicle will give you the best results. Even when the enclosure
is placed inside a car trunk with no opening to the passenger compartment, the Bass Reflex design will
produce strong and full bass.
5

WIRING AND CONNECTIONS
The PowerBass Bass Reflex subwoofer system consists of a single 4-ohm voice coil woofer. Check to see
that your amplifier is optimized to drive this load.
A single spring loaded push terminal cup provides a quick and easy connection from your bass amplifier to
your Bass Reflex system
WARNING: Permanent mounting is not only the safest installation, but usually produces the best
sound quality. This custom enclosure is heavy and has a smooth surface finish, which may slide
around during aggressive driving, sudden stops or road vibration. To avoid vehicle damage or
personal injury please ensure that the enclosure is securely mounted to a surface with adequate
strength and rigidity to support it.
1/2”
The push terminal input cup is located on the side of the enclosure (Fig 1). For a bare wire connection,
strip 1/2 inch (12.7mm) of insulation from each of the two conductors of your speaker wire (not included)
to expose bare metal (Fig 2). Carefully twist each of the conductors to eliminate any frayed ends. Push
openbothterminals,lineuptheholes,andinsertthewiresfromyouramplierasfollows:Positivewire(+)
to the Red terminal, Negative wire (-) to the Black terminal. Be careful not to insert the insulated part of
the wire into the hole as this will not give you a good connection.
Fig.1
Fig.2
6

SOUND CHECK
Your PowerBass Bass Reflex Subwoofer system will operate at optimum performance after a break-in
period. Allow the system to play 20 to 30 hours at moderate levels. To sufficiently drive either the Single
Woofer 10 or 12-inch system, we recommend using an amplifier with at least 150 watts RMS mono output.
CAUTION: Damage to the woofers can occur when an amplifier, regardless of its wattage, is made to play
at higher listening levels than its power can clearly produce (usually beyond the “1 to 2 o’clock” position
on the volume control). This results in very high levels of audible distortion. Contrary to popular belief, a
speaker is more likey to be damaged by trying to get too much volume from a low-powered amp than from
a high-powered amp.
NOTE:Lackofbassoutputisusuallycausedbythesubwooferbeingoutofphasewithreferencetothe
rest of the system. In this case reversing the speaker connection from positive to negative on the terminal
cup will correct the problem.
CARE AND CLEANING
The enclosure is constructed of the same non-resonant material used for premium quality home audio
speakers, but covered in vinyl instead of veneer. A damp cloth is best to wipe down any dirt on its surface.
Avoid using strong cleaners that may discolor the vinyl wrap. Never apply water or cleaner to the woofer
cones.
7

WARRANTY NOTES
Should a warranty issue arise with our complete subwoofer enclosure PowerBass will replace the
defective woofers only. Do not send the entire enclosure, unless the enclosure is defective itself.
PowerBass does not warranty the cosmetics of the enclosure once installed in the vehicle.
ENCLOSURE DIMENSIONS AND SPECIFICATIONS
Product Disposal – Certain international, national and/or local
laws and/or regulations may apply regarding the disposal of this prod-
uct. For further detailed information, please contact the retailer where
you purchased this product or the PowerBass Importer/Distributor in
your country.
This manual is the exclusive property of PowerBass USA, Inc.
Any reproduction of this manual, or use other than its intentions is strictly prohibited without the express consent of PowerBass USA, Inc.
Copyright 2016 PowerBass USA, Inc.
PS-WB121
12.25”
(311mm)
11.4”
(290mm)
18.75” (476mm)
17” (432mm)
14.4”
(366mm)
13.75”
(349mm)
13.5” (343mm)
12.25” (311mm) PS-WB101
Mounting Bracket
Mounting Bracket

POWERBASS AUTOSOUND LIMITED WARRANTY POLICY
PowerBass USA, Inc. offers limited warranty on PowerBass products under normal use on the following terms:
PowerBass Autosound Speakers are to be free of defects in material and workmanship for a
period of one (1) year.
This warranty applies only to PowerBass products sold to consumers by Authorized PowerBass Dealers in the United States
of America. Products purchased by consumers from a PowerBass dealer in another country are covered only by that coun-
try’s Distributor and not by PowerBass USA.
This warranty covers only the original purchaser of PowerBass product. In order to receive service, the purchaser must
provide PowerBass with a valid purchase receipt from an authorized reseller stating the consumer name, dealer, product
and date of purchase.
Products found to be defective during the warranty period will be repaired or replaced (with a product deemed to be equiva-
lent) at PowerBass’s discretion and will not be liable for incidental or consequential damages. PowerBass will not warranty
this product under the following situations:
• Speakers received with bent frames or water damage
• Abuse such as holes in the cone, surround or ripped spider
• Voice coil damage due to amplier clipping or distortion
• Product that has not been installed according to this owners manual
Any implied warranties including warranties of fitness for use and merchantability are limited in duration to the period of
the express warranty set forth above. Some states do not allow limitations on the length of an implied warranty, so this
limitation may not apply. No person is authorized to assume for PowerBass any other liability in connection with the sale
of this product.
Please call [phone] for PowerBass Customer Service. You must obtain an RA# (Return Authorization Number)
to return any product to PowerBass. The RA number must be prominently marked on the outside of the shipping
carton or the delivery will be refused. Please pack your return carefully; we are not responsible for items damaged in
shipping. Return the defective product along with a copy of the original dated retail sales receipt, plus $12.00 for handling
and diagnostic evaluation to:
PowerBass USA, Inc.,
Attn: Returns (RA#__________)
2133 South Green Privado, Ontario, CA 91761
Residents of HI, AK and US territories will be charged for return shipping. All inquires regarding service and warranty should
be sent to the above address.
Removed or altered serial numbers will void this warranty
NOTE: Return only the part(s) that must be repaired or replaced. Do not send the entire system! It
will only cause unnecessary delays and may result in damage that is not covered by this warranty.

PowerBass Autosound – A division of PowerBass USA, Inc.
2133 South Green Privado – Ontario, CA 91761
Tel. [phone] – Fax [phone]
www.powerbassusa.com