Power-flo PFS411HTCE-2 Series Guide

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
0.4 HP • 1750 RPM • 60 Hz
Submersible Euent,
Sump & Sewage Pump
High Temperature
ISP No: PFS411HTCE-2 - 9/2020
INSTALLATION, SERVICE & PARTS MANUAL
Series:
PFS411HTCE-2

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
2
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps
General Safety Information
Serial #
® Power-Flo is a registered trademark of Power-Flo Technologies Inc.
Other brand and product names are trademarks or registered trademarks of their respective holders.
Alteration Rights Reserved. 4/11, 5/12, 9/2020
Before installation, read the following
instructions carefully. Failure to follow
instruction and Safety information could
cause serious bodily injury, death and/or
property damage. Each Power-Flo pump is
individually factory tested to insure proper
performance. Closely following these
instructions will eliminate potential operating
problems, assuring years of trouble-free
service.
“Danger” indicates
an imminenty
hazardous situation which, if not avoided,
WILL result in death or serious injury.
“Warning” indicates
an imminenty
hazardous situation which, if not avoided,
MAY result in death or serious injury.
“Caution” indicates
an potentially
hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
IMPORTANT - Power-Flo Pumps and
Systems is not responsible for losses, injury
or death resulting from failure to observe
these safety precautions, misuse, abuse or
misapplication of pumps or equipment.
ALL RETURNED
PRODUCTS MUST BE
CLEANED, SANITIZED,
OR RECONTAMINATED
PRIOR TO SHIPMENT, TO
INSURE EMPLOYEES WILL NOT BE EXPOSED
TO HEALTH HAZARDS IN HANDLING SAID
MATERIAL. ALL APPLICABLE LAWS AND
REGULATIONS SHALL APPLY.
Installation, wiring,
and junction
connections must be in accordance with
the National Electric Code and all applicable
state and local codes. Requirements may
vary depending on usage and location.
Installation and
servicing is to be
conducted by qualied personnel only.
Keep clear of suction
and discharge
openings. Do not insert ngers in
pump with power connected.
Always wear eye
protection when
working on pumps. Do not wear loose
clothing that may become entangled in
moving parts
Pumps build up heat
and pressure during
operation. Allow time
for pumps to cool
before handling or
servicing.
This pump is not
intended for use in
swimming pools or water
installations where human
contact with pumped uid. Pumps
when used as a decorative water fountain
pump MUST be used in circuit protected by
a Ground Fault Interrupter.
Risk of electric shock.
To reduce risk of
electric shock, always disconnect
pump from power source before
handling. Lock out power & tag.
Do not us these
pumps in water
over 200˚F. Do not exceed manufactures
recommended maximum performance, as
this could cause the motor to overheat.
Do not lift, carry or
hang pump by the
electrical cables. Damage to the
electrical cables can cause shock,
burnes or death. Never handle
connected power cords with wet hands. Use
appropriate lifting device.
Sump and sewage
pumps often handle
materials which could cause illness or disease.
wear adequate protective clothing when
working on a used pump or piping. Never
enter a basin after it has been used.
Failure to permanently
ground the pump,
motor and controls before
connecting to power can cause
shock, burns or death.
These pumps are NOT
to be installed in
locations classied as hazardous in
accordance with the National
Electric Code, ANSI/NFPA 70.
The Uniform Plumbing
Code (UPC) states that
sewage systems shall have an audio and
visual alarm that signals a malfunction of
the systems that is required to reduce the
potential for property damage.
IMPORTANT!
Prior to installation, record Model
Number, MFG Date, Amps, Voltage, Phase
and HP, from pump name plate for future
reference. Also record the Voltage and
Current Readings at Startup:
1 Phase Models
Amps: Volts:
Model Number: ____________________
MFG Date: ________________________
PHASE: ______ HP: _________________
WARNING:
CANCER AND REPRODUCTIVE HARM-
WWW.P65WARNINGS.CA.GOV

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
3
DISCHARGE 2” NPT, Female, Vertical
LIQUID
TEMPERATURE 200°F (93°C) Continuous High Temperature
SOLIDS HANDLING 1/2” Solids through strainer.
2” without strainer
VOLUTE Cast Iron, Class 30
MOTOR HOUSING Cast Iron, Class 30, w/removable upper
chamber for ease of capacitor and cord
replacement
IMPELLER 2 Vane, open with pump out vanes on back side
Material: Cast Iron, Class 30
SHAFT Stainless Steel
SEAL PLATE Cast Iron, Class 30
SQUARE RINGS Buna-N
HARDWARE Stainless Steel
PAINT Powder Coated - Industrial Grade
SEAL
Inboard Single Mechanical, Oil Filled ,
Material: Type 21, Silicon Carbide/Buna-N
Secondary Exclusion Seal
POWER CORD 15 Ft. Cord, Plug on 115 Volt, Pressure
Grommet for Sealing and Strain Relief
MOTOR
Oil Filled, Squirrel Cage Induction
Class H Insulation, Vacuum Pressure
Impregnated (VPI)
SINGLE PHASE
Permanent Split Capacitor (PSC),
Includes Overload Protection in Motor:
115v, 50A, Trip O Temp. 293°F (145°C),
Closing Temp. 226°F (108°C)
UPPER BEARING Single Row, Ball, Oil Lubricated
LOWER BEARING Single Row, Ball, Oil Lubricated
SLUDGE STRAINER Bar Strainer with 3” extended feet
LEVEL CONTROL
Wide Angel, High Temperature Mechanical
Float. 15Ft. cord with piggy-back plug.
Normally Open (N/O)
Specications - High Temp
MODEL HP Hz Volts/
Ph RPM Full Load Amps
Locked
Rotor Amps
NEMA Start
Code
Winding Resistance
MAIN -- START
Cord
Type
Cord
Size
Cord
O.D.
PFS411HTCE-2 4/10 60 115/1 1750 10.0 24.5 N1.6 -- 18.5 SJOOW 16/3 0.325
Series: PFS411HTCE-2
4/10 HP • 1750 RPM • 60 Hz
High Temperature
Submersible Sewage Pump
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
4
Dimensions & Performance - High Temp
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
5
Minimum
Submergence Level
Bottom of Feet
9” for HTCE
Receiving Inspection
Upon receiving the pump, it should be
inspected for damage or shortages.
If damage has occurred, le a claim
immediately with the company that
delivered the pump. If the manual is
removed from the packaging, do not
lose or misplace.
Storage
Any product that is stored for a period
longer than six (6) months from the
date of purchase should be bench
tested prior to installation. A bench
test consists of, checking the impeller
to assure it is free turning and a run
test to assure the motor (and switch
if provided) operate properly. Do not
pump out of liquid.
Controls
Manual models require a separate
approved pump control device or panel
for automatic operation. Be sure the
electrical specication of the control
selected properly match the electrical
specications of the pump.
Submergence
The pump should always be operated in
the submerged condition. The minimum
sump liquid level should never be less than
above the pump’s volute (See Figure 1).
Liquid Level Controls
Typical Discharge Pipe Mounted:
Refer to Figure 2 below which shows a
typical installation of a 1 phase 115 volt
pump using a level control mounted
to the pump with a piggy-back plug.
The level control should have adequate
clearance so it cannot hang up in it’s
swing and that the pump is completely
submerged when the level control is in
the “O” mode. By adjusting the cord
tether the control level can be changed. Automatic: Plug oat cord into GFI outlet, then
plug pump cord into oat cord.
Manual: Plug pump cord directly into GFI
outlet.
Level Control Basic Instructions:
Plug the level control plug into the GFI
receptacle, then plug the pump into the
piggy-back plug (See Figure 3). One cycle
of operation should be observed, so that
any potential problems can be corrected.
It is recommended that the level control
oat should be set to insure that the liquid
in the sump never drops below the top
of the motor housing or a minimum level
of 6 inches (9inches on HTCE) above the
basin oor.
Installation
These pumps are recommended for
use in a sump or basin. The sump
or basin shall be sealed and vented
in accordance with local plumbing
codes. This pump is designed to pump
euent or wastewater, nonexplosive
and noncorrosive liquids and shall
NOT be installed in locations classied
as hazardous in accordance with the
National Electrical Code (NEC) ANSI/
NFPA 70 or Canadian Electric Code
(CEC). The pump should never be
installed in a trench, ditch, or hole with
a dirt bottom. The legs will sink into
the dirt and the suction will become
plugged.
Figure 1
Receiving & Installation
Recommended
Submergence Level
Typical Installation with Wide Angle
Level Control
Figure 2
Figure 3
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
6
The installation should be at a sucient
depth to ensure that all plumbing is
below the frost line. If this is not feasible,
remove the check valve and size the
basin to accommodate the additional
backow volume.
Discharge Piping
Discharge piping should be as short
as possible and sized no smaller than
the pump discharge. Do not reduce
the discharge pipe size below that
which is provided on the pump. Both
a check valve and a shut-o valve are
recommended for each pump. The
check valve is used to prevent backow
into the sump. The shut-o valve is
used to manually stop system ow
during pump servicing.
Electrical Connections
Power cable:
The power cable mounted to the pump
must not be modied in any way except
for shortening to a specic application.
Any splice between the pump and the
control panel must be made in
accordance with the electric codes. It is
recommended that a junction box, if used,
be mounted outside the sump or be of
at a minimum Nema 4 construction if
located within the wet well. DO NOT USE
THE POWER CABLE TO LIFT PUMP.
Always rely upon a Certied Electrician
for installation.
Overload Protection:
Single Phase - The stator in-winding
overload protector used is referred to
as an inherent overheating protector
and operates on the combined eect of
temperature and current.
This means that the overload protector
will trip out and shut the pump o if the
windings become too hot, or the
load current passing through them
becomes too high.
IMPORTANT ! - The overload will then
automatically reset and start the pump
up after the motor cools to a safe
temperature. In the event of an overload,
the source of this condition should be
determined and corrected immediately.
WARNING! - DO NOT LET
THE PUMP CYCLE OR RUN IF
AN OVERLOAD CONDITION
OCCURS !
Wire Size:
If longer power cable is required consult
a qualied electrician for proper wire
size.
Pre-Operation
1. Check Voltage and Phase
Compare the voltage and phase
information stamped on the pump
name plate.
2. Check Pump Rotation - Improper
motor rotation can result in poor
pump performance and can damage
the motor and/or pump. Incorrect
rotation for Single-Phase pumps is
unlikely. If the rotation is incorrect
contact factory.
3. Name Plate - Record the information
from the pump name plate to
drawing in front of manual for future
reference.
4. Insulation Test - An insulation
(megger) test should be performed
on the motor. Before the pump is put
into service. The resistance values
(ohms) as well as the voltage (volts)
and current (amps) should be
recorded.
5. Pump-Down Test - Be sure pump
has been properly wired, lowered into
the basin, sump or lift station, check
the system by lling with liquid and
allowing the pump to operate through
its pumping cycle. The time needed to
empty the system, or pump-down
time along with the volume of water,
should be recorded.
Maintenance
No lubrication or maintenance is required.
Perform the following checks when pump
is removed from operation or when pump
performance deteriorates:
a). Inspect motor chamber for oil level
and contamination.
b). Inspect impeller and body for
excessive build-up or clogging.
c). Inspect motor and bearings.
d). Inspect seal for wear or leakage.
Servicing
NOTE: Item numbers in ( ) refer to Figure 5.
Cooling Oil - Anytime the pump is
removed from operation, the cooling oil
in the motor housing should be checked
visually for oil level and contamination.
To check oil, set unit upright. Remove pipe
plug from housing or remove capscrews
(21), washers (22) and remove upper
motor housing (17), do not damage o-ring
(9). With a ashlight, visually inspect the
oil in the housing to make sure it is clean
and clear, light amber in color and free
from suspended particles. Milky white oil
indicates the presence of water. Oil level
should be just above the motor when
pump is in vertical position.
Installation & Service
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
7
Oil Testing
• Drain oil into a clean, dry container by
placing pump on it’s side, remove pipe
plug, from housing.
• Check oil for contamination using an
oil tester with a range to 30 Kilovolts
breakdown.
• If oil is found to be clean and
uncontaminated (measuring above
15 KV. breakdown), rell the housing.
• If oil is found to be dirty or
contaminated (or measures below
15 KV. breakdown), the pump must
be carefully inspected for leaks at the
shaft seal, cable assembly, square ring,
o-ring and pipe plug, before relling with
oil. To locate the leak, perform a pressure
test.
After leak is repaired, dispose of old oil
properly, and rell with new oil.
Pressure Test (If oil has been drained)
Remove pipe plug from housing. Apply
pipe sealant to pressure gauge assembly
and tighten into hole. Pressurize motor
housing to 10 P.S.I. Use soap solution
around the sealed areas and inspect joints
for “air bubbles”.
If, after ve minutes, the pressure is still
holding constant, and no “bubbles” are
observed, slowly bleed the pressure and
remove the gauge assembly. Replace
oil. Leek must be located and repaired if
pressure does not hold.
Pressure Test (If oil has NOT been
drained) - Oil should be at normal level.
Remove pipe plug from housing. Apply
pipe sealant to pressure gauge assembly
and tighten into hole. Pressurize motor
housing to 10 P.S.I. Use soap solution
around the sealed areas above the oil
level and inspect joints for “air bubbles”.
For sealed areas below oil level, leeks will
seep oil. If, after ve minutes, the pressure
is still holding constant, and no “bubbles”
/oil seepage is observed, slowly bleed the
pressure and remove the gauge assembly.
Replace oil. Leek must be located and
repaired if pressure does not hold.
Pressure builds up extremely
fast, increase pressure by
“TAPPING” air nozzle. Too much
pressure will damage seal. DO
NOT exceed 10 P.S.I.
Oil Replacement - Set unit upright and
rell with new cooling oil as per table. Fill
to just above motor, but below capacitor
as an air space must remain in the top
of the housing to compensate for oil
expansion. Apply pipe thread compound
to threads of pipe plug then assemble to
housing.
DO NOT overfill oil. Overfilling
of housing with oil can create
excessive and dangerous hydraulic
pressure which can destroy the
pump and create a hazard.
Overfilling oil voids warranty.
Cooling Oil - 40.6 oz
Recommended Supplier/Grade
BP Enerpar SE100
Conoco Pale Parafn 22
Mobile D.T.E. Oil Light
Shell Canada Transformer-10
Texaco Diala-Oil-AX
Disassembly
Impeller, V-ring and Volute:
1. Disconnect power.
2. Remove legs (33) and remove strainer
(32).
3. Remove cap screw (27) and washers
(28) vertically lift motor, housing and seal
plate assembly from volute (1). Clean out
volute (1) if necessary.
4. Inspect gasket (2) and replace if cut or
damaged.
5. Clean and examine impeller (31), for
cracks or breakage and replace if required.
To remove impeller (31), place a at
screwdriver in the slot of the end of the
shaft to hold the shaft stationary while
unscrewing the impeller (31).
6. Check v-ring (29) and remove if
damaged.
Power Cord & Motor:
7. Remove pipe plug (16) and drain oil
from housing.
8. Remove gland nut (15E), from upper
motor housing (17). Remove capscrews
(21) and washers (22) and lift o upper
motor housing (17) and o-ring (9). Pull
cord through and disconnect the wires
from the terminals on power cord (15).
9. Remove screws (4) and lift motor
housing and motor from seal plate (8).
Service
Figure 4
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
8
10. Remove o-ring (3), replace if damaged,
11. Check motor capacitor (11) with
an Ohm meter by rst grounding the
capacitor by placing a screwdriver across
both terminals and then removing
screwdriver. Connect Ohm meter (set
on high scale) to terminals. If needle
moves to innity (∞) then drifts back,
the capacitor is good. If needle does not
move or moves to innity (∞) and does
not drift back, replace capacitor (11).
12. Inspect motor winding for shorts and
check resistance values. Check rotor for
wear. If rotor or the stator windings are
defective, the complete motor must be
replaced.
Shaft Seal:
13. Remove snap ring (6) from seal plate
(8). Remove shaft and motor from seal
plate (8).
14. Remove seal’s (26) rotating member,
spring and retaining ring from seal plate
(8). Examine all seal parts, if seal faces
show signs of wear, uneven wear pattern,
chips or scratches replace entire seal.
DO NOT interchange seal components,
replace the entire shaft seal (26).
If replacing seal, remove stationary by
prying out with at screwdrive.
Bearings:
15. Examine lower bearing (5), and upper
bearing (23), if replacement is required,
remove by using a wheel puller.
Reassembly
Bearings:
1. Press bearings (5) and (23) onto shaft.
IMPORTANT! - All parts must be
clean before reassembly.
Handle seal parts with extreme
care. DO NOT damage lapped
surfaces.
Shaft Seal:
2. Clean seal cavity in seal plate (34) and
oil. Press seal’s (26) stationary member
rmly into seal plate (8), use a seal tool
or pipe. Nothing should come in contact
with the seal face except the seal tool. Be
sure the stationary is in straight.
3. Place seal’s retaining ring onto shaft.
Lightly oil (Do not use grease) shaft and
inner surface of bellows.
4. With lapped surface of seal’s rotating
member facing outward, slide over shaft
using a seal tool, being carefull not to
damage seal face. Make sure spring is
seated in retaining ring and spring is
lined up on rotating member and not
cocked or resting on bellows tail.
Motor:
5. Slide rotor/shaft with bearings and seal
parts (26) into seal plate (8) until bearing
seats into seal plate. Install snap ring (6)
into seal plate (8).
6. Place spring washer (24) onto bearing
(23) and lower motor housing (25) with
motor stator onto seal plate (8).
7. Place screws (4) through seal plate
(8) into housing (25) and torque to 10
Ft-lbs.
8. Assemble capacitor (11) with bracket
(10) onto motor housing (25). Place
o-ring (9) on motor housing (25).
Power Cord:
9. Check power cord (15) for cracks or
damage and replace if required.
10. Place power cord (15) with nylon
housing (15D), ring (15C), Kellum grip
(15F) and gland nut (15E) into upper
housing (17) and reconect wires to cord
set.
11. Set upper motor housing (17) onto
motor housing (25) being careful not to
damage o-ring (9). Place capscrews (21)
and washer (22) through upper housing
(17) into motor housing (25) and tighten.
12. Tighten gland nut (15E) to 17.5 ft/lbs.
Impeller, V-ring and Volute:
13. Position v-ring (29) into seal plate (8)
until seated.
14. Clean the threads with thread locking
compound cleaner. Apply removable
Loctite® 242 or equivalent to shaft
threads. Screw impeller (31) onto the shaft
hand tight while using a screwdriver in
the slot at the end of the shaft to hold it
stationary. Rotate impeller to check for
binding.
15. Position gasket (2) on volute ange
and position impeller and motor housing
assembly on volute (1).
16. Place lock washers (28) on cap screws
(27) and screw into volute (1). Torque
to 25 ft/lbs. Check for free rotation of
impeller.
17. Re-attach strainer (32) and legs (33).
18. Rell with cooling oil. 40.6 oz (1.2 liters)
Float Switch:
19. Attach oat (34) to upper motor
housing (17) with cable clamp (35) and
screw (36). Leave a minimum tether of
3.50 inches from cable clamp to end of
oat. (see Fig. 5 on page 9 and also page
4)
Service
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
9
Repair Parts
For Repair Part Please supply: Model Number and MFG Date as shown on
Name Plate, and Part Description and Part Number as shown on Parts List.
Figure 5
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
10
Repair Parts For Repair Part Please supply: Model Number and MFG Date as shown on
Name Plate, and Part Description and Part Number as shown on Parts List.
ITEM QTY DESCRIPTION Part No.
1 1 Volute ---
2 1 Gasket PF068984A
31 Square ring PF019289A
4 2 Screw, Stainless - Torque to 10 Ft-Lbs ---
5 1 Bearing, 6203 - Lower ---
6 1 Snap Ring ---
7 1 Motor (rotor/stator) ---
8 1 Seal Plate ---
9 1 O-ring ---
10 1 Capacitor bracket ---
11 1 Capacitor, 20 mfd/250V ---
12 1 Cord clamp ---
13 2 Screw ---
14 1 Handle ---
15 1 Power Cord 15 Ft. 16/3c SJOOW (includes 15A - 15G PF100502K
15A 1 Terminal Pin Holder ---
15B 1 Epoxy ---
15C 1 Ring ---
15D 1 Nylon/GF Housing ---
15E 1 Nut - Torque to 17.5 Ft-Lbs ---
15F 1 Kellum Grip Cable ---
15G 1 Cord ---
16 1 Plug ---
17 1 Upper Motor Housing ---
18 1 Capscrew ---
19 1 Lockwasher ---
20 1 Ground wire ---
21 4 Capscrew ---
22 4 Lockwasher ---
23 1 Bearing, 6202 - Upper PF17415
24 1 Spring Washer ---
25 1 Motor Housing ---
26 1 Mechanical Seal PF068988SK
27 4 Capscrew - Torque to 25 Ft-Lbs ---
28 4 Lockwasher ---
29 1 V-ring PF068053A
30 1 Spacer Seal PF63PFS4103
31 1 Impeller PF089369TG
32 1 Strainer 5000005
33 3 Leg ---
34 1 Mechanical Float, High Temp., 15 Ft. PF059-3640
35 1 Cable clamp ---
36 1 Capscrew ---
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
11
Risk of electric shock. Always disconnect the pump from the power source before handling inspections or repairs.
Symptom Possible Cause(s) Corrective Action
Pump will not run
Blown fuse or other interruption of
power; improper voltage.
Switch is unable to move to the “turn ON” position
due to interference with the side of basin or other
obstruction
Insucient liquid level
Defective level control
Check that the unit is securely plugged in. Have an
electrican check all wiring for proper connections
and adequate voltage and capacity.
Position the pump or switch so that it has adequate
clearance for free operation.
Make sure the liquid level is allowed to rise enough
to activate level control(s).
Remove and replace level controls
Pump will not turn o
Discharge is blocked or restricted
Check valve is stuck closed or installed backwards
Gate or ball valve is closed
Total lift is beyond pump’s capability
Pump impeller is jammed or volute casing is pluged
Check the discharge line for foreign material,
including ice if discharge line passes through or
into cold areas
Remove check valve(s) and examine for freedom of
operation and proper installation
Open gate or ball valve
Try to route piping to a lower level.
If not possible, a larger pump may be required.
Consult the factory
Disconnect unit electrically. Remove the pump
from the basin. Detach the pump base and clean
the area around the impeller. Rotate impeller by
hand. Reassemble and reinstall
Pump will not turn o
Level control(s) unable to move to the “turn OFF”
position due to interference with the side of basin
or other obstacle
Defective level control
Posistion the pump or level control so that it has
adequate clearance for free operation
Remove and replace level control
Pump runs periodically when xtures are not in use
Check valve is stuck open or is leaking
Fixtures are leaking
Remove check valve(s) and examine for freedom of
operation and proper installation
Repair xtures as required to eliminate leakage
Pump operates noisily
Debris in the impeller cavity
Damaged impeller
Worn bearings
Piping attachments to building are too rigid
Remove the pump from the basin.
Detach the pump base and clean the area around
the impeller. Reassemble and reinstall
Consult the factory for information regarding
replacement of impeller
Return pump to the factory or authorized repair
station for repair
Replace a portion of the discharge line with rubber
hose or connector
NOTE: Power-Flo Pumps & Systems assumes no responsibility for damage or injury due to disassembly in the eld. Disassembly of the pumps or supplied
accessories other than at Power-Flo Pumps & Systems or its authorized service centers, automatically voids warranty.
Trouble Shooting Chart
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps

Power-Flo Pumps & Systems • 877-24PUMPS • www.poweropumps.com
12
LIMITED WARRANTY
PFS411HTCE-2 Submersible Euent, Sump & Sewage Pumps
Manufacturer warrants, to the immediate purchaser and subsequent initial owner during the warranty period,
every new pump to be free from defects in material and workmanship under normal use and service, when properly
used and maintained, for a period of eighteen (18) months from date of manufacture or twelve (12) months from
date of installation (which ever comes rst). Failure due to wear due to excessive abrasives is not covered. The
initial owner is the purchaser who rst uses the pump after its initial installation, or for non-permanent installation,
the rst owner who uses the pump. The date of installation shall be determined by a dated sales receipt noting the
model and serial number of the pump. The dated sales receipt must accompany the returned pump. Product will be
repaired, replaced or remanufactured at Manufacturer’s option. No allowance will be made for shipping charges,
damages, labor or other charges that may occur due to product failure, repair or replacement. This warranty does
not apply to and there shall be no warranty for any material or product that has been disassembled without prior
approval of Manufacturer, subjected to misuse, misapplication, neglect, alteration, accident or act of God; that has
not been installed, operated or maintained in accordance with Manufacturer’s installation instructions; that has
been exposed to outside substances including but not limited to the following: sand, gravel, cement, mud, tar,
hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive substances, wash
towels or feminine sanitary products, etc. in all pumping applications. The warranty set out in the paragraph above
is in lieu of all other warranties expressed or implied; and we do not authorize any representative or other person
to assume for us any other liability in connection with our products. Contact Manufacturer at: 1-877-24PUMPS or
www.poweropumps.com, Attention: Customer Service Department, to obtain any needed repair or replacement
of part(s) or additional information pertaining to our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL
DAMAGES OR BREACH OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE
EXPRESSED WARRANTY.
Some states do not allow limitations on the duration of an implied warranty, so the above limitation may not apply
to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also have
other rights which vary from state to state.