PowerAcoustik AWB-10 User manual

POWERED SUBWOOFER SYSTEM

POWER ACUOUSTIK
* RCA INPUT/HIGH LEVEL INPUT
* P.W.M MOSFET POWER SUPPLY
* SOFT DELYED REMOTE TURN-ON
* DUAL COLOR INDICATOR L.E.D (POWER/GREEN & PROTECTION/RED)
* REMOTE CONTROL FOR SUBWOOFER LEVEL
* CONTROL: GAIN, PHASE, LPF, BASS BOOST
* PROTECTION CIRCUIT: THERMAL PROTECTION CIRCUIT
SHORT PROTECTION CIRCUIT
OVERLOAD PROTECTION CIRCUIT
* AUTO COOLING
YOUR NEW SUBWOOFER..........

Select a mounting location that allows easy access to the control while driving.
Using the subwoofer level control(remote) as a template, mark and drill holes
in the mounting surface.
UNDER DECK MOUNTING (Suggestion of the remote placement)
SUBWOOFER MOUNTING LOCATION
INSTALLING THE REMOTE
This

APOWER INPUT TERMINAL (CONNECTING THE POWER Fig. 1)
CONNECTION AND OPERATION
25A
A
G H I J
B
EFDC

25A
The amplifier is equipped with a plug-in auto fuse protecting set against
fault conditions. Do not use a fuse with a higher value and never bridge
the fuse over.
BFUSE
CONNECTING THE POWER (Fig.1)
Vehicle's chassis ground
To Power antenna
( )
POWER INPUT
CL.E.D
The L.E.D is a dual color indicator, when the +12v and REM +12 volt
power both switch on, The L.E.D illuminated green. this means that
the amplifier begin to work. if L.E.D illuminated red colour, this means
the amplifier is shut down from protecting circuit(thermal protection
& short protection & overload protection).

Use remote wire(accessory) connect "REMOTE SOCKET" to the
remote (accessory), the remote is for subwoofer level control.
Fig. 2 Connecting the subwoofer to remote
Rear view of remote controller
25A
DREMOTE (CONNECTING THE SUBWOOFER TO THE REMOTE Fig. 2)
ELINE IN(LOW LEVEL INPUT)
Use a pair of shielded stereo audio cable with RCA
type jack connect your receiver's "LOW LEVEL OUT"
to the RCA input
LINE IN
L
R

7
1. Remote..........1pc
2. Remote wire..........5m
3. High level input connector with wire..........1pc
4. Mounting magic tape.......2 sets
5. Mountint bracket & Screw..........1 set
6. manual..........1pc
ACESSORY LIST PER CARTON BOX
JGAIN
The "GAIN" control is subwoofer input level control, the input level control should
match the output of your radio. After the installion is complete, make sure the input level
control is turned down all the way(MIN). Play a tape or CD and turn volume up slowly until
you just start to hear distortion, now back the volume down just a bit. On the subwoofer,
slowly turn up the input level control(clockwise) until you start to hear distortion and back it
down a bit, Now your radio and subwoofer leves are matched.
IBASS BOOST
Varies from 0dB to 12dB of boost. Frequency adjustment control for
bass control filter.
HLPF
The low-pass crossover is continuously variable from 50Hz to 150Hz
GPHASE
The PHASE switch is used for changing woofer phase, set switch from
"0 " to "180 ", a phase shift of 180 degrees.
o o
1= White, Channel L-
2=Black, GND
3=White/Black, Channel L+
4=Grey, Channel R-
5=Grey/Black, Channel R+
FHI INPUT( HIGH LEVEL INPUT)
1 2 3
54
HI INPUT CONNECTOR WIRE(ACCESSORY)
White L- White/Black L+
Grey R-
1
4Grey/Black R+
5
3
Black, GND
2

8
SOUND
DISTORTED Input level control
adjusted too high Adjust input level control
Is volume minimum?
LOW
HIGH
ITEM
NET WEIGHT
LPF
INPUT SENSITIVITY
800W
<0.4%
>90%
20Hz TO 150Hz
50Hz -150Hz Adjustable
110mV
0.5V
25A
10 INCH
400 x 240 x310 mm
8.8kg
0dB-12dB
BASS BOOST
DIMENSIONS(L x W x H)
Note: SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.