PowerAcoustik SL-10W User manual

Amplifier
2-ohm Load
Amplifier
4-ohm4-ohm
1-ohm Load
4-ohm
4-ohm
4-ohm
4-ohm
-
++
-
-
+
-
-
++
-
+
Parallel voice coil configuration
Series voice coil configuration
Amplifier
4-ohm
4-ohm
4-ohm Load
4-ohm
4-ohm
Amplifier
8-ohm Load
4-ohm
4-ohm
Series/Parallel voice coil configuration
SL-10W
SL-12W
Owner's manual

Power Acoustik SL Series Woofers
Congratulations on your purchase of one of the finest woofers available
for your vehicle today.
If you are an enthusiast that plays your system loud and hard, the SL
woofers will take you to the limit. Our small sealed enclosure, high
excursion design will move enough air to part your hair. Let your
woofers do all the talking to let everyone know you are "Serious about
your sound".
Please take a few monents to fill out the warranty card and review this
manual before installing this woofer for proper connections and box
sizes.
Common Features:
Wide UV Coated Foam Surround
Black Chrome Coated PP Cone
Stiff Poly Cotton Spider
Dual 4 ohm 2" KSV Voice Coil
Reinforced Aluminum Voice Coil Former
Integrated Tinsel Leads
Stamped Steel Basket
Steel Gasket
Black Chrome Finish
Chrome Push Terminals
Vented Pole Piece
Model Sealed Box Size Ported Box Size Port (dia x length)Tune Freq. #of Ports
SL-10W
Sl-12W
.95 cu. ft.
1.25 cu. ft.
1.25 cu. ft.
2 cu. ft.
38 Hz
38 Hz
1
1
3" x 8"
4" x 8.25"
Building the Enclosure
The following page will give you a few different options to match the
impedance of the woofers to the impedance capability of the amplifier.
Please read and follow the diagrams closely to insure maximum
woofer performance.
Determine the dimensions of your enclosure.
Be certain the box dimensions that you have designed will fit in the
location you have chosen in your vehicle. Sometimes making a
outside dimensions is helpful.
It is recommended to use .75*inch thick MDF (medium density
fiberboard) to build you speaker box.
Use a "T" square to verify precise right angle cuts before you assemble
the box. Use high quality wood glue and screws to assemble the box to
apart due to excess vibrati
on and pressure. It is recommended for sealed enclosures to stuff the
interior of the box with approximately 50% Dacron or Polyester
fiberfill for increased sound damping and woofer performance.
For ported enclosures, it is recommended to staple 1" thick Dacron or
Polyestrer insulation to the interior walls of your box.
Use slide on connectors for spade style connectors or bare wire for push
and screw terminals. Do not solder the wires to the factory connectors
as this may cause damage to the voice coil or tinsel lead and may void
your warranty.
cardboard box with the same
guarantee an airtight box that will not come
Recommended wiring
Recommended Box Sizes
Specifications:
SL-10W
800 watts power handling
400 watts RMS
70 oz. magnet
2" KSV voice coil
SPL 89 dB
Fs:42 Hz
Vas:1.06 cu.ft.
Qms: 4.057 Qes: .667 Qts:.573
Xmax:.32"
SL-12W
1000 watts power handling
500 watts RMS
80 oz. magnet
2" KSV voice coil
SPL 89 dB
Fs:39 Hz
Vas:1.20 cu.ft.
Qms: 2.019 Qes: .674 Qts:.506
Xmax:.32"