PowerBridge ONE-PRO-6 User manual

Power + Cable Kit - Model #ONE-PRO
Power Extension Cable Management
Tools for Installation
Not Included
Stud Finder Flat-Blade
Drywall Saw
Caution - Risk of Fire - Do Not Install Power Supply Cord Within the Wall Cavity
WARNING - Risk of Fire and Shock, Do Not Connect this Box to any Other Circuits or Outlets.
This kit is rated to 15AMP 125Volt AC only
Do not install this product near water, example, near a sink, tub, shower, swimming pool or laundry area.
Manufacturer is not liable for damages due to improper installation methods not followed herein.
This product does not have built-in electronic circuitry for surge protection or A/C filtering.
It is recommended that this product be connected to a quality surge-protector/power conditioner for equipment protection.
Disclaimer. HD-Products, LLC, the Manufacturer, it's agents, suppliers, and affiliates, shall not be liable for any damages, not limited to; misuse, acts of nature,
verbal and written expression and improper installation. Improper installation is determined such to include, not limited to, non-code compliant installation, product
modifications, alterations, adjustments, and substitutions of components or materials.
Limited 2-year Warranty from Manufactures Defects: Limited Two Year product warranty against manufacturer's defects.
Step 1 Location - Wall Cutout
Use supplied template sheet to mark area to cut out from drywall.
Use a level to maintain proper alignment.
Carefully use drywall saw or utility knife to cut along outside of line.
Vertical
or Horizontal
Do not exceed more
than 60” apart from
existing outlet or
surge-protection unit
PowerOUT
PowerIN
HD-Products, LLC intent to make this manual accurate and complete. However, HD -Products, LLC makes no claim that the information contained herein covers all details, conditions, or
variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change
without notice or obligation of any kind. HD-Products, LLC makes no representation of warranty, expressed or implied, regarding the information contained herein.
HD-Products, LLC - PowerBridge Solution 7399 S. Tucson Way C-2, CO 80112 USA
Customer Service: 855-755-9838 [e-mail] www.PowerBridgeSolution.com
Part No. ONEPRO-417v3.1 2016 All Rights Reserved
PowerBridge can only be installed
within standard construction walls.
Only attempt installation within
2x4 or 2x6 wood/metal stud
framed wall.
!
!
PowerOUT PowerIN
Level
If insulation exists,
remove or push
completely away
from the openings
to allow proper
flush mounting.
!
Wall Cut-out Template:
Lay against wall, use a level on edge
of paper to align.
Use a pencil to trace around edge.
Use drywall saw or sharp utility
knife cut on the edge of the line.
Remove drywall section.
2.1/4” x 3.5/8”
57mm x 93mm
Model #ONE/Pro
LEVEL
CODE COMPLIANCY
SUPPORT
1)NEC Article 334.30
Unsupported NM Cable
2) NEC 2014 Article 400.7(A)(11)
Permitted use of cord / approved kit
using inlet to energize receptacle
Meets all US states and cities
adaptive to the National
Electrical Code (NEC)
allowing NM type building cable.
Specific locations not allowing
NM-type building cable:
~Cook County, IL ~NYC, NY
Kit Includes: ONE-PRO-6 also includes pre-stripped 6’ in-wall PowerWire
PowerOutlet | PowerInlet | 72” PowerConnect Supply Cord | Template
Hex Tool
PowerOUT - Determine TV wall mount bracket location.
Align between wall framing studs.
Use stud finder to determine in-wall obstructions
between framing both VERTICALLY and HORIZONTALLY.
Install in any direction, right/left, below, above,
next to TV wall bracket.
PowerIN - Align with upper PowerOUT within same stud-bay
no more than 60” apart.
Install within 60” from an existing power outlet or power-surge device.

Step 2 In-Wall Installation
A) Begin at the upper PowerOUT location.
Drop or wall-fish audio video cables and NM-type
PowerWire to the PowerIN location below.
Pull all cables out lower cutout.
Step 3 Plug it in
Plug TV power supply cord in to PowerOUT and connect AV cables to TV.
Follow wall mount manufacture instructions, install TV on wall bracket.
Plug supplied 6’ PowerConnect cord into PowerIN.
Plug other end into existing grounded outlet or surge protector.
CAUTION-Risk of Fire-Only Use Cord Set Provided With This Kit or equivalent.
Plug in TV Plug in Flat Angle Plug
I) Slide audio video cables through backside through CableBrush.
Allow for enough cable length out to connect to TV and Equipment.
J) Slide both wall plates into wall opening.
Use Flat-Blade screw driver to secure panel to wall.
Careful to not over-tighten!
The PowerBridge In-Wall Extension is now energized.
Existing
Outlet
Surge Protector
B) SKIP THIS STEP with supplied pre-stripped PowerWire
If you use your own wire, follow Wire Strip Gauge on label.
C) Wire PREP - Follow steps as shown for BOTH ends
D) Insert PREPPED PowerWire as shown through funnel into
back-boxes for OUTLET/INLET.
E) Tighten all three screws securing wires.
F) Bend all three wires toward the cable-brush.
G) Slide back-box onto back, pull PowerWire back up through
as shown, secure with the 4 supplied black screws with
supplied hex-tool.
H) Align wire in-between guides. Insert-snap supplied clamp
part into slots, snap both sides in place.
E
F
Wire Connection - Assembly
< Silver
WHITE Wire
Screw
TOP
Brass Screw >
BLACK Wire
Green Screw BARE Wire
W
Silver
WHITE Wire
Screw >
TOP
< Brass Screw
BLACK Wire
Green Screw BARE Wire
W
G
OUTLET
INLET
Use NM-type building wire.
14/2 size wire only.
Copper wire only CU
!
B
1.5”
1/2”
Wire Strip Gauge
NOTE:
Kits supplied with
PowerWire are
already pre-stripped,
SKIP this step
J
I
6”
Half way-
slightly
bend wires
as shown
Bend in
hook shape
Wire PREP
DO THIS FIRST BEFORE WIRE CONNECTIONS
!
C
D
H
G