PR RACING VB-10 User manual

www.pr-rc.com
ITEM NO:69000020
PR SC201 MM (VB-10) Off Road 1/10 2WD Short Course Truck Kit

Specifications
Items required
PR SC201 MM (VB-10) Off Road 1/10 2WD Short Course Truck Kit
Motor: Electric
Chassis Kick-up: 25-degrees
Hardware: Full metric
Bearings: Shields Metal Ball Bearings
Wheels : Wheels with 12mm hex (front and rear)
Spur Gear: 73-75-77-(81)-83-tooth 48-Pitch
Drivetrain:2WD(MM)
Motor: Electric 540-sized
Kit/RTR: Kit
Shock Type: Oil-Filled Aluminum Shocks
Body: (Clear)
Driveshafts: Full set of 2 CVA
1/10 SC Tires, inserts
Width: 296 mm
Weight: 1000-1100g (weight varies with choice of electronics, tires & body)
Wheelbase: 325mm-329mm
Gear Ratio: 2.6:1
Battery choice: 7.4V/4000-6000mAh approx,
Minimum Age Recommendation: 14 years old
Metric 1.5mm, 2.0mm hex tools
Metric 5.5mm, 7.0mm Nut Driver
2 Channel Surface Radio System (Minimum)
1/10 ESC, Motor & Pinion Gear
High-Speed Servo
2S LiPo Battery & Compatible Lipo Charger
Polycarbonate Paint for Bodies
Tires CA Glue
Silicon diff oil
LOK threadlocker

Needle Nose Pliers Awl Grease
Screw Cement Round Cutter & Sander
Sharp Hobby Knife
Hex Wrench
1.5mm
2.0mm
Ball Differential Grease
Ware Cutters
SP Knife Edge Reamer Cross Wrench
For trimming bodies Cutting
along curved lines was never
so easy!
Do not pre-drill as precise
drilling of 1mm to 15mm
holes can be performed after
body shell painted.
A new battery must be charged before it is used. Refer to the charger instruction manual for charging.
Set up the radio control system as indicated below.
Battery
Transmitter
Off
On
Charger
Eletronic Speed
Controller
Receiver
Servo
Install batteries.(Transmitter)
Extend the antenna.(Transmitter)
Connect the battery to the ESC.
Extend the antenna.(Receiver)
Switch on both the transmitter and receiver.
Make sure the servos are in command.
Switch off both the transmitter
and receiver.
Retract the antrnna.
(Transmitter)
Center the trims.
Off
On
Off
On
TOOLS REQUIRED
RADIO PREPARATION

06
Front Spindle-Right Side
07
Front Suspension[Left Side]
Front Upper Turnbuckle Assembly
Front Shock Stay
Front Bumper Set
Turnbuckle Assembly-Steering Rod
Rear Chassis Brace (Mid Motor)
Rear Hub & CVD
Rea Suspension Mount
Motor Mounts [Mid Motor]
Rear Body Mount Set
15
16
Front & Rear Shock Assembly
Motor Guard set
Rear Bumper Set
20
Battery Plate
Tires
21-22
Battery Column
Differential Gear
10
03
1210
13

Part Bags used. Assemble left and right
sides the same way.
BAG
A
Chassis Guard Installation
A1
Servo saver
A2
Tighten securely.
BAG
A
69400086
03
2
M4.8X6mm Ball Studs
68430036
1
M3X10mm Button Head Cap Screw
80400046
M4.8X6mm Ball Studs
M3x10mm
2019-68480036 2019-68480036
66000020-2
M3x8mm Flat Head HexScrew
82400026
12
M3X8mm
M3X8mm
M3X8mm
M3X8mm
M3X8mm
M3X10mm
M3x10mm Flat Head HexScrew
82400106
4
69400066(L/R)
M3X10mm
66401306
鎖緊退回半圈

Servo saver
A3
Steering Servo
A4
BAG
A
BAG
A
04
M3X10mm
66402466
66400066
M3X10mm
M4.8X6mm
M3
83480016
29.3mm
M3x10mm Set Screw-87400026
1
M4.8mmx6mm Ball Studs-68430036
1
M3x10mm Flat Head Hex Screw-82400106
1
83480016 M3 Nut
1
Apply threadlocker (screw cement)
2
66402106
4
M4.8X6mm
(-0.8mm) 5x8x2.5mm
Plastic Bearing
5x8x2.5mm
Plastic Bearing
-5x8x2.5mm Plastic Bearing
68430086- M4.8X6mm(-0.8mm)
3:1
分辨缺角
Distinguish

Steering Servo
A5
Steering Servo
A6
BAG
A
BAG
A
M3x8mm
82400026
M3X8mm Flat Head Hex Screw
2
05
80400036
3X8X0.5mm
85000010
M3X8mm Button Head Hex Screw
4
3X8X0.5mm Shim
4
3X8X0.5mm
66400116
4
80400046
M3X10mm Button Head Hex Screw
According to different brands servo,
you can decide to use 1mm or
1.5mm (thickness).
66430200
66430200
M3X8mm
80400036
or
M3X10mm
80400046
66430200
1.0mm
1.5mm

M3x8mm
80400036
3x36.8mm
66430110
(R)
(L) 67400036
67400106
3X8mm Button Head Hex Screw
3x36.8mm Pin
2
2
66000020-1
66400036
Front Suspension
B1
Front Spindle[Left Side]
B2
+5mm
+KicKup 25
67400036
M2.5x4x5.5mm
2
2
1
1
3
3
2.5x4x5.5mm Button Head Hex Screw
80400016
2
M2.5X4mm
M4.8mmx6mm Ball Studs-68430036
BAG
B
BAG
B
M4.8x10mm Ball Studs
1
M4.8X6mm
66400046
(For SC201)
67400216 M4.8X10mm
- 68430076
66400046
2X10.8mm
79400016
1
2
3
5X10X4mm
4
Vertical lock
4
66401686
Vertical lock
66401686
-66401686
Steering Screw Stepped
2
68410066
4mm-Plastic
1
2
89430010
5x10x4mm ZZ Ball Bearing
12X8mm-Plastic
67400166-2
06

Front Spindle[Right Side]
B3
Front Suspension[Left Side]
B4
3X27.80mm
M2.5x4x5.5mm
80400016
Please modify elasticity
by this screw.
For swing arm smooth
Please modify elasticity
by this screw.
For swing arm smooth
80400016
M2.5x4x5.5mm
2
2
79400106
3x27.8mm Pin
BAG
B
07
y
M2.5x4x5.5mm
66400046
M4.8X6mm
66401036
(For SC201)
67400046
66400046
66400766
2X10.8mm
79400016
1
4
2
3
5X10X4mm
Steering Screw Stepped
66401686
66401686
4
M4.8X10mm
68410066
4mm-Plastic
M4.8mmx6mm Ball Studs-68430036
M4.8x10mm Ball Studs
1
- 68430076
-66401686Steering Screw Stepped
2
1
2
89430010
5x10x4mm ZZ Ball Bearing
BAG
B
12X8mm-Plastic
67400166-2

Front Shock Stay
B5
Part Bags used. Note the direction. True-to-scale diagram.
Front Shock Stay
B5
BAG
B
BAG
BB6 Front Upper Turnbuckle Assembly
66400066
50mm
50mm Turnbuckle Rods
67410026
2
4
Shock Ball End&Spring Cupset&Rod End
29.5
mm
66400066
One side is reverse threaded.
31.3mm
Assemble in the
specified order.
M4.8x6mm Ball Studs
2
M3x10mm Flat Head Screw
2
M3X12mm Button Head Hex Screw
6
M3X18mm Button Head Hex Screw
2
M3X12mm
82400036
M3X10mm
82400106
1
M3X12mm
2
M4.8X6mm
69000040
69400046 M3
83480026
M3X18mm
80400196
M3X12mm
80400206
25
67400106
3
組裝前車殼柱時,
請注意斜面貼近前避震板
M3x12mm Flat Head Screw
2
68430036
Hole 1
4
M3 Lock Nut
83480026
2
69400016(2021)
When install front body mount,
please notice inclined
plane close to
front shock tower.
08

Part Bags used.
BAG
B
09
Front Bumper Set
B7
M3X14mm Flat Head Hex Screw
4
M3X14mm
-82400046
69400026
69400046
M3X18mm
-82400126
M3X10mm
-82400106M3X10mm Flat Head Hex Screw
2
M3X18mm Flat Head Hex Screw
2
1
Assemble in the
specified order.

Part Bags used.
Assemble left and right
sides the same way. Note the direction.
One side is reverse threaded.
BAG
B
BAG
C
Turnbuckle Assembly-Steering Rod
B8
Rear Chassis Brace (Mid Motor)
C1
L
R
L
R
2
Rod End-R-66400066
1
1
2
50mm Turnbuckle Rods-67410026
Rod End-L-66400066
Rod End 31.3mm-664000660
M3X18mmFlat Head Hea Screw
2
M3X25mm Button Head Hex Screw
4
M3X18mm
82400126
M3X25mm
80400076
69400016
66400056
10
31.3mm
34.2
mm
34.2
mm

Part Bags used. Assemble left and right
sides the same way.
Battery Column
C2
Assemble as many times as
specified (here:twice).
BAG
C
BAG
C
Rear Hub & CVD
C3
66410036(82.50mm)
66401096
2x9.8mm
66410016
2x10.8mm
5X13X4mm
89430020
10X15X4mm
89430030
66400046
10X15mm Ball Bearing
2
5X13mm Ball Bearing
2
12X8mm-Plastic
67400166-2
M3X20mm Set Screw
2
M3X20mm
87400086
請以照電池位置不同,將M3X20mm止付螺絲前後調整
Please according to the battery difference, adjust the
M3XM20mm set screw front and rear.
11

Part Bags used.
Rear Hub
C4
BAG
C
BAG
C
M2.5x4x5.5mm Button Head Hex Screw
80400016
3x36.8mm pin-66430110
2
2
67400036
3x36.80mm
M2.5x4x5.5mm
1.85mm
Fornt
上孔
TOP hole
車頭
2
1
M3X8mm Flat Head Hex Screw
4
3X8X0.15mm Washer
2
82400026
M3X8mm
85440320
2
3X47.5mm-66430120
66000020-3
66000020-4
66400566 3X8X0.15mm
85440320
68410066
Please add it or not
according to the loose-tight.
依據鬆緊，請加它或不加它。
3x47.5mm
M3X8mm
Rea Suspension Mount
C5
Assemble left and right
sides the same way.
L
12

(A)
Gear Dierential
D1
Apply oil.
BAG
D
KIT-66480976 steel
OP-66480356 aiuminum
66480296
4X10X0.15
Shim x1pcs
66481366
+1.6mm
66481366
+1.6mm
66480296
5X1.5mm(o-ring)
31450016
5X8X0.8mm
85440170
85400016
66480336
66480336
85400016
5X8X0.8mm
5X1.5mm(o-ring)
31450016
M2.5X8mm
80000021
66480366
建議濃度為1000-3000差速油
灌至八分滿
66430260
The recommendable
density is 1000-3000
differential oil,
please pour in the
differential oil
reached up to 80%.
85440170
5X8x0.8mm Shim
2
2
85440160
4X10x0.15mm Shim
2
85400016
3.5mmE buckle
74480036
Gray
66481366
+1.6mm
80000021
M2.5X18mm Flat Head Screw
4
MAX
27.8mm
13
4X10X0.15
Shim x1pcs
4

Motor Mounts [Mid Motor]
D2
Part Bags used.
BAG
F
89430010
89430030
5X10X4mm Ball Bearing
7
2
10X15X4mm Ball Bearing
Option Parts
28t(Aluminum)
66480010
如果馬達使用10.5t以下規格
建議使用此改裝零件
If you use the motor which below
10.5 t, we recommend you to use
this modified parts.
66400926
MM
M3x32mm
M3x14mm
M3x36mm
M3x20mm
66400516
3x14mm Button Head Hex Screw
80400056
3x20mm Button Head Hex Screw
804000066
3x32mm Button Head Hex Screw
80400086
3x36mm Button Head Hex Screw
80400096
1
1
2
1
M4.8x6mm Ball Studs
2
68430036
M4.8X6mm
M4.8X6mm
14
66400526
79400056
5X10X4mm
7pcs
28t
66400096
k it-71400116(81t)
op-66480606(83t)
66400466
66480306
66480826
M4
Slipper Spring
1
M4 Lock Nut
1
66480826
83400036
此處螺絲鎖入勿緊迫

Rear Body Mount Set
D3
BAG
F
M3X14mm Button Head Hex Screw
2
M3X15mm Flat Head Hex Screw
2
80400056
82400176
2
2
M3x15 mm Flat Head Screws
82400176
66401806-Ball Joint
77430066-55mm Turnbuckles
One side is reverse
threaded.
M3X15mm
66401806
One side is reverse threaded.
38.5 mm
66400066
67410036
55mm
2
2
M3x10 mm Flat Head Screws
82400106
Assemble in the
specified order.
4
48mm
Part Bags used.
69400016(2021)
66400106
M3X14mm
組裝車殼柱時
請注意將平面貼近避震板
When install front body
mount,please notice plane
close to front shock tower.
Front
15
M3X15mm
M3X10mm
1MM

02530086
02530036
E1 Front & Rear Shock Assembly
4
OP
80000020
M2.5X4mm
(4.5mm)
66430040
66430050
66400186
Black
Rear Build x2
Front Build x2
19.40 mm
Slowly move up
and
down to remove
air bubbles.
o
oo
oo o
oooo
o
o
o
oo
o
oo
o
oo
o
oo
Front Build x2 Rear Build x2
Join the
spring cup
Slowly push the shock shaft all the way
up,wipe away any excess oil that has
seeped out, and screw in the bleeder
screw.
k g /m m lb s/in
Bl ue Red
Wh i t e
Ye llo w
Bl ue Red
Wh i t e
Ye llo w
Wh i t e
B la c k
Tr ansp ar ent
Tr ansp ar ent
Bl ue
Wh i t e
Re d
Ye llo w
Gr een
Bl ue
Re d
Ye llo w
Gr een
B la c k
Black
Green
02530116 0.098-(RT) 5.88-(RT)
Black
Green
02530126 4.50-(RT)
02530046
02530036
02530026
02530016
02500126
02500116
02500146
02500106
02500096
0.090
0.085
0.080
0.075
0.068
0.063
0.061
0.058
0.053
0.030
0.035
0.037
0.040
0.045
0.050
0.055
0.060
0.065
0.073-(RT)
3.90
3.30
3.60
3.00
2.70
2.40
2.22
2.10
1.80
5.04
4.76
4.48
4.20
3.81
3.53
3.42
3.25
2.97
02500056
02500066
02500136
02500076
02500086
02530056
02530066
02530076
02530086
2019 PR 1/10 Type R Shock Spring
71530016-Type R Front Shock Spring Set (Not included-02530016)
PART NO: Color
71530026-Type R Rear Shock Spring Set (Not included-02530126)
E1.1
E1.2
INCORRECT CORRECT
Front -27mm
Rear -33.5mm
450-500 cst
8mm 11mm
19.40 mm
66400186
Black
BAG
E
BAG
E
BAG
E
66430050
A Bag
Apply threadlocker (screw cement) Apply oil.
Part Bags used.
After first drive
adjust
for track conditions
Front 17430156
Front 77410016 (44mm)
68410066
1.6mmx2 hole
Assemble 2 front
and
2 rear shocks
Rear 17430166
Rear 77410026 (51mm)
KIT-68410066
OP-55430076 -Black
OP-66401826 (Steel)
66400186
(18.5mm)
83400066
m2.5
85440070
Shim
2.6 x6 x0.5mm
31430016 O-ring (Red)
31280146
(14X1.2mm) O-Rings
2:1
2:1
Aluminium Shock Kit Tighten M2.5 Nut without the
use of plier, do not over tighten.
Recommend to use the thread
lock instead.
66430070
KIT-68410066
OP-55430076 -White
Shim
0.36mm
Do not push the shock rod straight
through the lower shock body
assembly; O-ring damage may result..
EXTREMELY
IMPORTANT
x
1.6mmx2
hole
68410066
Length
Assemble in the
specified order.
66430200
1mm
Twist the shock rod through
the lower shock body
assembly.
Front
Rear
Front (21.5mm)
KIT-66402106-2 (POM)
16
31430016 O-ring (Red)
Shim 0.36mm
Apply oil. Apply oil.

Part Bags used.
Front Shock Assembly
E2
Rear Shock Assembly
E3
BAG
E
BAG
E
M3X28mm Button Head Hex Screw
4
M3X28mm
68410066
68410066
67400036
Plastic
69440010
66400246
M3X28mm
80400126
83480016
M3 Nut
2
One side is reverse
threaded.
Note the direction. 17
Apply threadlocker (screw cement)
Apply threadlocker (screw cement)
80400056
M3X14mm Button Head Hex Screw
2
83480016
M3 Nut
2
80400126
M3X28mm Button Head Hex Screw
2
One side is reverse
threaded.
66430200
1mm
Apply threadlocker (screw cement)
(A BAG)
M3X14mm
68410066
83480016
M3X28mm
69440010
螺絲鎖入勿緊迫

Motor Guard set
E4
Rear Bumper Set
E5
BAG
F
BAG
F
M3X25mm Button Head Hex Screw
1
80400076
69400076
MM
M3
83400026
69400036
M3X18mm
82400126
M3X18mm Button Head Hex Screw
2
M3 Lock Nut-83480026
3
M3 Lock Nut
M3X25mm
69400076
M3X12mm
69400076
SC201
M3X30mm
82400136
or
VB-10
M3X14mm
69400036
M3X14mm Flat Head Hex Screw
4
M3X30mm Flat Head Hex Screw
4
82400046
82400156
M3X22mm Flat Head Hex Screw
4
M3X22mm
M3X12mm Button Head Hex Screw
2
80400206
VB-10
SC201
O
X
Part Bags used.
18 Assemble in the
specified order.
4