Premier Mounts CONVERGENT SAM-IFJ Series User manual

www.premiermounts.com | North America 800.368.9700 | International [phone]
2620 Palisades Drive, Corona, CA 92882 USA
950 025 4 v1.1
publ. 01/24/19
SERIES: SAM-IFJ
INSTALLATION GUIDE
Convergent Series Video Wall Mount
For Samsung IFJ LED Cabinets

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
Page 2
METHOD 1 METHOD 2
Assemble the mount before installing into
place (for single unit or small array).
Install piece by piece on a located wall (for
multiple or large video wall array).
CAUTION STATEMENTS
1. READ ALL STEPS WITHIN THIS MANUAL BEFORE INSTALLING THE MOUNT. SAMSUNG IFJ LED
SERIES INSTALLATION GUIDE MUST BE READ IN CONJUNCTION FOR SUCCESSFUL
INSTALLATION. ANY QUESTIONS? CALL PREMIER MOUNTS.
2. INSTALLATION MUST MEETS THE REQUIREMENTS APPROVED BY THE STRUCTURAL ENGINEER.
3. FRAME MUST BE PLUMBED, SQUARED, LEVELED, X, Y, AND Z ALIGNED PRIOR TO INSTALLATION OF
ANY DISPLAYS.
4. ALL LED CABINETS MUST BE POWER ON TESTED PRIOR TO ANY INSTALLATION.
5. PREMIER MOUNTS RECOMMENDS THE HANDLING LED CABINETS BY AN INDUSTRY QUALIFIED
PROFESSIONAL.
6. PREMIER MOUNTS IS NOT RESPONSIBLE FOR DEFECTS, MISUSE, OR IMPROPER HANDLING OF THE
LED CABINETS.
Tools for Installation:
00.0 o
Spool of
colored strings
Anti-Static
Gloves
LASER

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone] Page 3
Available
Sizes
Imperial
(Inches)
Metric
(Milimeters)
X
1 Wide 31.718 805.6
2 Wide 63.466 1612.1
3 Wide 95.214 2418.5
Y
1 High 17. 828 452.8
2 High 35.686 906.4
3 High 53.545 1360.1
4 High 71.403 1813.6
5 High 89.261 2 2 67. 2
VIDEO WALL DIMENSIONS AND MOUNTING LOCATIONS
The overall dimensions of any video wall array can be
calculated by using the table within this page.
The desired array size is a combination of available sizes.
Add the available sizes together to nd the overall width or
height of a given array.
For modular conguration, any combination of the rails
does not affect the overall dimension of the mount.
For example: 3X3 array would be 95.22” x 53.54” but larger
array i.e., 9X9 would consist of multiple rails for an overall
of 285.65” x 160.66”.
X
Y
AFF
LASER
LEVEL

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
Page 4
10 4000-300-531-LX Vertical Left End Rail 3V
11 4000-300-532-LX Vertical Center Rail 3V
12 4000-300-533-LX Vertical Right End Rail 3V
13 4000-300-541-LX Vertical Left End Rail 4V
14 4000-300-542-LX Vertical Center Rail 4V
15 4000-300-543-LX Vertical Right End Rail 4V
16 4000-300-551-LX Vertical Left End Rail 5V
17 4000-300-552-LX Vertical Center Rail 5V
18 4000-300-553-LX Vertical Right End Rail 5V
ITEM #. PART NO. DESCRIPTION
1 4000-300-501-LX Horizontal Rail 1H
2 4000-300-502-LX Horizontal Rail 2H
3 4000-300-503-LX Horizontal Rail 3H
4 4000-300-511-LX Vertical Left End Rail 1V
5 4000-300-512-LX Vertical Center Rail 1V
6 4000-300-513-LX Vertical Right End Rail 1V
7 4000-300-521-LX Vertical Left End Rail 2V
8 4000-300-522-LX Vertical Center Rail 2V
9 4000-300-523-LX Vertical Right End Rail 2V
2 WIDE
1 HIGH 2 HIGH 3 HIGH 4 HIGH 5 HIGH
3 WIDE
1 WIDE
1
9
12
15
181716
6
7
10
13
5
8
11
14
2
3
4
AVAILABLE
SIZES

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone] Page 5
PRE-INSTALLATION
Even array - e.g. 6 Wide
Odd array - e.g. 3 Wide
Identifier for the
top or bottom
horizontal rail
UNUSED
FLOATER
LOCATION
every other and
corner location
every other and
corner location
Nylon Washer
Steel Washer
M5 x 10mm
Comb Screw
M6 x 35mm
Socket Screw
Default Position and aligment
indicator for wall leveling bracket
Floating Adjustment Assembly
(or “Floaters”)
1/2”-13 x 1.5”
Bolt With Hole
To keep the
flange straight
AT ALL TIMES.
DO NOT
REMOVE.
Wall Leveling
Bracket
Floaters must be install on every edge and middle location (if applicable) of each Horizontal Rail.
When installing an adjacent horizontals, only one floater is used at the seam.
1. Examine the rectangular cutout with V-groove of each Horizontal
Rail to determine the placement of the Floating Adjustment
assembly (or “oaters”) shown on above.
2. Install the oaters by following the directions above.
3. Fasten using (2) M5 x 10mm Comb Screw, (2) Nylon Washers,
(2) Steel Washers.
4. Install 1/2”-13 x 1.5” Bolt with Hole onto each threaded extrusion
and a M6 x 35mm Socket Screw for ease of installation in
sequential step.
Edge
location
Edge
location
Middle location
(Vice-Versa)
3 Wide horizontal rail shown for clarity.

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
1
2
Page 6
Horizontal
Rail
M5 x 8mm
Flat Head
Install the Vertical and Horizontal Rails together using (4) M5x 8mm Flat Head Screw per.
1. Determine the desired location by calculating the height of the pre-mounting hang location using
the table on page 3.
2. Use any commercially available hardware to temporary hang the mount.
METHOD 1
Support
Screws
To temporar y
hang the mount
48” apart
Vertical Rail
(center)
Vertical Rail
(left and right)

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone]
3
Page 7
1. Place a level on top of the mount and reinstall or adjust the support screws if necessary.
2. Secure the rst mounting location by sliding a Wall Anchor Plate behind the mount and fasten
using 1/4” x 5” Hex Lag and 1/4” Washer.
3. Maintain a 1/8” minimum gap from the anchor plate and the rail when anchoring.
4. Install the remaining mounting locations while keeping the mount leveled.
LASER / LEVEL
00.0 o
1/8” min. gap
Clearance
1/4” Washer
1/2”-13 x 1.5”
Bolt With Hole
Wall Anchor
Plate
Vertical Rail
1/4” x 5” Hex
Lag
Support Screw

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
1
Page 8
00.0 o
LASER / LEVEL
WALL WALL
1. Install (2) 1/2”-13 x 1.5” Bolt with Hole onto the threaded extrusion.
2. Hang the rst Horizontal Rail on the wall.
3. Secure the rst mounting location by sliding a Wall Anchor Plate behind the mount and fasten
using 1/4” x 5” Hex Lag and 1/4” Washer.
4. Maintain a 1/8” minimum gap from the anchor plate and the rail when anchoring.
5. Level, Square, Plumb.
6. Install the remaining lag bolts, washers, and wall anchor plate.
METHOD 2
1/8” min. gap
Clearance
1/4” Washer
1/2”-13 x 1.5”
Bolt With Hole
Wall Anchor
Plate
Vertical Rail
1/4” x 5” Hex
Lag
Wall Anchor Plate Wall Anchor Plate

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone]
2
3
Page 9
Vertical
Rail (Left)
Horizontal Rail
(Mounted)
1. Securely fasten each Vertical Rail to a mounted Horizontal Rail using (2) M5 x 8mm Flat
Head Screw per end.
2. Fasten the Lower Horizontal Rail but do not anchor until the mount is perfectly square. See
sequential step.
ASSEMBLE THE LOWER SECTION OF THE MOUNT
Install a few support screws (commercially available hardware) to temporary hold the lower
section in place prior to final mounting location.
Vertical Rail
(Right)*
M5 x 8mm
Flat Head
Lower
Horizontal Rail
*Single unit configuration shown above. Left and right rails are for the entire array.
Vertical Rail
(Center)
Installation is not finished within this step. After leveling the vertical brackets,
secure the bottom horizontal to the wall. See step 8 for additional detail.
Support
Screws
Do Not Anchor Prior to
Final Mounting Location

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
4
Page 10
Multiple Unit Conguration
1. Hang and position the second Horizontal Rail side by side.
2. Place a support screw while maintaining a leveled horizontal rail to temporary hold in place.
3. Install (2) Attachment Plate and fasten together using (4) M5 x 8mm Flat Head Screw for each rail.
4. Install the remaining Vertical Rails (center) using (4) M5 X 8mm Flat Head Screw.
5. Install the lower section of the mount as the steps above.
To extend the width of the unit, follow the steps below.
Extend Horizontally
Horizontal Rail
(1st unit)
Horizontal Rail
(2nd unit)
LASER / LEVEL
the seems between
two units 00.0 o
Attachment
Plate
M5 x 8mm Flat
Head Screw
Vertical Rail
(center)
Figure 1
Figure 2
Insert a support
screw temporary
hang the mount

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone]
5
Page 11
Extend Vertically
Multiple Unit Conguration
1. Position multiple units adjust to each other.
2. Joint the units together using multiple Attachment Plate and fasten using
(2) M5 x 8mm Flat Head Screw per.
3. When extending the height of a video wall array, the middle row shares the
Horizontal Rail between two units. Additional Horizontal is not required.
To extend the height of the unit, follow the steps below.
No additional
Horizontal Rail
No additional
Horizontal Rail
Required.

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
6
Page 12
Inspect each bracket using a Square and Level tool.
LASER / LEVEL
SQUARE AND LEVEL
00.0 o

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone]
7
Page 13
0.281” Dia hole
M5 x 0.5mm
tapped hole
(with supplied
M5 x 20mm)
1. Install whereever necessary.
2. Use multiple drywall or wood screws to bring the bracket closer to the wall.
3. Use multiple M5 x 0.5 tapped screws to bring the brackets away from the wall.
FINETUNE THE HORIZONTAL AND VERTICAL RAIL
Towards the wall
Against the wall

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
8
Page 14
REMINDER
1. Measure the distance from corner to corner
with a measuring tape.
2. Measure diagonally opposite and verify the
diagonal measurements.
3. Proceed only if the two measurements are
equivalent.
4. Secure the lower mounting location by sliding
a Wall Anchor Plate behind the mount
and fasten using 1/4” x 5” Hex Lag and 1/4”
Washer.
INSTALL THE LOWER
MOUNTING LOCATIONS
Distance 1
Distance 2
The two diagonal
measured distances
must match
1/8” min. gap
Clearance
VERY IMPORTANT!
VERIFYING THE DIAGONAL MEASUREMENTS FOR SQUARENESS

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone]
9
Page 15
1. Tie a string from one end to the other end of the entire array.
2. Tie horizontally and crisscross, especially for large video wall array.
3. Inspect for any gaps between the brackets and the string.
4. Adjust any neccessary mounting location.
FINAL ALIGMENT AND ADJUSTMENT
STRING
Figure 2
Convergent Brackets
Bright Colored String
(Z-Axis indicator)
Figure 1
SOLID OR PLYWOOD BACKING WALL
Visual inspection for Z-adjustment

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
10
Page 16
Uneven wall surfaces can be
adjust by turning the Flush Bolt.
In / Out
Adjustments
REMINDER
1/8” min. gap
Clearance
Up / Down

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone]
11
12
Page 17
NOTES: If using the additional slots for mounting points, make sure that the floating frame is
fully level to the wall vertically and horizontally. Must use shims (commercially available) on
every slots being used to fill the void between the wall and the frame. Avoid over tightening the
screws as this would make the floating frame uneven.
Insert multiple M5 x 0.5 x 10mm Cup Point Set Screws on the left, right, and bottom side of the
mount. Adjust the LED Cabinets in sequential steps.
Additional
Slots
FILL VOIDS
WITH SHIMS

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
13
Page 18
LED Cabinet
Single unit configuration, 3 Wide by 2 High Video Wall, shown for clarity.
8 7 6 12 3 4 5
Example: 8X4 Array
SAMSUNG IFJ LED DISPLAY INSTALLATION MANUAL must be read in conjunction with
the recommended steps below. LED Cabinets to be handled by industry qualied professional.
Improper installation may cause damage to the LEDs.
Keyhole Slot
1. Install the first LED Cabinet from the center
bottom row of the mount.
2. Position the LED Cabinet into the keyhole slot
and slowly lower the cabinet.
3. Install adjacent or sequential cabinets and
expand outward.
4. Finetune the LED Cabinets. Adjust the set screws
located on the left, right, and bottom side of the mount.
A
N
T
I
-
S
T
A
T
I
C
G
L
O
V
E
S
Adjust set
screws

Installation Guide
SAM IFJ -
www.premiermounts.com | North America 800.368.9700 | International [phone]
14
Page 19
1. Place a Gap-It Tool to wedge between two LED Cabinets to prevent
abrupt release of the cabinets.
2. Slowly slide the Gap-It tool away from the LED Cabinets while lowering
into place. See Figure 2.
RECOMMENDATION ONLY: INSTALL WITH GAP-IT TOOL
Figure 2
Cautionary Advice:
Do not damage the
LEDs when lowering.
Figure 1
SLOWLY
PREMIER MOUNTS IS NOT RESPONSIBLE FOR ANY IMPROPER
HANDLING OF THE LED CABINETS.

Installation Guide
- SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
15
Page 20
3X3
4X4
5X5
Cover PCB
Flat Head Screw
All components within this page is supplied with the LED Cabinet (by others).
LED Diode
PCB
Cabinet
PET
Sheet
0~0.5mm
IMPORTANT: SECURE THE LED MODULES
The LEDs must be perfectly installed without any noticeable seams,
black bars, or imperfection of the LED modules. Modules must be in
locked position before moving forward.
1. Install the PET Sheet around the boundary of the entire video
wall array as shown below.
2. Secure using the Cover PCB and Flat Head Screw.
Boundary
PET Sheet