Premier Mounts PSPK User manual

PSPK PSPK
Installation Instructions Installation Instructions
IN-PSPK.R1
SPEAKER MOUNT INSTALLATION INSTRUCTIONS
Each hardware pack contains the following:
8-32 Round
Key Hole Nut
(Qty 1)
#12 x 1-3/4”
Self Tapping
Screw (Qty 2)
8/32 x 5/8”
Machine
Screw (Qty 1)
M5 x 1/8”
Plastic
Washer
(Qty 1)
#12-14
Alligator Plastic
Anchor
(Qty 2)
1/4” -20 x
1/2” Machine
Screw (Qty 2)
#8 x 3/4”
Self Tapping
Screw (Qty 1)
M4 x 8mm Flat
Head Machine
Screw (Qty 1)
1/4” -20 x
7/8” Machine
Screw (Qty 1)
#12 x 3/4”
Self Tapping
Screw (Qty 2)
M5 x 20mm
Machine Screw
(Qty 1)
Allen Wrench
(Qty 1)
IMPORTANT
Please read the instruction sheet prior to installation. This speaker mount was designed solely for the
mounting of small speakers weighing less than 10lbs. The manufacturer is not responsible for the damage
that will occur if speakers weighing more than 10lbs. are used.
Single Hole Mounting
1. Most satellite speakers will require the use of the M5 x 20mm machine screw used in combination with the M5 x 1/8”
plastic washer. The plastic washer is used as a spacer between the threaded insert and the speaker mount post
(Figure 1).
NOTE: It is critical the M5 plastic washer is used correctly, otherwise the threaded insert may pull out from the
speaker housing.
2. Once the proper configuration is determined, secure the post to the speaker.
3. Utilize the M4 x 8mm flat head machine screws (Figure 2).
4. Check the size of the hole and make sure the 8-32 x 5/8” machine screw, the 1/4”-20 x 1/2” machine screw, the
1/4”-20 x 7/8”, or the M5 x 20mm fits inside (Figure 3).
5. When the correct size is determined, place the screw through the speaker post and attach to the rear of the speaker
enclosure.
NOTE: If the screw does not tighten properly, use the M5 x 1/8” plastic washer to tighten it up.
Figure 1 Figure 2 Figure 3
Key Hole Mounting
6. If your speaker has a factory key hole design, you will use the 8-32 x 5/8 machine screws in
combination with the 8-32 round key hole nut.
7. Loosely pre-assemble the speaker mount post with the 8-32 x 5/8” machine screw and key hole nut
(Figure 4).
NOTE: Be sure the key hole nut is installed with the knurled edge toward the post.
8. Engage the key hole nut into the key hole slot, as shown.
9. Put tension on the assembly by gently pulling back on the speaker mount post while tightening the
8-32 x 5/8” machine screw (Figure 4).
10.The key hole nut will engage on the housing in the key hole slot.
11.If the post does not tighten securely against the housing , it will be necessary to use the M5 x 1/8” plastic washer as
a spacer under the head of the 8-32 x 5/8” machine screws (Figure 4).
M5x1/8”
Plastic Washer
M4x8mm Flat Head
Machine Screw
M5x1/8”
Plastic Washer
8-32x5/8”
Machine Screw
¼”-20 x 7/8”
Machine Screw
M5x20mm
Machine Screw
Mounting Post
P
lease Turn Over
12

PSPK PSPK
Installation Instructions Installation Instructions
IN-PSPK.R1
3 4
Figure 4
12. Find the best mounting configuration that matches your speaker enclosure. Four-hole speaker mount
patterns can be accomodated by positioning the speaker plate diagonally (Figure 5).
13. Using the 1/4”-20 x 1/2” machine screws, install the speaker plate and secure the speaker enclosure.
NOTE: Do not drill or screw into the speaker where you could possibly damage the internal components.
14. For Self Tapping Screws - Drill the holes using a 1/8” drill bit. This hole should not be drilled no more
than 1/2” depth (Figure 6).
Figure 5 Figure 6
Mounting Surfaces
The mounting hardware for three different surface applications is supplied. You will need to determine what style hardware
will work best with your mounting surface. Always use caution when drilling into a wall or ceiling. Make sure to avoid all
electrical and water lines.
WOOD SURFACE – Figure 7
1. Using a stud finder, locate the wood stud or framing member. Using a pick or small drill bit, locate the
center of the wood stud. Be careful doing this, as you dont want to go any wider than the
width of the wall plate (wall plate will cover any extra holes).
2. Using the wall plate as a template, mark a hole position on mounting surface.
NOTE: In-wall mounting applications position mounting holes in a vertical pattern.
3. Drill holes through the drywall and into the wood stud using a 1/8” drill bit.
4. These holes should be drilled 1-7/8” deep.
5. After the holes are drilled, mount the wall plate using the #12 x 1-3/4” self tapping screws.
DRYWALL SURFACE – Figure 8
1. Locate the best mounting location in the ceiling of wall. Using the wall plate as a template, mark the
hole position on the mounting surface.
NOTE: In wall mounting applications position mounting holes in a vertical pattern.
2. Drill holes in the drywall using a 5/16” drill bit.
3. Once the holes are drilled, insert the alligator anchor into the holes. Make sure the anchor is flush with
the wall and/or ceiling surface.
4. With the anchors in place, mount the wall plates using the #12 x 1-3/4” self tapping screws.
CONCRETE SURFACE – Figure 9
1. Using the wall plate as a template mark a hole position on mounting surface.
NOTE: In wall mounting applications position mounting holes in a vertical pattern.
2. Drill holes in the solid concrete or hollow block using a 5/16” masonry bit. Once the holes are drilled,
insert the #12-14 wall anchors into the holes, making sure the anchor is flush with the surface of the wall.
3. With the wall anchors in place, mount the wall plate using the #12 x 1-3/4” self tapping screws.
Figure 7 Figure 8 Figure 9
Extension Mounting
1. Install 2-1/2” extension portion of the
speaker mount to the wall plate.
2. Secure the setscrew to hold the
extension in place with the weight of
the speaker attached (Figure 10).
Low Profile Mounting
1. Install the link set portion of the
speaker mount to the wall plate or
2. Secure the setscrew to hold the
extension in place with the weight
of the speaker attached (Figure 11).
Speaker Mounting
1. Install the speaker with the
speaker post or 2-hole plate
attached.
2. Secure the setscrew to hold
the extension in place with
the weight of the speaker
attached (Figure 12).
Figure 10 Figure 11 Figure 12
M5x1/8” Plastic
Washer
8-32x5/8”
Machine Screw
Mounting Post
Keyhole
8-32 Round Key
Hole Nut
¼”-20” x ½”
Machine Screw
(Qty 2)
#12 x ¾”
Self Tapping
Screw (Qty 2)
#12 x ¾”
Self Tapping
Screw (Qty 2)