ICW UL182 OHAP User manual

Page 1
OVERHEAD ARM INSTALLATION
OVERHEAD ARM INSTALLATION 01/20/16 pjm
Page 1 of 4
MAXIMUM LOAD CAPACITY:
28 LBS (12.7 KG)
ATTACH TRACK ADAPTERS
Attach 4 track adapters
to back of wall plate
by threading socket
head screws from
front of wall plate
into track adapters.
Loosely tighten
with 3/16” hex key.
Insert screws
from front
ATTACH WALL PLATE TO TRACK
Slide track adapters
into track from
either top or bottom.
Position wall plate to
desired location on
track. Firmly tighten
wall plate screws
with 3/16” hex key.
ATTACH VESA to MONITOR
Track
adapters
Wall
plate
Attach VESA to monitor using
the four 4mm screws provided.
MOUNT OVERHEAD ARM
Slide overhead arm into
wall plate clamps. Firmly
tighten clamp screws on
left side with 3/16” hex key.
To adjust rotation tension
of arm, tighten or loosen
screws on right side of
clamps.
Clamp
screws
Tension
screws
Wall plate
clamps
MOUNT WALL TRACK TO WALL
Using a Phillips
drive, remove
plastic cap on
one end of track.
Save this cap to
put back on when
track installation
is complete.
Locate the wall stud and mark the top center hole of
the Wall Track. Drill a 11/64 pilot hole, insert a #14
screw and tighten slightly. Using a level, mark the 9
lower holes in the center of the track, drill pilot holes
and then insert the #14 screws. Use all 10 screws.
NOTE: #14 Wood screws are supplied with unit. If
installing into metal studs, you will need to replace
these with proper metal stud fasteners. All hardware
used to secure track mount must have a proper
countersunk head.
UL182-OHAT
Wall Track Mount
UL182 OHAP
Wall Plate Mount
Wall Plate instructions on p.3

OVERHEAD ARM INSTALLATION 01/20/16 pjm
OVERHEAD ARM INSTALLATION
Page 2 of 4
OVERHEAD ARM INSTALLATION
ATTACH VESA WITH MONITOR
TO ARM
• Slide posts
of VESA plate
into the EV65 joint assembly.
• Insert provided socket head cap
screws into both sides of EV65
and tighten.
• Use knob to adjust tilt friction.
NOTE: Monitor is
not shown in order
to illustrate mounting
detail.
Use cord provided inside overhead arm
to pull wires through to the monitor.
• At track end of overhead arm, grasp cord
and pull down.
• Loop cord around wires.
• At monitor end of overhead arm, grasp
cord and pull wires through.
PULL WIRES THROUGH ARM
Loop cord around
wires at this end
Pull wires through
arm at this end
RUN WIRES THROUGH ULTRA 182 TO MONITOR
• The Ultra 182 cover plate is spring loaded. Loosen cover
platescrewsonsideofarmjustenoughtotwiresthrough
gap. Run wires loosely between cover plate and arm.
Wires can be run on either or both sides of the arm.
• Connect wires from Ultra 182 to monitor.
• Move monitor through full range of motion to
allow for correct amount of slack in wire.
Pull excess wire back through
Ultra 182 and overhead arm.
• Push cover plate against Ultra 182
arm and tighten screws, being
careful not to pinch wires.
REATTACH BEAUTY CAPS
Reattach plastic
caps to top and
bottom of track.
RUN WIRES
THROUGH TRACK
• Pull slack wire down
from overhead arm.
• Run wires through
center of track.
• Reattach track cover.
Track cover
Wires run through
center of track and
out the bottom
ATTACH HANDLE TO VESA PLATE
Center wires
between screw
holes on VESA
plate where handle
attaches. Using
socket head
screws provided,
attach handle to
VESA plate,
securing wires
between handle
and back of VESA
plate.

OVERHEAD ARM INSTALLATION 01/20/16 pjm
OVERHEAD ARM INSTALLATION
Page 3 of 4
OVERHEAD ARM INSTALLATION
MOUNT WALL PLATE TO WALL
MAXIMUM LOAD CAPACITY:
28 LBS (12.7 KG)
CENTER MOUNTED ON ONE STUD (16” or 24” spaced studs)
Locate a stud in the wall where wall plate will be mounted, determine desired height,
and mark the top (center) hole.
For wood studs:
• Drill 11/64” pilot hole and insert #14 wood screw (provided), tighten slightly.
• Using a level, mark the remaining 3 holes in the center of the plate and one hole in
each edge of the plate. Remove the plate and pilot each hole.
• Following the Snaptoggle installation instructions on next page, install Snaptoggles
inthetwoedgeholes.Replaceplateusing4#14screwsand2¼-20x2-1/4”at
Phillips head machine screws. Check level and tighten all 6 screws.
For steel studs:
• Drill 11/64” pilot hole, then follow Snaptoggle installation instructions on next page.
• Attachplateusing¼-20x2-1/4”atPhillipsheadmachinescrew,tightenslightly.
• Using a level, mark the remaining 3 holes in the center of the plate and one hole in
each edge of the plate.
• Remove the plate, pilot, and install Snaptoggles in all 5 holes.
• Replaceplateusing6¼-20x2-1/4”atPhillipsheadmachinescrews.Checklevel
and tighten all 6 screws.
SPANNING TWO STUDS (16” spaced studs only)
Locate two studs in the wall where wall plate will be mounted, determine desired
height, using a level, mark the top hole in each edge of the plate.
For wood studs:
• Drill 11/64” pilot holes and insert 2 #14 wood screws (provided), tighten slightly.
Using a level; pilot the remaining 4 holes in the edges of the plate and insert #14
screws. Check level and tighten all 6 screws.
For steel studs:
• Drill 11/64” pilot holes then follow Snaptoggle installation instructions on next page,
attachplateusing2¼-20x2-1/4”atPhillipsheadmachinescrews,tightenslightly.
Using a level; mark the remaining 4 holes in the edges of the plate.
• Remove the plate, pilot, and install Snaptoggles in all 4 holes.
• Replaceplateusing6¼-20x2-1/4”atPhillipsheadmachinescrews.Checklevel
and tighten all 6 screws.
UL182-OHAP
Wall Plate Mount

OVERHEAD ARM INSTALLATION 01/20/16 pjm
Page 4 of 4
OVERHEAD ARM INSTALLATION
AFTER MOUNTING ARM TO WALL PLATE,
FOLLOW INSTRUCTIONS TO MOUNT MONITOR
AND MANAGE CABLES.
MOUNT OVERHEAD ARM ATTACH COVER PLATE
Slide overhead arm
into wall plate clamps.
Snap cover plate onto
wall plate.
Attach using 10-
24x3/8” Phillips head
machine screws.
Wall
plate
clamps
Firmly tighten clamp
screws on left side of
clamp with 3/16” hex
key. To adjust rotation
tension of arm, tighten
or loosen tension
screws on right side
of clamps.
Tension
screw
Clamp
screw
The plastic straps and cap washer are positioning and
retention elements only. They do not otherwise function as
anchoring elements. Holding is dependent only on a metal
bolt to metal channel connection. The SnapToggle anchor
complieswithallexistingrecodesforcriticalapplications.
Handle Cap Straps Anchoring
Channel
Drill 1/2” hole. Hold metal
channelatalongside
plastic straps and slide
channel through the hole.
Minimum clearance behind
wall is 1-7/8”
Hold ends of straps together
between thumb and fore-
ngerandpulltowardyou
until channel rests behind
wall. Ratchet cap along straps
withotherhanduntilangeof
capisushwithwall.
Place thumb between straps
at wall. Push thumb side
to side, snapping off straps
levelwithangeofcap.
Snap Toggle Instructions