Presenza QK81C User manual

USER MANUAL
MANUEL DE L’UTILISATEUR
MANUAL DEL USARIO
# QK81C
DUAL MOUNT SINGLE BOWL
STAINLESS STEEL SINK KIT
TROUSSE POUR ÉVIER À CUVETTE SIMPLE
EN ACIER INOXYDABLE, À DEUX OPTIONS D’INSTALLATION
JUEGO DE FREGADERO INDIVIDUAL
DE ACERO INOXIDABLE Y MONTAJE DUAL
Rev. 20201209

ENGLISH
2
QK81C
Table of Contents
Safety Information ................. 2
Warranty
One-Year Limited Warranty ........ 3
Warranty Claim Procedure ......... 3
Pre-Installation
Planning Installation ............. 4
Tools/Materials Required .......... 4
Parts Required .................. 4
Package Contents ............... 5
Installation
Undermount.................... 6
Topmount ...................... 9
Installing the Faucet ............ 11
Installing the Soap Dispenser ..... 12
Installing the Strainer ........... 13
Installing the Grid............... 14
Maintenance ..................... 14
Care and Cleaning ................ 15
Service Parts..................... 16
MANUEL DE L’UTILISATEUR ......... 17
MANUAL DEL USARIO .............. 32
Safety Information
CAUTION: Always wear safety goggles and gloves in order to avoid personal injury.
READ AND SAVE THESE INSTRUCTIONS
1. Unpack and inspect this product for chips, scratches, cracks, dents, and scuff marks. Do not install
this product if any damages or defects are identied.
2. Use this product only in the manner intended by the manufacturer. If you have any questions,
contact the manufacturer.
3. Installation work and plumbing must be done by qualied person(s) in accordance with all
applicable codes and standards.
4. Protect the entire surface during installation.

CONGLOMKB.COM
Please contact [email protected] or 1-877-333-0098 for further assistance.
ENGLISH
3
Warranty
ONE YEAR LIMITED WARRANTY
A thorough inspection must be made before installation and any damage must be promptly reported. Conglom Inc. will not be
liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation.
Conglom Inc. warrants this product to be free from defects in materials or workmanship for one (1) year from the date of
purchase. Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to us for all
warranty claims.
This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed
following the manufacturer’s instructions. It does not apply in the event of product damage due to the use of other
than genuine replacement parts, (Replacement parts may be obtained by e-mail at [email protected] or by calling
1-877-333-0098 between 8:30 am - 5:00 pm EST) installation error, abuse, misuse or improper care and maintenance
(whether performed by a plumber, contractor, service provider or member of the purchaser’s household). The warranty
excludes damage due to aggressive air or water conditions, harsh or abrasive cleaners and/or materials.
Under no circumstance shall Conglom Inc. be held liable for personal injury or property damage resulting from improper
installation or use of this product. Conglom Inc. will not be held liable for inconvenience caused by loss of use of this product,
costs incurred for labour or materials, removal and installation of replacement units, or any other incidental or consequential
damages. Costs relating to obtaining access for repair or replacement are the responsibility of the user.
Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole
examination, to be defective under normal use and service during the warranty period.
Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These
non-warrantable items include, but are not limited to:
- Improper installation not in accordance with manufacturer’s instructions.
- Dents and/or scratches incurred during shipping, handling, or installation.
- Change in colour or nish due to chemical usage.
- Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of
abrasive cleaners.
- Alterations made to the unit by the purchaser or installer.
- Damage caused by accidental impact, re, ood, freezing, and normal wear.
- Bends and warping caused by forced connections, overtightened ttings, and inadequate support during
installation.
- Damage caused by use of chlorine-based cleaners.
This warranty does not extend to commercial and institutional installation or use.
WARRANTY CLAIM PROCEDURE
If a claimable defect occurs or replacement parts are needed, please contact our customer service team at
[email protected] or 1-877-333-0098 (service available in English and French, Monday - Friday from 8:30 am - 5 pm EST).
Before you make your call, please ensure that you have:
- Model number or description.
- Proof of sale.
- Details regarding the defect and/or part number.
- Name(s) and address(es) of the owner and/or installer.

ENGLISH
4
QK81C
Pre-Installation
PLANNING INSTALLATION
You may choose to install this sink either below the counter (undermount) or above
the counter (topmount). You must install this sink in a counter at least 36 in. (914 mm)
wide with a solid surface that has a minimum thickness of 3/4 in. (19 mm).
Protect the entire surface of the product during installation to prevent damage.
UNDERMOUNT
TOPMOUNT
TOOLS/MATERIALS REQUIRED (NOT SUPPLIED)
Measuring tape Carpenter’s
square Wrenches (2)
Saber-saw or
Jig-saw Electric drill Pipe wrench
Sealant Pencil Thread Seal
Flathead
screwdriver Hacksaw Safety goggles
Safety gloves Phillips
screwdriver
PARTS REQUIRED (NOT SUPPLIED)
Tail pipe (1) Supply lines (2)

CONGLOMKB.COM
Please contact [email protected] or 1-877-333-0098 for further assistance.
ENGLISH
5
Pre-Installation (continued)
PACKAGE CONTENTS
Carefully check the package contents for damage and/or missing parts prior to installation. If there is
any damage or if you are missing parts, do not proceed with the installation. Report damage and/or
missing parts immediately to our customer service team at [email protected] or 1-877-333-0098
(Service available in English and French, Monday - Friday from 8:30 am - 5:00 pm EST). Please do not
dispose of packaging before you are satised with your new sink.
A
C
BD
GF
1A
E
H
Part Description Quantity
1A Sink template 1
A Stainless steel sink 1
B Bottom grid 1
C Strainer basket 1
D Drain assembly 1
E Faucet 1
F Soap dispenser 1
G Topmount clips 10
H Undermount clips 10

ENGLISH
6
QK81C
Installation
UNDERMOUNT INSTALLATION
UNDERMOUNT
NOTE: Undermount sinks are mounted from below the counter. If you are installing a topmount or “drop-in”
sink, please see “Topmount Installation”. It is highly recommended that undermounting be performed by a
professional installer. Improper installation will void the warranty. Sink template (1A) shows cut-lines for both
undermount and topmount installations. Review it carefully and follow the undermount cut-lines only to install the
sink under your counter.
PREPARING THE AREA CUTTING THE COUNTER
- Place the template (1A) on the desired
counter space surface. Keep in mind that
the typical setback is 3 1/2 - 4 in. (89 mm
- 102 mm) from the front of the counter to
the sink bowl (depending on the cabinet
structure, the counter overhang, the type of
sink bowl, and the deck size).
- Make sure the template (1A) is parallel to the
front of the counter.
CAUTION: Always wear safety goggles
and gloves when using power tools to
prevent personal injury.
- Ensure that the template (1A) is placed
so that the sink will clear all objects and
the mounting hardware can be installed.
Secure the template to the counter top using
masking tape.
- Place a support underneath the cut-out
portion of the counter to prevent it from falling
during cutting. Use an appropriate saw to cut
along the undermount cutline.
- Drill a 1-3/8 in. (35 mm) mounting hole for
your faucet.
- Drill a 1-1/4 in. (32 mm) mounting hole for
your soap dispenser.
1A
Typical Setback
3 1/2 - 4 in.
(89 mm - 102 mm)
Tape
Undermount installation
Fig. 1

CONGLOMKB.COM
Please contact [email protected] or 1-877-333-0098 for further assistance.
ENGLISH
7
Installation (continued)
TESTING THE FIT OF THE SINK
- Place the sink (A) underneath the cut-out
in the counter to test its t. Ensure that the
reveal is equal on all four sides when viewed
from above. Make adjustments to the cut-out
if necessary.
- When you are satised with the location of
the sink (A), mark the location of the edge
of the counter cut-out on top of the sink
and all around the sink ange underneath
the counter.
- Set the sink aside and proceed with the rest
of the installation.
A
Fig. 2
DRILLING THE HOLES FOR THE
UNDERMOUNT CLIPS
- On the underside of the counter, mark the
location of the ten holes for the undermount
clips (F). These holes should be equally
spaced around the sink ange outline as
shown below. They should be set back from
the sink ange outline by 5/8 in (15.8 mm).
- Using an electric drill with a 27/64 in.
(10.6mm) drill bit, drill each hole so that it is
9/16 in. (14 mm) deep. Use a drill bit depth
stop to ensure you do not drill through the
counter top.
CAUTION: Always wear safety
goggles and gloves in order to avoid
personal injury.
Undermount clip hole locations
(Underside of counter)
5/8 in
15.8 mm
Sink flange outline
Fig. 3

ENGLISH
8
QK81C
Installation (continued)
INSTALLING THE SINK
NOTE: Install the strainer according to "Installing the Strainer" instructions before completing this step.
- Press t the threaded anchor inserts into the holes drilled into the underside of the countertop. Use a bolt to
make this process easier if required.
- Loosely thread the undermount bolts and clips into the threaded anchor inserts and align them parallel to the
sink ange outline so they do not interfere with the placement of the sink.
- Place a small bead of silicone sealant (not included) around the outer top perimeter of the sink ange as
shown below.
- Carefully place the sink (A) into its location under the counter, lining up the sink with the sink ange outline.
- Carefully rotate the clips over the sink ange and gently tighten the bolts (see tightening sequence) to fasten
the sink. Recheck the alignment visually from above and make nal adjustments if necessary, then tighten all
the bolts.
- Wipe away any excess silicone and, for best results, allow the bond to rest undisturbed for 8 hours.
- Install faucet, soap dispenser, and sink strainer as per instructions in this manual.
- Install all other plumbing as per manufacturer’s instructions.
A
A
9
6 2 4
3 5 1
7
810
Tightening sequence for clips
Bolt
Silicone
Sealant
Threaded
anchor inserts
Counter
Clip
Fig. 4

CONGLOMKB.COM
Please contact [email protected] or 1-877-333-0098 for further assistance.
ENGLISH
9
Installation (continued)
TOPMOUNT INSTALLATION
NOTE: Topmount sinks are dropped into the counter from above. If you are installing an undermount sink,
please see “Undermount Installation”. Sink template (1A) shows cut-lines for both undermount and topmount
installations. Review it carefully and follow the outer topmount cut-lines only to install the sink over your counter.
PREPARING THE AREA CUTTING THE COUNTER
- Center the template (1A) on the counter
so that it is parallel to the front of the
counter (ensuring that it will not interfere
with the inside structure of the cabinet or
the counter). It must clear the overhang
of the counter and the front inside face of
the cabinet.
- Keep in mind that the typical setback is 3 1/2
- 4 in. (89 mm - 102 mm) from the front of
the counter to the sink bowl (depending on
the cabinet structure, the counter overhang,
the type of sink bowl, and the deck size).
- Ensure there is adequate clearance to
install the mounting hardware underneath
the counter.
CAUTION: Always wear safety goggles
and gloves when using power tools to
prevent personal injury.
- Secure the sink template (1A) to the counter
top using masking tape.
- Place a support underneath the cut-out
portion of the counter to prevent it from
falling during cutting. Use an appropriate saw
to cut along the topmount cutline.
- Insert the sink (A) into the cut-out in the
counter to test the t. Make adjustments to
the cut-out, if necessary.
Topmount installation
1A
Typical Setback
3 1/2 - 4 in.
(89 mm - 102 mm)
Tape
Fig. 5

ENGLISH
10
QK81C
Installation (continued)
INSTALLING THE SINK
NOTE: Install the faucet according to the "Installing
the Faucet" instructions before completing this step.
Install the strainer according to "Installing the Strainer"
instructions before completing this step.
- Install the topmount clips and bolts into the
clip channels of the sink as shown in gure 6.
Use gure 8 to determine how many clips to
install into each channel.
- Apply silicone sealant (not included) around
the underside of the ange of the sink (A) on
all four sides or all around the top edge of the
cutout in the countertop.
- Carefully lower the sink (A) into the counter,
ensuring that the topmount clips (G) do not
catch on the counter edges. Ensure that the
sink (A) is centered and parallel with the front
of the counter.
- Adjust each topmount clip along the channels
so that they are evenly spaced around
the sink (A).
- Rotate the topmount clips such that they
engage the counter, and tighten the screws
progressively (see gure 8 tightening
sequence) until the sink ange is ush with
the counter. Check the alignment as you
tighten so that the front of the sink (A) is
parallel to the front of the counter. Adjust and
re-tighten if necessary. Do not overtighten.
NOTE: If the ange is not ush with the counter, use a
heavy weight or clamp from above to press the ange
down until the sealant sets.
- When nished, wipe away any excess sealant
and allow it to set before proceeding with the
rest of the installation.
A
Tightening sequence for clips
A
Clip channel
9
6 2 4
3 5 1
7
810
A
Clip Bolt
A
Silicone
Sealant
Clip Bolt
Counter
Clip
Fig. 6
Fig. 7
Fig. 8

CONGLOMKB.COM
Please contact [email protected] or 1-877-333-0098 for further assistance.
ENGLISH
11
Installation (continued)
INSTALLING THE FAUCET
- Connect the sprayer head (1) to the sprayer head
connector (2).
- Remove the gasket (3), metal washer (4), and
retaining nut (5) from the mounting shank of
the faucet.
- Insert the faucet hose and the mounting shank
through the faucet hole in the sink and rest the
faucet on the sink.
- From underneath, secure the faucet to the
sink with the gasket (3), metal washer (4), and
retaining nut (5).
- Tighten the retaining nut (5) by hand until it is
snug. Use a wrench to tighten it down. Gently
tighten the two screws on the retaining nut. Do not
overtighten.
- Connect the main water supply outlet (6) to the
sprayer hose (9) using the quick connector (7) as
shown. Connect the male quick connector tting
(8) to the female quick connector tting (7) until it
locks. Lightly tug on the quick connect ttings to
ensure they are fully engaged.
- Fully retract the sprayer hose (9). Install the
counterweight (10) about 2 in. (50 mm) from the
bottom on the side closest to the sprayer head (1).
There should be no slack in the hose and it should
retract freely.
- Attach and hand tighten the supply lines (not
supplied) onto the faucet inlet ttings. Use two
wrenches to tighten the two ends together.
NOTE: Failing to use two wrenches can damage the
faucet and void the warranty. Do not overtighten. It is
helpful to have a second person hold the faucet in place
while tightening the mounting nuts. Please ensure that
none of the supply lines are kinked during installation.
QUICK CONNECTOR
Female Quick
Connector
Fitting (7)
Male Quick Connector
Fitting (8)
Spring
Sprayer Head
Connector (2)
Sprayer
Head (1)
Faucet body
Gasket (3)
Retaining
Nut (5)
Metal
Washer (4)
Mounting
Shank
Screws
Counterweight (10)
Hot / Cold
Supply Lines
Supply Line
Inlet Fittings Sprayer Hose (9)
Male Quick
Connector Fitting (8)
Female Quick
Connector Fitting (7)
Main Water
Supply Outlet (6)
Supply Line
Inlet Fittings
1/2" NPS thread
1/2" FIP
Water Supply
Line Compatible
Fig. 9
Fig. 10

ENGLISH
12
QK81C
Installation (continued)
INSTALLING THE SOAP DISPENSER
CAUTION: This unit is designed for use
with household liquid soap only. Using
any other soap or chemicals in this unit
may damage the dispenser and void
the warranty.
- Attach straw (10) to dispenser head (9) and
set them aside.
- From top of sink, install gasket (12) and
dispenser body (11).
- From under the sink, secure dispenser body
(11) with the other gasket (12) and locknut
(13). Install bottle (14) into dispenser
body (11).
- Pour soap (not included) into the bottle
(14) through the dispenser body (11)
from above.
- Fit dispenser head (9) onto dispenser
body (11).
Sink (A)
Dispenser head (9)
Straw (10)
Dispenser body (11)
Gasket (12)
Gasket (12)
Locknut (13)
Bottle (14)
Fig. 11
Fig. 12

CONGLOMKB.COM
Please contact [email protected] or 1-877-333-0098 for further assistance.
ENGLISH
13
Installation (continued)
INSTALLING THE STRAINER
NOTE: If you are installing a garbage disposer (not
supplied), do not install the strainer.
- Apply plumbing putty or silicone sealant (not
included) to the top side of the drain opening.
- Insert the strainer body (15) into the
drain opening and press it down until it is
evenly seated.
- Assemble the rubber gasket (16), ber washer
(17) and strainer locknut (18) onto the strainer
body (15) from underneath the sink. Hand
tighten the strainer locknut (18) until it is snug.
Do not overtighten.
- Insert the plastic ange (19) into the ange-end
of the tailpipe (20) (not supplied) then secure
the tailpipe to the strainer body using the
connecting nut (21). Tighten the connecting nut
(21) until it is snug. Do not overtighten.
- Remove excess sealant from around the
drain opening.
Fig. 13
DRAINAGE
The tailpipe (not supplied) previously installed to the drain can now be connected to your household plumbing. In
some cases, your household plumbing will have to be modied to ensure proper drainage. If so, please consult a
licensed plumber to complete needed modications.
SUPPLY LINES (NOT INCLUDED)
Connect the supply lines to your home’s water supply as per manufacturer’s
instructions.
Open the hot and cold water supply valves and check to make sure they have
been installed to appropriate inlet ports. Check for leaks. Run hot and cold
water uninterrupted for about one minute to remove any residue from the lines.
Strainer Body (15)
Sealant
Sink (A)
Rubber Gasket (16)
Fiber Washer (17)
Strainer Locknut (18)
Plastic Flange (19)
Tailpipe (20)
(not supplied)
Connecting Nut (21)
Strainer Basket (22)

ENGLISH
14
QK81C
Installation (continued)
INSTALLING THE BOTTOM GRID
- Ensure that the strainer basket (C) is
already in the sink (A) before placing the
bottom grid (B).
- The bottom grid (B) must be positioned with
the rubber supports down. Tilt the grid up so
it is at an angle, slide it into the sink (A), and
place it so that it is sitting at on the bottom
of the sink.
NOTE: Faucet and soap dispenser not shown for clarity.
AC
B
Maintenance
CARTRIDGE REPLACEMENT
- Turn off the water supply to the faucet.
- Unscrew the handle lever (23). Loosen the set
screw (25) with the hex key and remove the
handle body (30).
- Gently unscrew the decorative cap (29) and
retaining nut (28).
- Pull the cartridge (27) out of the faucet
body (26) and replace it with a new
ceramic cartridge. Ensure new cartridge
is seated properly with the locating pins in
appropriate place.
- Secure the cartridge in place using the
retaining nut (28).
- Gently tighten the retaining nut (28) using a
wrench. Do not overtighten.
- Reinstall the decorative cap (29). Slide the
handle body (30) back onto the cartridge and
make sure it rotates freely. Secure the handle
body (30) in place using the set screw (25)
and reinstall the handle lever (23).
- Turn the water supply to the faucet back on.
- Operate the faucet to make sure everything
works correctly and check for leaks.
Handle Lever (23)
Decorative Cap (29)
Retaining Nut (28)
Cartridge (27)
Handle Body (30)
Faucet Body (26)
Set screw (25)
O-Ring (24)

CONGLOMKB.COM
Please contact [email protected] or 1-877-333-0098 for further assistance.
ENGLISH
15
Care and Cleaning
Your sink is manufactured with the highest grade stainless steel and will provide you many years
of enjoyment with the proper care.
Do: Do Not:
- After use, always rinse your sink with tap
water to dilute and remove deposits.
- Towel dry the sink after use whenever
possible to prevent water spots. Should
water spots occur, clean with a mild
solution of vinegar and water followed by a
thorough rinse.
- Use liquid soap, a general household
cleaner, or a weak solution of vinegar and
water for regular cleaning.
- Only use plastic scouring pads
recommended for use in stainless steel
sinks, and only use them in the bowl of
the sink. Scrub in the direction of the grain
(original polish lines).
- Do not allow any food, detergent, soap or
grease to dry or sit for extended periods of
time on the surface of the sink.
- Never use abrasive cleaning products, as
they will dull and scratch the nish.
- Do not use scouring pads on the deck, as
they will dull the nish.
- Never use steel wool pads or leave steel/
cast iron pans in your sink for extended
periods of time, as they will leave iron
particles on the sink, which can cause
corrosion.
- Never use chlorine-based cleaners in your
new sink, they could lead to rust spots
and discolouration. If you must use them,
rinse sink thoroughly with fresh water
immediately after use.
- If any chemicals or glue make contact with
the sink during installation, wipe clean and
rinse thoroughly with fresh water.
SCRATCH, SPOT, AND BLEMISH REMOVAL AND SURFACE RESTORATION:
Little rust spots and blemishes that periodically appear in the sink are typically the result of the
steel interacting with the chemicals found in the vast spectrum of substances that sinks are
commonly exposed to. They may also get transferred from other objects placed or left in the sink.
Scratches are the result of regular wear and tear.
To remove scratches, spots, and blemishes from the sink, rub them with a non-metallic scouring
pad (e.g. Scotch-Brite®) combined with a mild abrasive cleaner (e.g. Vim® or Barkeeper’s Friend®).
Always rub the surfaces in the direction of the grain of the steel. When nished, rinse the sink with
water and dry it with a towel to allow the sink to form a protective outer layer. This procedure can
also be used to renew all of the surfaces of the sink.

ENGLISH
16
QK81C
Service Parts
If you are missing parts or require replacement parts, please contact our customer service team at
[email protected] or 1-877-333-0098 (Service available in English and French, Monday - Friday from
8:30am - 5pm EST). Identify the required part(s) and have the part number(s) ready.
B C
F
D
A
E
G
Part Description Code Quantity
A Bottom grid QHS266 1
B Ceramic cartridge QHL216 1
C Sprayer head QHL223 1
D Topmount clip QHS270 10
E Undermount clip QHS271 10
F Strainer basket QHS268 1
G Strainer assembly QHS269 1

CONGLOMKB.COM
Veuillez contacter [email protected] ou 1-877-333-0098 pour toute assistance supplémentaire.
FRANÇAIS
17
Table des matières
OWNER’S MANUAL ................. 2
Consigne de sécurité .............. 17
Garantie
Garantie limitée d’un an........... 18
Procédure de réclamation ......... 18
Préinstallation
Outils/Matériaux requis ........... 19
Pièces requises ................. 19
Contenu de l’emballage........... 20
Installation
Installation sous le comptoir ....... 21
Installation sur le comptoir ........ 24
Installation du robinet ............ 26
Installation du distributeur à savon .. 27
Installation de la crépine .......... 28
Installation de la grille ............ 29
Entretien ........................ 29
Soin et nettoyage ................. 30
Pièce de rechange ................ 31
MANUAL DEL USARIO .............. 32
Consigne de sécurité
AVERTISSEMENT: Toujours porter des lunettes et des gants de sécurité pendant l’installation
an d’éviter les blessures.
LIRE ET CONSERVER CES DIRECTIVES
1. Vérier soigneusement l’unité avant l’installation pour vous assurer qu’elle ne comporte aucun
dommage. Après avoir déballé votre unité, vérier s’il y a des rayures, des ssures, des bosses ou
des éraures. Si des dommages sont notés, ne pas installer.
2. Cet appareil ne peut être utilisé autrement que pour l’usage prévu par le fabricant. Consulter le
fabricant pour toutes questions concernant l’appareil.
3. Votre installation doit être conforme à tous les codes de bâtiment locaux pour la plomberie. Veiller à
ce qu’un ouvrier qualié effectue ou approuve votre installation de plomberie.
4. Protéger la surface lors de l’installation.

QK81C
FRANÇAIS
18
Garantie
GARANTIE LIMITÉE D’UN AN
Inspecter minutieusement le produit avant l’installation et signaler tout dommage sans délai. Nous ne serons pas
responsables des défaillances ou des dommages qui auraient dû être découverts ou évités par une inspection adéquate et
des essais avant l’installation.
Conglom Inc. garantit ce produit contre tout défaut dans les matériaux ou la fabrication, pour une période d’un (1) an à
compter de la date de l’achat. Une preuve d’achat (facture d’achat originale) du consommateur/acheteur original devra
accompagner toute réclamation faite à Conglom Inc.
Cette garantie est non transférable et sera nulle si l’unité est enlevée de son installation initiale ou si elle n’est pas installée
suivant les spécications du fabricant. Elle ne s’applique pas dans l’éventualité de dommages causés au produit suite à
l’utilisation de pièce(s) de rechange autre que les pièces originales Conglom Inc., (les pièces de rechange peuvent être
obtenus en nous écrivant un courriel à [email protected] ou en appellant au 1-877-333-0098 entre 8h30 et 17h00,
H.N.E.) une erreur d’installation, l’abus, l’utilisation ou l’entretien incorrecte et le service incorrects (qu’ils soient effectués
par un plombier, un entrepreneur, une entreprise de service ou un membre de la famille de l’acheteur). La garantie exclut les
dommages causés par des conditions agressives d’air ou d’eau, des nettoyants ou des matériaux rudes et/ou abrasifs.
Nous ne pouvons en aucun cas être tenus responsables pour toute blessure corporelle ou tout dommage matériel résultant
d’une mauvaise installation ou utilisation de ce produit. Nous ne serons pas tenues responsables de l’incapacité d’utiliser
cette unité, des inconvénients, des coûts encourus pour la main d’œuvre, des matériaux, de l’enlèvement et de l’installation
des unités de remplacement ou d’aucun autre dommage causé par un incident ou accessoire. Les coûts encourus pour
obtenir l’accès pour la réparation ou le remplacement sont la responsabilité de l’utilisateur.
Nos obligations se limitent à la réparation ou au remplacement de l’unité (selon notre choix) qui peut s’avérer, selon notre
examen unique, être défectueuse sous l’utilisation et le service normaux pendant la période de garantie. Nous pouvons
émettre un crédit au montant de la valeur de la facture du produit défectueux (ou d’un pourcentage de ce montant selon
l’usure) tenant lieu de la réparation ou du remplacement.
Toute défectuosité de l’unité qui ne peut être liée à un défaut de matériel ou de fabrication n’est pas couvert par cette
garantie. Ces conditions non garanties incluent, mais ne se limitent pas aux suivantes :
- Une mauvaise installation non conforme aux instructions du fabricant.
- Les bosselures, bosses et rayures causées pendant l’expédition, la manutention ou l’installation.
- Changement de la couleur ou du ni en raison de l’usage d’un produit chimique.
- Les dommages causés par le non-respect des directives de soin et de nettoyage, y compris les dommages causés
par l’utilisation de produits nettoyants abrasifs.
- Toute modication apportée à l’unité par l’acheteur ou l’installateur.
- Dommages en raison d’un impact accidentel, du feu, d’une inondation, du gel et de l’usure normale.
- Courbures et déformations provoquées par des raccordements forcés, des xations trop serrées et un support
inadéquat pendant l’installation.
- Dommages causés par l’utilisation de produits nettoyants à base de chlore.
Cette garantie ne s’applique pas à l’utilisation ou l’installation à des ns commerciales ou institutionnelles.
PROCÉDURE DE RÉCLAMATION
Si un défaut couvert par la garantie se produit ou que vous avez besoin des pièces de rechange, contacter notre service à la
clientèle au [email protected] ou au 1-877-333-0098 (lundi au vendredi, 8h30 à 17h, H.N.E.).
Avant d’appeler, veuillez-vous assurer d’avoir en main :
- Numéro de modèle ou une description.
- La preuve d’achat.
- Les détails concernant le défaut et/ou le numéro de la pièce de rechange.
- Le nom et l’adresse du propriétaire et/ou de l’installateur.

CONGLOMKB.COM
Veuillez contacter [email protected] ou 1-877-333-0098 pour toute assistance supplémentaire.
FRANÇAIS
19
Préinstallation
PLANIFICATION DE L’INSTALLATION
Vous pouvez choisir d’installer cet évier soit par montage sous le comptoir (à partir du
dessous du comptoir) ou sur le comptoir (à partir du dessus du comptoir). Vous devez
installer cet évier seulement dans un comptoir d’au moins 914 mm (36 po) de largeur
avec une surface solide d’une épaisseur minimale d’au moins 19 mm (3/4 po).
Protéger la surface entière du produit lors de l’installation pour éviter tout dommage.
DESSOUS
DESSUS
OUTILS/MATÉRIEL REQUIS (NON INCLUS)
Ruban à mesurer Équerre Clés (2)
Scie alternative ou
scie sauteuse
Tournevis
électrique Clé à tuyau
Mastic Crayon Ruban
d’étanchéité
Tournevis plat Scie à métaux Lunettes
de sécurité
Gants de sécurité Tournevis
Phillips
PIÈCES REQUISES (NON INCLUSES)
Tuyan de
vidange (1)
Tuyaux
d’alimentation (2)

QK81C
FRANÇAIS
20
Préinstallation (suite)
CONTENU DE L’EMBALLAGE
Vérier soigneusement que l’unité ne comporte aucun dommage ou pièces manquantes avant
l’installation. S’il y a des dommages ou s’il manque des pièces, ne pas procéder à l’installation.
En cas de dommages ou de pièces manquantes, communiquer avec le service à la clientèle au
[email protected] ou 1 877 333-0098 (service en anglais et français, du lundi au vendredi, 8 h 30 et
17 h, HNE). Ne pas vous débarrasser de l’emballage avant d’être satisfait de ce produit.
A
C
BD
GF
1A
E
H
Pièce Description Quantité
1A Gabarit pour l’installation 1
A Évier en acier inoxydable 1
B Grille métallique 1
C Panier de crépine 1
D Assemblage de la crépine 1
E Robinet 1
F Distributeur à savon 1
GAttaches de xation par le dessus 10
HAttaches de xation par le dessous 10