Presidential Billiards FORD User manual

1
FORD BILLIARD TABLE
INSTALLATION INSTRUCTIONS
Tools required by the installer:
3/8” Drive ratchet and Extension Small Hammer
1/2” and 9/16” Sockets for above Tape Measure
1/2” and 9/16” Combo end wrench Utility Knife
# 2 and # 3 Phillips screwdriver 1/8” & 3/16” Drill bits
Electric drill/ driver
Prior to installation of the table please check for damaged or missing parts. Call Presidential Billiards at 866-
728-2253 if there is a problem. The hardware is packed in several different packets. Each packet represents a
step number. This coincides with the steps in this installation instruction and will hopefully reduce your time to
verify what hardware is required and where. It is suggested that you retain the bolts in their respective packets
for ease of installation.
STEP 1 LEG ASSEMBLY
1.1 Place leg assemblies in the location selected for the table.
1.2 Attach leg bars to legs using nut in bar box. Tighten using crescent wrench.
1.3 Build picture frame beam assembly on a level surface. Attach slate beams and end beams to long beam
using 3/8”x 5" bolt, barrel nut and washer. Attach leg beam using 5/16”x 3 1/2" bolt and washer.
Repeat for other long beam. Attach top stretcher to beams using 5/16”x 1 3/4” bolt and washer. Square
and tighten all bolts on frame.
1.4 Place picture frame assembly on legs. Attach to leg beams using 3/8 x 5" bolt, washers and nut. If frame
assembly will not fit over legs, loose one side of assembly until it falls over legs. Recheck square.
1.5 Attach wings using 5/16” x 3 1/2" bolts and washers for the long beams.
STEP 2 INSTALL THE SLATE
2.1 Level the table to the floor. Place the three pieces of slate on the four crossbeams.
2.2 Ensure that the slate is square to the frame. Secure the slate to the cross beams. (Pre-drill with 3/16” drill
bit)
2.3 Finalize the slate leveling process using flat shims and/or wedges. Fill the seams and screw holes and
install the bed cloth.

2
STEP 3 ATTACH THE CUSHION RAILS
The picture frame rail assembly is fully assembled upside down on a clean level surface.
3.1 Unpack the cushion rails & apply the cloth. (It is recommended that the cloth be installed in a shop
environment prior to installing the table in the customer’s home or business).
3.2 Lay out the rails upside down & build picture frame assemblies utilizing the 5/16”x 6 3/4” bolts,
washers, and nuts, for the side pocket assembly and 5/16”x 3 1/2" bolts, half-moon washers, and nuts
for corner pockets.
3.3 Loosely attach aprons to rails using small “L” brackets, 1/4" x 1/2" bolts and washers. Loosely attach
blind block to blinds using 1/4” x 5/8” bolt and washer.
3.4 Loosely attach corners to aprons using 5/16” x 1 1/4" black bolts, washers, and nuts. Align aprons to top
rail.
3.5 Tighten all bolts and place on slate. Check for alignment and adjust as necessary.
3.6 Attach rails to slate using 5/16” –18 x 2” rail bolts and 3/8” dome tooth washer. Hand tighten the
cushion rails. NO IMPACT TOOLS PLEASE!
STEP 4 INSTALL THE POCKETS
4.1 Install the pockets (pre drill approx. ¼” from top of pocket) before securing in place with round heads
brads. (2 per pocket)
Should there be any problems please contact us at:
Presidential Billiards, L.P. Tel: [phone]
20221 Caroline Way 866-728-2253
New Caney, TX 77357 Revised: 2-21-2019

3
Ford Installation Hardware
Step 1
1.3
16
3/8”–16 x 5” Bolt
BHH3816127GA ZN
16
#10 –14 x 30mm Barrel Nut
NV0014.12.11
24
3/8" x 1 1/4" Washer
WF38125 ZN
8
5/16”–18 x 3 1/2” Bolt
BHH561889GA ZN
12
5/16” x 7/8” Washer
W56USSHT ZN
12
5/16” – 18 x 1 3/4" Bolt
BHH561838GA ZN
1.4
8
3/8”–16 x 5” Bolt
BHH3816127GA ZN
16
3/8" x 1 1/4" Washer
WF38125 ZN
8
3/8” – 16 Nut
HN3816 ZN
1.5
16
5/16”–18 x 3 1/2” Bolt
BHH561889GA ZN
16
5/16” x 7/8” Washer
W56USSHT ZN
Step 2
2.2
17
#14 –10 x 2 1/2" Screw
NU3940.10.11
Step 3
3.2
4
5/16” - 18 x 3 1/2” Bolt
BHH561889GA ZN
8
Half Moon Washers
NE1965.12.60
4
5/16”- 18 Nut
HN5618 ZN
2
5/16” - 18 x 6 3/4” Bolt
NU4921.11.11
4
5/16” x 7/8”Washer
W56USSHT ZN
4
5/16”- 18 Nut
HN5618 ZN
3.3
14
“L” Bracket for Blinds
NE4646.10.10
28
1/4”-20 x 1/2” Bolt
BRH142013CRII ZN
28
5/16” x 7/8” Washer
W56USSHT ZN
8
1/4” – 20 x 5/8” Bolt
NU1847.10.11
8
5/16” x 7/8”Washer
W56USSHT ZN
3.4
16
5/16”–18 x 1 1/4" Black Bolt
NU3961.13.11
16
5/16” x 7/8”Washer
W56USSHT ZN
16
5/16” - 18 Nut
HN5618 ZN
18
5/16”–18 x 2” Bolt
BHH561851GA ZN
18
3/8” Dome Rail Washer
NE3527.10.10
Step 5
4.1
14
3/4" Round Head Nails
TACKS