Pressol 13003 User manual

GInstallation and operating instructions
IMPORTANT: READ BEFORE USING
1. Technical data
PP (polypropylene) PUMP PPS (polyphenylene sulde) PUMP
Pump Type Lever Action Lever Action
Pump Body #1 Color Blue Black
Max. Flow 10 oz / Stroke 10 oz / Stroke
Max. Fluid Temperature 140° F 160° C 140° F 160° C
Bung Adapter 1-½“ & 2“ 1-½“ & 2“
Wetted Materials PP, Steel, Polyethylene (PE) PPS, SS304, SS316, PTFE, PVDF
Max. Viscosity 1,000 SSU 1,000 SSU
Application Diesel, Kerosene, Lubricant Gasoline, Diesel, Kerosene, Lubricant, Water,
Alcohol, Acids, Alkali, Solvents, Chemicals
2. Assembly and Installation
Check to see if all parts are included.
Install pump handle (Ref No. 8) to piston rod (Ref No. 9) with two sets of screws and nuts (Ref No. 7).
Install discharge spout (Ref No. 3) and screw the nut (Ref No. 2) tightly to the outlet thread of pump body
(Ref No. 1) and make sure discharge spout is secured.
Screw the assembled suction tube (Ref No. 17, 18 & 20) to inlet of pump body.
Insert this pump into the opening of drum. Then screw the bung adapter clockwise into drum.
The pump is now ready for operation. Liquid should begin to ow after several strokes. If any leakage
occurs, tighten piston rod nut (Ref No. 4) on top of pump carefully. Over tightening this nut will damage
seal, make the pump dicult to operate, and may strip nut.

GInstallation and operating instructions
Parts List
Ref No. Description Ref No. Description
1 Pump Body 12 Rod Plate
2 Coupling Nut 13 Valve Nut
3 Spout 14 Foot Valve Seal
4 Piston Rod Nut 15 Base Plate
5 Piston Rod Seal 16 Base
6 Handle Lever 17 Tube
7 Nut & Screw 18 Telescopic Tube
8 Handle 19 Tube Seal
9 Piston Rod 20 Tail Telescopic Tube
10 Valve Plate 21 O-ring
11 Valve Base 22 Valve
3. General Safety Information
Always carefully read, thoroughly understand and follow the pump operating instructions. Inspect your
pump thoroughly to verify its proper assembly and then use this pump correctly with cara for tha purpose.
Failure to do may cause damage or personal injury, and will invalidate the warranty. Retain instructions for
future reference.
Prior to use, always carefully and thoroughly read and understand the OSHA information contained in the
Safety Data Sheet supplied for the chemical which is to be pumped. Contact your uid supplier to check
for compatibility with pump prior to installation and operation.
Pump should be washed out befor it is used since processing lubricants may contaminate the uids.
Wear protective clothing (goggles, face masks, long sleeves, long pants, gloves, aprons, etc.) as set forth in
the OSHA Safety Data Sheet when pumping any hazardous chemicals.
When pumping ammable liquids, pump containers should be grounded to avoid static electricity and
pump must be stored in a ventilated area after use.
To stop siphoning, rotate handle 1/4 turn (leave handle in horizontal position).
After using pump, position handle straight down, liquid will drain back to container.
If pump is removed from drum, rinse it thoroughly in a liquid that is compatible with both the pump and
the uid being pumped.
Regularly check pump and suction tubes for leaks. Leaks in the suction line or in pump housing will cause
inecient pumping and loss of prime.
Pressol Schmiergeräte GmbH
Parkstraße 7
93167 Falkenstein | Germany
Tel. [phone]
Fax [phone]
[e-mail]
www.pressol.com