Prestel KB-IPM User manual
PART ONE: KNOWING THE KEYBOARD
Keyboard function on the front panel：
Keys
Function description
0~9
Value of number
MON
To call monitor
WIN
To call window (screen)
CAM
To call Camera
CLEAR
Clear/log out input number, to cancel operation
MENU
menu
ENTER
to confirm input, enter sub menu, when input IP address, key of“.”
Shuttle
Control cursor movement
Joystick
To control PTZ movement, menu cursor movement.
Joystick zoom
Zoom near or Far
NEAR
Zoom near
FAR
Zoom far
OPEN
Iris open
CLOSE
Iris close
SHOT
Auxiliary keys
RUN
Run
STOP
stop
MULT
Multiplexer
PRESET
Preset
Power indicator
Blue indicator always be on
Communication
indicator
Green indicator twinkle.
AUX1
WIN forward switch
AUX2
Auto Switch stop
AUX3
Auto Switch start
AUX4
WIN back switch
PART THREE: CONFIGURATION
1.Check the IP Address of each component
1) Open IPConfig.exe
2)On the tab of “Net”, click “Search” you will find the IP Address of the keyboard
On the tab of “ONVIF”, click “Search” you will find the IP Address of the camera.
You are supposed to ensure that all necessary equipment has been connected correctly by
checking whether the information of the all units are showing on the IPConfig.exe
Keyboard
Camera
Model
IP Address
▲Notice 1: Please ensure that the IP Address of each unit is on the same gateway, or it won’t show
up in the IPConfig.exe. For example, If the IP Address of the computer is 192.168.6.50, all equipment
IP Address should be 192.168.6.n.
2. Configuring on the configuration interface
2.1 Configuring on Keyboard
When the connection is completed, the interface of the keyboard will show as below
Default User Name:1000
Default Password: 12345
1)After logging in to the keyboard, you are supposed to long press the “MENU” button
on the panel and you will see the interface as below.
In the interface of “Network”, you will
see the IP Address of the keyboard. You
could change the IP Address of the
keyboard on the interface or the web
page of configuration
Operation description:
▲Notice: The Video shown on the keyboard is the same as the image from the Monitor 1
Functions
Operation desc.
MON splitting
N（MON No.）+MON+M（1/4/9/16）+MULT
WIN switch video
N（WIN No.）+WIN+M（CAM No.）+CAM
To run auto switch
N（WIN No.）+WIN+M(Salvo No.)+AUX3
To stop auto switch
N（WIN No.）+WIN+M(Salvo No.)+AUX2
To set Preset N
N+（SHOT+PRESET）
To call Preset N
N+PRESET
PTZ control
To control current CAM/PTZ by joystick
MENU
To press MENU button a little long time, to enter
system setup, to press MENJU button a little short
time, to check Source list.
Note: auto switch including cruise, salvo, splitting.
After setting, it will show the interface as below. Then click “save”, or the settings will be
invalid.
▲Notice:The operation will be valid only if “save” is clicked.
2)Switch from “Monitor” to “Window” , you will see nothing but blue screen both on
configuration interface and monitor.
3)Click “Win=Mon”, the monitor and interface will display as below.
3) You will see that all added cameras are under “Unidentified” state, then click “All
Identify” to activate the cameras.
▲Notice:If there is some cameras that could not be identified, please check the ID Name and the ID
Password of the cameras again.
Then the ID state of all cameras are succeed as below.(Don’t forget to click the button “save”)
2.2.4 Realize some functions
Choose the “Switch” Tab, you will see there are 3 functions as below.
1)Cruise
You could assign any window( WIN N) to display indicated cameras automatically
followed by recycling in indicated time.
EXAMPLE1:
Under the help of the keyboard, you could indicate any “WIN”to show the video of camera 2,3,4
automatically followed by recycling in 15 seconds.
2)Salvo
The function is similar to the Cruise but it could make numbers of windows to realize it.
EXAMPLE2:
Under the help of the keyboard, you could make
①“WIN1”to display camera1,2,3 automatically followed by recycling in 15 seconds.
②“WIN2”to display camera1,2,3 automatically followed by recycling in 15 seconds.
③“WIN3”to display camera1,2,3 automatically followed by recycling in 15 seconds.
3)Segmentation
You could assign one monitor to divide into 4/9/16 windows and each window displays a
certain video of camera automatically followed by recycling in certain time.
EXAMPLE3:
In Segmentation section, you could choose the “splitting number”to “4”,“Mon No”is “1”.
Under the help of the keyboard, the matrix will realize the function as below
①In first 15 seconds, Mon 1 will split into 4 images and each window will show the video of the
camera 1,2,3,4
②In next 15 seconds, Mon 1 will split into 4 images and each window will show the video of the
camera 5,6,7,8
③In last 15 seconds, Mon 1 will split into 4 images and each window will show the video of the
camera 9,10,11,12
Table of contents
Other Prestel Keyboard manuals
