PrimaLuceLab EAGLE4 User manual

VERSION 1.0
Update 15-12-2020
EAGLE is manufactured by PrimaLuceLab S.p.A. (Italy). For any matters relating to the use, service and warranty, please
refer to the addresses given in the relevant documents.
PrimaLuceLab S.p.A. • Via Roveredo 20/B, 33170, Pordenone • www.primalucelab.com
EAGLE4
advanced control unit for telescopes and astrophotography

PrimaLuceLab S.p.A. EAGLE4 User Manual
English
CAUTION: To avoid danger of electric shock and malfunction, do not expose EAGLE to rain or moisture. The electronics are
not waterproof so in adverse weather like rain or snow, the EAGLE is not to be used outdoors.
PLEASE NOTE: EAGLE is designed to control telescopes and accessories for astronomy and is not a standard computer.
Please do not modify EAGLE system settings since this could stop some of the EAGLE features. Additionally, operating
system updates are not required if your EAGLE does not connect to the internet.
FIRST CONNECTION: For wireless connectivity, EAGLE creates a WiFi network at the same frequency as those of usually
modems / routers used to connect to the internet. So if you use EAGLE at home (for example the first time, to install your
software) you might notice a low signal or, in some cases, have connection problems. You can move it to an area with
fewer WiFi connections or connect it to a monitor (HDMI), keyboard (USB) and mouse (USB) to install your software.
WINDOWS: EAGLE includes a computer with Windows OS. For any reference on how to use Windows, please refer to the
operating system user manual.
QUALITY CONTROL: After assembly in our laboratories, every EAGLE unit, is tested by PrimaLuceLab technical experts to
verify the correct operation of all components = the integrated computer, stability and speed of the wireless connection
and the power bridge.
pagina 1
CAUTION: in order to connect EAGLE to other mechanical PLUS elements please avoid to use too
long screws that may touch the internal electronics of the EAGLE. THE THREADED PART OF THE
SCREW THAT EXIT FROM THE ELEMENT (ring, bar or clamp) TO BE CONNECTED TO THE EAGLE HAS
TO BE NO LONGER THAN 6mm. If any of the screws touches the internal elements of EAGLE, this
could lead to breakage or malfunction.
CAUTION: EAGLE must be powered with 12V regulated voltage. You can use a power supply with 12V output voltage or a field
battery. If you use a battery, this MUST be provided with a proper voltage stabilization. In case of any malfunction, immediately
unplug the power supply. DO NOT CONNECT TO THE EAGLE A BATTERY WITHOUT 12V VOLTAGE REGULATOR since it may da-
mage the other instruments powered by EAGLE (like the cooled camera). Immediately disconnect power supplies or battery if
there’s any malfunction of the unit.
CAUTION: Before installing your devices driver and your astronomy software in the Windows operating
system of the EAGLE, PLEASE CREATE A BACKUP COPY OF YOUR SSD DISK by following the instruc-
tions you find at paragraph “First use: backup your SSD drive before installing your software” of this
user manual.

PrimaLuceLab S.p.A. EAGLE4 User Manual
Index
Components Identification 4
First use: how to choose the correct power source 5
First use: switch on and activation of wireless network 6
First use: Setting remote control with iPhone or iPad 10
First use: Setting remote control from a Windows computer 14
First use: Setting remote control from a Mac computer 16
First use: Setting remote control from an Android device 20
First use: backup your SSD drive before installing your software 24
First use: install your software 29
First use: turn off EAGLE 30
First use: installing EAGLE on the telescope 31
First use: powering other instruments connected to the EAGLE 34
First use: remotely control devices with EAGLE Manager 36
- connect or disconnect every power out port of EAGLE 38
- set power out voltage of the 3 power out ports with adjustable voltage 39
- connect or disconnect devices attached to the 4 USB 2.0 ports 40
- check for power in voltage and battery lifetime 40
- set WiFi connectivity 41
-remotely turn on/off the entire telescope 43
- change the password of the WiFi network created by EAGLE 44
- Check for GPS data 45
- EYE sensor data 47
- DARK mode 48
Advanced use: EAGLE ASCOM drivers 49
Advanced use: program connection and power to devices 50
page 2

PrimaLuceLab S.p.A. EAGLE4 User Manual
WARNING
If improperly handled, EAGLE may be damaged, so please follow the instructions below:
•Do not disassemble
•Do not open, damage or subject to electric shock or excessive impact any part of EAGLE. Do not drop.
•Do not short the electronic elements
•Do not expose at temperatures above 50°C
•Do not burn or incinerate any component.
•Do not wet any electronic or electric component
•Do not bend, modify or force any part of EAGLE
•Never point the EYE sensor without cap towards the Sun. If you use your telescope to observe or photograph the Sun,
please cover the EYE sensor with the proper cap provided in the box before pointing the Sun.
NOTICE In case you check any malfunction, please contact us immediately (+ 39-0434-1696106 or support@primalu-
celab.com). Do not try to disassemble, repair or modify yourself EAGLE, without our written approval, in order not to
loose the manufacturer warrantee.
Advanced use: remotely turn on EAGLE with wired connection 51
Advanced use: configure EAGLE to automatically start when power is restored 55
Controlling the telescope remotely with Cartes du Ciel 57
Autoguiding with PHD2 Guiding 64
Drift Alignment using PHD Guiding 69
Q & A 77
Add EAGLE’s ports control in external software 79
Troubleshooting 82
page 3

PrimaLuceLab S.p.A. EAGLE4 User Manual
Components Identification
The numbers indicate the name of the specific component. Read the paragraphs below for detailed operation description.
page 4
Power IN 12V
HDMI port for external monitor
3
4
n.2 USB 3.0 ports
5
n.2 USB 3.0 ports
7
On / Off switch
8
n.4 12V power OUT
2
Network port
n.4 USB 2.0 ports
WiFi Antenna
1
6
n.3 power out ports with regulated voltage
9
10
EYE light sensor
11
Status LEDs
GPS Antenna
12
13