Primo International EZ Base RTA User manual

EZ Base RTA Assembly
Instructions
**Actual product may differ slightly from illustration
Scan QR code for video of the assembly

We would like to thank you for your purchase.
Now that your new product has been delivered, let us help you
through its assembly so you can enjoy it fully.
STEP 1
Open the box at the end with
the handle.

STEP 2
STEP 3
Remove all pieces from the packaging and make sure there is
nothing left inside the carton before disposing of it. Please pay
attention to any small hardware that could have come loose.

STEP 4
Remove the components from the protective material and
place them on a clean, flat and levelled surface, this is
important. The
box should
contain the
following
pieces:
2x Side frames (A)
(each split in 2)
2x End frames (B)
1x Cover (E)
1x Hardware (F) pack
Slats (D)
Important:
Depending on the size of the platform base you purchased, your
carton will contain:
Twin & Full: No center rail (C)
Queen: 1x Center rail (C)
King : 2x Center rail (C)
The center rail is made of 2 pieces joined together. See
instructions In following pages.
A
A
B
B
C
D
E
F

This product comes with removable
Frame covers which are to be fitted
Once the rails are set up
STEP 5
Hardware contents (F):
4xLegs (H)
4xCorner
brackets (I)
2xHeadboard
bracket (K)
2xCenter rail
bracket (L)
3xSupport leg
(J)
H
I
J
K
L
2
x Side rail connecting plate (W
)

Carriage bolts (O)
Flat washers (P)
Nuts (Q)
Wood screws (R)
Spanner (S)
Allen key (T)
Bolt (M)
Washer (N)
M
N
O
P
Q
R
S
T

STEP 6
IMPORTANT NOTE
The corner brackets are fitted with round holes and rectangular holes.
The round holes must be attached to the bracket to the side of frames
(A)
The rectangular holes must be attached to the bracket to
the End frames (B)

STEP 7
FOR QUEEN AND KING SIZES ONLY
Use bolt (M) and washer (N) to attach to the center rail bracket (L) and
end frames. Attach bracket upward as illustrated below. Attach
bracket so it is levelled to the top and tighten using the Allen key (T)
Attach the 4 corner brackets (I) to the 2 end frames (B) with the
bolts (M) and washers (N) using the rectangular holes. Do not fully
tighten the bolts at this stage, leave them loose.

STEP 8

Align the 2 frames forming one
side rail. Make sure the holes
correspond to the holes on
connector plate W

Put the 2 frames on their side
showing the 2 attachment
holes on the underside of the
frames Attach the connector
plate to the side rails leaving
the bolt loose.
Tips: placing the 2 rails
slightly in an angle facilitate
this step

Cover the rails with the
covers provided.
Adjust the cover over the
frame and attach to the
velcro on top and bottom
of each frame.

STEP 9
Attach the side frame (A)
to the end frame (B)
using bolts (M) and
washers (N)
Leave the bolt loose,
do not tighten at this
stage of assembly
B
A
M
N

STEP 10
Attach all frames together but leave bolts loose
STEP 11
Adjust each corner so the end of the frame (A) correctly lines
up with end frame (B) Now, tighten all the bolts.
B
A

STEP 12
Put the frame on its side
and attach legs (H) to the
corner brackets base
NOTE:
Once all 4 legs are
attached, please re-check
that all bolts are tightened.
H

STEP 13
Attach the support leg (J) to the center rail (C) using the bolts (M)
and washers (N).
IMPORTANT, the bolts must be attached from the opposite side of
where the attachment nut is flush against the rail.
See illustration below
C
QUEEN AND KING SIZES ONLY

STEP 14
Once the support legs are attached , place the center rail in the
center rail brackets.
This is the wrong
side.
Thi
s is the correct
side.
FOR QUEEN AND KING SIZES ONLY

STEP 15