Primo International EZ Base User manual

EZBaseAssembly
Instructions

STEP1
Openthepackagingattheend
wherethehandleisandidentify
thelocationoftheupholstered
framesinsidethepackaging.
WeatPrimoInternationalwouldliketothankyouforyour
purchase.
Nowthatyournewproducthasbeendeliveredto
you,letushelpyouthroughitsassemblysoyoucanenjoyitfully.

STEP2
Openthepackagingaftermakingsuretheupholstered
framesinsidetheboxareontheoppositesidetoavoiddamaging
thematerial.
STEP3
Removeallpiecesfromthepackagingandmakesurethereis
nothingleftinsidethecartonbeforedisposingofit.Pleasepay
attentiontoanysmallhardwarethatcouldhavecomeloose.

STEP4
Removethecomponentsfromtheprotectivematerialandplace
themonaclean,flatandlevelledsurface,thisisimportant.
Theboxshouldcontainthefollowingpieces:
2xSideframes(A)
2xEndframes(B)
1xCenterrail(C)
10xSlats(D)
1xCover(E)
1xHardware(F)
pack
AA
BB
C
D
E
F
STEP5
IdentifythecontentoftheHardwarepack(F):
4xLegs(H)
4xCornerbrackets(I)
1xSupportleg(J)
2xHeadboard
bracket(K)
2xCenterrail
Bracket(L)
H I
J
KL

26xBolts(M)
26xWashers(N)
4xCarriagebolts(O)
4xFlatwashers(P)
4xNuts(Q)
4xWoodscrews(R)
1xSpanner(S)
1xAllenkey(T)
M
N
O
P
Q
RS T
IMPORTANTNOTE
Donotuseapowertooltoassemblethisproductasitcould
damagethethreadofthehardwareandaffectthesolidity/durability
oftheproduct.

STEP6
Nowthatyouhaveidentifiedallcomponents,wecanstartthe
assemblyprocessbutfirst,paycloseattentiontothefollowing
detail:
IMPORTANTNOTE
Thecornerbracketsarefittedwithroundholesandroundedrectangle
holes.TheroundholesmustbeusedtoattachthebrackettotheSide
Frames(A)andtheroundedrectangleholesusedtoattachthebracket
totheEndframes(B)
Roundhole
Roundedrectangle
hole

STEP7
Usethebolt(M)andwasher(N)toattachthe2centerrailbracket(L)to
theendframes(B).Thebracketmustbeinstalledupwardasillustrated
below.Adjustthebracketstobestraightandlevelagainstthetopofthe
frameandtightenusingtheAllenkey(T)
M
NLT
B
B

STEP8
Attachthe4cornerbrackets(I)tothe2endframes(B)withthe
bolts(M)andwashers(N)usingtherounded
rectangleholes. Donotfullytighten theboltsatthisstage,leave
themloose.
I
I
Rounded
rectangle
hole
Thebottomofthecorner
bracketisfittedwithaplate
wherethelegswillattachon.
Insuretopositionthebracket
sotheplateisatthesame
leveltothebottomofthe
frame.
B
B

STEP9
Attachthesideframe(A)
totheendframe(B)using
bolts(M)andwashers(N)
Leavetheboltloose,
donottightenatthis
stageoftheassembly

STEP10
Completeattachingallframesbutleaveallboltsloose
STEP11
Adjusteachcornersotheendonthesideframe(A)correctlylines
upwithendofendframe(B)thenthightenthebolts.

STEP12
Puttheframeonitsside
andattachthelegs(H)to
thecornerbracketsbase
H
Onceall4legshavebeenattached,pleasere‐checkthatallboltsare
evenlytighten.

STEP13
Takethecenterrail(C)andthesupportleg(J).
Locatetheattachmentscrewsonthecenterrail
H
Attachthesupportleg(J)tothecenterrail(C)usingthebolts(M)
andwashers(N).VERYIMPORTANT,theboltsmustbeattachedfrom
theoppositesideofwheretheattachmentnutisflushagainsttherail.
Thisisthewrongside.
Correctsidetoattachthe
supportleg

STEP14
Oncethesupportlegisattachedto
thecenterrail,placethecenterrail
inthecenterrailbrackets.

STEP15
2ofthewoodenslats(D)are
fittedwithholeswhichwillbe
usedtoattachthemtotheside
frames.Those2slatsaretobe
placedinthecenterofthebase
asillustratedbelow.

Yournewplatformbasecannowbecovered.
UseaPhillips(starhead)
screwdrivertoattachthe2
middleslatstothesideframes
usingthewoodscrews(R)

LASTSTEP
Usethecover(E)torecovertheframeandvoila,yournew
platformbaseisreadyforuse.

OPTIONALSTEPSFORHEADBOARD
Shouldyoudecidetouseyournewplatformbasewithaheadboard,
therequiredhardwareisalreadyprovidedwiththepackyoureceived.
1st STEP:
Taketheheadboardbracket(K)providedwiththehardwarepack
ofyourbaseandidentifywhichholesonthebracketcorresponds
totheattachmentholesonyourheadboard.
2nd STEP:
Onceyouhaveidentifiedthematchingholes,put1carriagebolt (O)
ineachmatchinghole(Intheillustrationbelow,thewasher(P)and
nut(N)areusedtokeepthecarriageboltsinplaceonly)

3rd STEP:
Attachtheheadboardbracket(K)totheendframe(B)thatisalready
fittedwithpre‐drilledholesusingthebolts(M)andwashers(N).
Adjusttheheightofthebraketbyslidingitupordown.Onceatthe
desiredheight,makesurethebracketisstraightandtightenthebolts.

4th STEP:
Youcanslidethecarriagebolts
side‐to‐sidetofitintothehead‐
boardattachmentholesafter
removingthenutandwasher.
Oncetheheadboard(not
Illustrated)isinplace,usethe
spanner(S) totightenittothe
headboardbracketsusingthe
Washers(P)andnuts(Q).
S