Primus 28900 User manual

Save This Manual for Future Reference
Original Instruction
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING
MACHINE
Log Conveyor
Operator’s Manual
MODEL NUMBER :
SERIAL NUMBER : 28900
Both model number and serial number may be found on the main label.
You should record both of them in a safe place for future use.

B
o
x
(
O
p
t
i
o
n
a
l
P
l
o
w
B
l
a
d
e
)
ASSEMBLY
Following the assembly directions below, you will
assemble the snow thrower in a few minutes.
Note: The hardware has been put at its right
position loosely.
M8 45 2
CONTENTS SUPPLIED
The log conveyor comes partially assembled and
is shipped in carefully packed carton. Note: After
all the parts have been removed from the carton,
you should have:
3 4 5 6 7
2
8 9 10
1
11 12 13
14 15
1. Wheel Shaft
2. Belt
3. Support Leg A
4. Support Leg B
5. Tilted Support Leg 1
6. Tilted Support Leg 2
7. Reducer
8. Adjusted Screw Rod
9. Wheel Support
10. Wheels
11. Lower Support Plate
12. Middle Support Plate
13. Upper Support Plate
14. Operator’s Manual
a
M8 30 6
M10 35 6
M10 40 4
M10 50 2
M12 3
M8 45 2
a
M8 30 6
M10 35 6
M10 40 4
M10 50 2
M12 3
b
M6 16 4
15. Hardware Bag,
including
Line up the holes in the lower and middle support
plates on the back side. Insert M10x35 bolts and
washers from one side, and tighten down with
washers and nuts from the other side.
1.
CONTENTS SUPPLIED

b
M6 16 4
Line up the holes in the upper and middle
support plates on the back side. Secure the
middle holes with M10x35 bolt and washer from
one side and washer and nut from the other
side. Fix the support leg A simultaneity when
secure the holes on both edge by insert the
M10x35 bolts and washers from one side, and
slide the support legs A on the bolts from the
other side, tighten down with washers and nuts.
It is the same way to fix support leg B with the
lower and middle support plates.
Insert the support legs A into the sleeves which
are mounted on the tilted support legs 1 with
M10x40 bolts and nuts. Screw off the nuts and
washers, then slide the support legs 2 on the
bolts, tighten down with washers and nuts
previously screwed off.
Insert the support legs B into the sleeves which
are mounted on the tilted support legs 2 with
M10x40 bolts, washers and nuts.
Align up holes in the wheel support leg and the
lower support plates, and then secure them
with six M8x30 bolts from outside, washes and
nuts from inner side.
Align up holes in the wheel support leg and the
wheel shaft, and then insert the M8x45 bolts
with washers from the bottom, tighten down
the nuts from the other side.
Mount the reducer bracket on the lower support
plates with three M12 bolts.
2.
3.
4.
5.
6.
7.
Secure the wheels on the wheel shaft with the
wheel caps.
Wrap the belt on the driving and driven belt
pulleys over the machine, and link it up with
buckle.
1.
2.
After you finished the assembly, please adjust the
machine as follows.
You should fix the adjusted screw rod firstly;
adjust this screw rod until the belt not slippery.
Loose the three M12 nuts under the reducer
bracket and the two M10 nuts at the other side
of the bracket wall, then adjust the two M10x50
bolts until the driving and driven belt pulley
parallelized and the belt run on its way then
tighten down the M12 and M10 nuts.
1.
2.
Adjusting
M10X50 Bolt
M10 Nut
M12 Nut
Adjusted
Screw Rod
Fix the switch bracket on the middle support
plates with four M6x16 bolts, followed by
washers and nuts.
3.

The rating plate on your machine may show
symbols. These represent important information
about the product or instructions on its use.
SYMBOLS
Read these instructions in full
before using the machine.
Keep your work space tidy!
Untidiness may result in accidents.
Wear eye protection.
Wear hearing protection.
Keep bystanders away from the
working area.
Keep clear of moving parts.
ENVIRONMENTAL
ENVIRONMENTAL
Recycle unwanted materials instead
of disposing of them as waste. All
tools, hoses and packaging should
be resorted, taken to the local
recycling center and disposed of in
an environmentally safe way.
Before starting any repair
maintenance or cleaning, always
disconnect the power.