Pro-Elec PEL00924 User manual
1
Model: PEL00924
Wall Mounted Hair Dryer
2
When using electrical appliances, basic safety precautions should always
be followed to reduce the risk of re, electric shock and injury to persons or
property.
Read all instructions before using the appliance and retain for future reference.
• Check that the voltage indicated on the rating plate corresponds with that of the
local network before connecting the appliance to the mains power supply.
• Before drilling any xing holes, check that there are no hidden obstructions behind
the mounting surface, such as pipes or cables.
• Ensure the wall xing can support the weight of the device and that the wall xings
will be securely anchored into solid masonry.
• The hair dryer can be mounted on normally ammable surfaces.
• This appliance is designed for indoor use only.
• There are no user-serviceable parts in this product. Refer servicing to qualied
personnel.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not operate this appliance with a missing casing or a malfunction or after being
damaged in any way.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
• Do not block the air inlet or outlet as this will cause the dryer to overheat.
WARNING: Do not use this appliance near bathtubs, showers, basins or other vessels
containing water.
IMPORTANT SAFETY INFORMATION
WHAT’S INCLUDED
• Hair Dryer
• Installation / operation manual
• Wall Plugs and mounting screws
PRODUCT OVERVIEW
• Wall mounting
• 15 minute timer
• Shaver socket with waterproof cover
• Variable temperature
3
INSTALLATION
• The dryer should be mounted between 1.4m for a child to 1.7m for an adult from
the oor measured to the bottom of the casing.
• Drill two holes 6mm dia into the wall at 217mm centres vertically (see template
supplied).
• Fit the wall plugs and attach the upper hanger using the screw provided.
• Remove the retaining screw and open the dryer bottom access cover below the
shaver socket.
• Suspend the dryer from the hanger and x into place by inserting the lower screw
through the bottom mounting hole and screw into the lower wall plug.
• If you have an existing wiring and do not need the mains wire already tted to the
dryer, there is an additional rear cable entry point on the rear cover.
• The wiring terminals are also accessible through the bottom access cover.
• Switch off the mains supply before connecting the wiring as follows:-
Live - Brown or red
Neutral - Blue or black
• If you are connecting to a fused spur, a 13A fuse should be used.
• Restore the power supply once the installation is complete.
WARNING: It is not recommended to attempt to remove the air pipe as there is a risk of
damaging the appliance.
• In order to remove the air pipe insert a narrow at blade screwdriver into the slot in
the connector and depress the tab and then rotate the pipe to the left by 15 degrees
then gently pull the pipe clear.
• To ret the pipe engage the connector into the receptacle, push fully home and
rotate to the right until the tabs engage.
10
8
4
SPECIFICATIONS
CLEANING AND MAINTENANCE
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling of
the materials used. Contact your local authority for details of recycling schemes in your
area. Made in China. PR2 9PP
Man Rev 1.0
Voltage: 220-240V~50Hz
Rated Power: 1000W
Current: 4.3A
Air Volume: 77m3/hour
Air Velocity (max): 15m/s
IP Rating: IP24
Class: Class II Double Insulated
• Disconnect the mains supply from the appliance and wait for it to cool completely
before cleaning.
• Clean with a soft damp cloth.
• Do not use any chemicals, abrasives or solvents that could damage the appliance.
OPERATION
• After nishing the installation, and switching on the power, remove the hose nozzle
from it’s stored position and the dryer will power on.
• Adjust the heat and ow by turning the main rotary control in the centre of the front
panel.
• To power an electric shaver slide up the protective door and insert the shaver mains
plug into the relevant socket depending on type and voltage requirement.
Table of contents
