PRO SIGNAL PSG3026 User manual

1
PSG3026
4K HDMI AUDIO EXTRACTOR

2
WHAT’s IN THE BOX
OVERVIEW
IMPORTANT SAFETY INFORMATION
INSTALLATION
• The PSG3026 enables you to extract 4K HDMI for both digital optical S/PDIF (Toslink)
and stereo analogue audio signal for use by an amplier or AV receiver
• Upscale 1080p signal to 4K or downscale 4K signal to 1080p modes available.
• Full OSD operation by using a 5 way joystick control for easy set up.
• Main unit.
• 5V DC Power Supply
• User’s Manual
• Attachment screws/wall plugs
• DB9(F) to 3.5mm stereo jack lead
Please read these instructions carefully before use and retain for future reference.
• Check that the voltage indicated on the PSU rating plate corresponds with that of the
local network before connecting to the mains power supply.
• Please make sure all devices you wish to connect have been powered off.
• Connect the source device to this product using a suitable cable.
• Connect the output(s) to the required devices (see diagram below).
• Insert the 5V DC connector from the power supply into this product and then connect
the power supply into the wall mains outlet. The green LED will illuminate.
• Power on the source and destination device and select the relevant input if required.
DB9(F) to 3.5mm stereo jack lead pin connections

3
OPERATION
Joystick 5 way control
Menu options
UP
DOWN
LEFT RIGHTENTER
• After making your selection press the button to conrm before moving on to the next
option.
• The blue LED will illuminate when HDMI output 1 is selected.
• The red LED will illuminate when HDMI output 2 is selected.
RS232 3.5mm JACK
Pin Function Pin Function
2TX TIP RX
3RX RING TX
5GND STEM GND
• CEC function only works using output 1.
• Any HDMI output device not compatible with HDCP2.2 will cause HDMI video output,
to fail. Under HDCP 2.2 mode if any monitor HDCP authorization fails, this will cause
no video output to all connected monitors.
• Up/down scale modes only support resolution conversion, frequency will not change.
• Under HDMI 2.0 mode, it is recommended to use a premium certied HDMI cable.
Main Menu Sub Menu Function
Output 1 mode
Normal Output video same as input Video
Upscale 1080P Upscale to 4K
Exit Exit sub menu option
Output 1 Subsampling Normal Output colour subsampling same as Input
4:2:0 to 4:4:4 4K6G 4:4:4/4:2:2 convert to 4K3G 4:2:0
Exit Exit sub menu option
Output 1 Audio Mode
Normal Audio output
Mute No audio output
Exit Exit sub menu option
Output 2 Mode
Audio Only Audio output only - no video
Downscale 4K scaled to 1080p
Splitter Distribution mode - output 2 same as 1
Exit Exit sub menu option
EDID (video)
Auto
Use OUTPUT 1 EDID as priority, if
OUTPUT 1 and OUTPUT 2 are not
connected with a TV, default set as 4K
Output 1 Use output 1 EDID
Output 2 Use output 2 EDID

4
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in Taiwan. PR2 9PP
Man Rev 1.0
SPECIFICATIONS
Operating environment 10-45o Storage-30-70o, Humidity up to 95%
Power supply 220-240V~50Hz
Power requirement 5V DC 1A
Power consumption (max) 4W
HDMI input/output HDMI 2.0, HDCP 2.2/1.4 compliant
Audio support
LPCM 7.1@192KHz up to 7.1 channel. Routes HDMI
audio simultaneously via S/PDIF and 3.5mm stereo
audio outputs
Support
1080p@60Hz 16bit, 3D, HDR, 4K@60Hz
4:4:4/4:2:2 18Gbps (6Gbps per colour) convert to 4K
3G 4:2:0
Scaling
Support 1080p to 4K upscale and 4K to 1080p
downscale. Support extracts the 4K HDMI audio
and output to a multi-channel digital or analogue
audio signal.
Connections
Input: HDMI x 1, Output: HDMI x 2, Optical out x 1,
analogue stereo out x 1.
Support CEC pass-through
Main Menu Sub Menu Function
Preset 4K Default 4K 60Hz 8bit
Exit Exit sub menu option
EDID (audio) Auto
Use OUTPUT 2 as priority, if OUTPUT 1
and OUTPUT 2 are not connected with a
TV, default set as LPCM 2.0
Output 1 Use output 1 EDID
Output 2 Use output 2 EDID
5.1 audio Default LPCM 5.1
2.0 audio Default LPCM 2.0
Exit Exit sub menu option
Misc Main MCU: XXX Firmware version check
Exit Exit menu function