Pro-Team ProGen 1073300 User manual

Upright
Service Manual
ProGen Models
1073300 & 1073290

Table of Contents
Base Cover.............................................................................................. 1
Clutch, LED Front Light, Belts, and Control Boards.............................. 2-3
Filter Bag Housing .................................................................................. 4
Foot Pedal .............................................................................................. 5
Motor.................................................................................................. 5-7
Power Head Hose ................................................................................... 8
Front Wheel............................................................................................ 8
Rear Wheel ............................................................................................. 9
www.pro-team.com 866.888.2168
ATTENTION
Before servicing any part or
proceeding with any repair
procedure on any ProTeam vacuum,
ALWAYS disconnect the vacuum
from power source.
View Upright Vacuum
Wiring Schematic
at www.pro-team.com

www.pro-team.com 866.888.2168 1
Base Cover
Remove brush
1.
Remove cover - Lift up on one side
3.
Remove five (5) (M4 x 16mm length) screws
2.
To Reassemble. Repeat steps in reverse.

Clutch, LED Front Light, Belts, and Control Boards
2 www.pro-team.com 866.888.2168
Lift straight up on sensor control board, do not
lift by wires
4.
Remove rubber bumper - Pull straight up
1. Remove lens - Lift up on corner
2.
Remove LED light - Lift straight up on sensor
control board, do not lift by wires
5.
Remove RPM sensor - Remove screw
(M4 x 16mm length)
3.
6. Remove printed circuit board - Remove two (2)
screws (M4 x 16mm length)

www.pro-team.com 866.888.2168 3
Clutch, LED Front Light, Belts, and Control Boards
Lift up on control board
7.
Remove clutch assembly - Slide belt off pulley
9. Remove clutch assembly 10.
Remove clutch assembly - Remove two (2)
(M3 x 12mm length) screws
8.
To Reassemble. Repeat steps in reverse.

Filter Bag Housing
4 www.pro-team.com 866.888.2168
Lift up on bag housing and slide belt off motor
pulley
4.
Remove power head hose from bag housing
3.
Remove filter bag housing - Tilt filter bag
housing back
1. Remove two (2) (M4 x 16 mm length) screws
and bracket on each side
2.
To Reassemble. Repeat steps in reverse.

www.pro-team.com 866.888.2168 5
Foot Pedal
Remove plastic sleeve bearing each side - pull
straight off
2.
Remove foot petal
1. Tilt/rotate pedal forward (wear gloves to prevent
cuts from possible sharp edges in this assembly) -
Lift up on foot pedal
2.
Remove rear bag housing cover - Remove
nine (9) (M4 x 20mm length) screws
1.
Motor
To Reassemble. Repeat steps in reverse.

Motor
6 www.pro-team.com 866.888.2168
Lift motor assembly upward
8.
Remove gasket
7.
Remove air separator and motor - Remove
two (2) (M4 x 20mm length) screws
6.
Remove steel sleeve bearing on each side - Pull
straight off
3. Remove filter plate - Remove four (4) screws
(M4 x 20mm length)
4.
Remove filter door on each side
5.

Lift wiring harness upward
9.
Motor
Remove air separator - Remove two (2) (M4 x
20mm length) screws
10.
Remove upper motor housing - Remove six (6)
(M4 x 16mm length) screws
11.
To Reassemble. Repeat steps in reverse.
www.pro-team.com 866.888.2168 7
Remove motor brush assembly - Remove two
(2) (M4 x 16mm length) screws
12.
Pinch tab end and pull to release
13.

Power Head Hose
Remove center wheel - Pull wheel upwards -
Slide wheel off shaft
1.
Remove hose by twisting/unthreading
2.
Remove power head hose - Remove four (4)
(M4 x 16 mm length) screws
1.
To Reassemble. Repeat steps in reverse.
Front Wheel
8 www.pro-team.com 866.888.2168
To Reassemble. Repeat steps in reverse.