Pro-tec Algo-Tec 6300 User manual

93-508-08 Issue 2 Page 1of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
ISSUE DATE DETAILS OF CHANGE CHANGED
BY
104/07/01 ORIGINAL ISSUE -
221/11/02 UPDATE TO SOFTWARE VERSION 4.43 M.G.D
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 2of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
Table of Contents
O
OV VE ER RV VI IE EW W.................................................................................................................................................3
1.1 CONTROL PANEL.............................................................................................................................3
1.2 DEVICES............................................................................................................................................3
C
CO ON NT TR RO OL L F FU UN NC CT TI IO ON NS S............................................................................................................................4
2.1 SYSTEM NORMAL............................................................................................................................4
2.2 FIRE SIGNALS...................................................................................................................................4
2.3 SILENCE ALARMS............................................................................................................................4
2.4 RESETTING FIRE EVENTS...............................................................................................................5
2.5 SOUND ALARMS ..............................................................................................................................5
2.6 TO ACCEPT THE CURRENT CONDITION.......................................................................................5
U
US SE ER R M ME EN NU US S.............................................................................................................................................6
I
IS SO OL LA AT TI IO ON N F FU UN NC CT TI IO ON NS S...........................................................................................................................7
3.1 ISOLATING AN ADDRESS...........................................................................................................7
3.2 VIEWING THE ISOLATED ADDRESSES.....................................................................................7
3.3 ISOLATING A ZONE.....................................................................................................................8
3.4 VIEWING THE ISOLATED ZONES..............................................................................................8
3.5 CLEARING ALL ISOLATIONS.....................................................................................................9
3.6 FIRE LINK DISABLEMENT / ENABLEMENT.............................................................................9
S
SE ET T T TI IM ME E & & D DA AT TE E....................................................................................................................................10
C
CL LE EA AR RI IN NG G S SY YS ST TE EM M F FA AU UL LT T / / C CH HA AN NG GE E................................................................................................10
A
AD DV VA AN NC CE ED D O OP PT TI IO ON NS S.............................................................................................................................11
6.1 PRINTER FUNCTIONS................................................................................................................11
6.1.1 PRINTING ANALOGUE VALUES....................................................................................................... 12
6.1.2 DEVICES RETURNING ANALOGUE VALUES OUTSIDE A CERTAIN RANGE .............................. 13
6.1.3 PRINTING THE EVENT LOG .............................................................................................................. 14
6.1.4 PRINTING CURRENT EVENTS........................................................................................................... 14
6.1.5 PRINTING DEVICE DATA .................................................................................................................. 15
6.1.6 PRINTING THE PROGRAM MATRIX ................................................................................................. 16
6.1.7 PRINTING THE DELAY DATA........................................................................................................... 17
6.1.8 CANCELING THE PRINTOUT............................................................................................................. 17
6.2 VIEWING THE EVENT LOG.......................................................................................................18
6.3 VIEWING ANALOGUE VALUES...............................................................................................19
6.4 VIEWING ADDRESS TEXT ........................................................................................................19
6.5 EXCHANGE DEVICES................................................................................................................20
6. 6 DISABLE OUTPUTS...................................................................................................................21
6. 7 LAMP TEST................................................................................................................................21
6.8 WALK TEST ................................................................................................................................21
A
AP PP PE EN ND DI IX X A A - - K KE EY Y T TO O A AN NA AL LO OG GU UE E V VA AL LU UE ES S......................................................................................22
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 3of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
O
OV VE ER RV VI IE EW W
The 6300 panel drives up to four digital addressable loops with up to 191 addresses each. However the
number of detection devices and manual call points must be limited to a maximum of 512 in order to comply
with En54 part 2.
An addressable fire alarm system can pinpoint the location of an activated device because each device is
associated with an address. The advantage of an addressable system is that up to 191 different addresses are
possible on the same pair of wires. Each address is assigned to any of the zones available, zoning is done on
site by the commissioning engineer.
1.1 CONTROL PANEL
On the 6300 panel, all user control functions mentioned in this document are accessible after opening the
lockable windowed door.
The 6300 panel communication capabilities enable it to be connected to other 6300 panels through a secure
network. Alternatively, the 6300 panel can be used as a standalone panel. In either case repeat panels can be
connected to the system.
1.2 DEVICES
A digital addressable loop uses sensors instead of trigger devices. There are several different types of digital
addressable sensors available. For a list of available devices refer to appendix A.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 4of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
SYSTEM NORMAL HH:MM:SS DD/MM/YY
FIRE XX of XX ZONE XX LOOP XX ADDR XXX
Location text . . .
C
CO ON NT TR RO OL L F FU UN NC CT TI IO ON NS S
All control functions are accessible with the hinged plastic door open.
2.1 SYSTEM NORMAL
When the system is in a state such that there are no active faults and no fires the display will show: -
The state of the panel, the time and date are displayed on the top line of the LCD.
If it has been programmed on commissioning with a site-specific banner text, it will appear on the bottom line
of the display.
If the message “Maintenance Service Due” appears in place of the banner text, it means the panel needs to be
serviced by a qualified engineer.
2.2 FIRE SIGNALS
On hearing the FIRE ALARM: -
1) Evacuate the premises IMMEDIATELY.
2) Send for the FIRE BRIGADE.
3) DO NOT RE-ENTER the premises until authorised by the FIRE OFFICER in charge.
The display will show the details of the fire event, in the form: -
2.3 SILENCE ALARMS
Pressing ‘SILENCE’ after any FIRE event will cause the alarms to silence and the buzzer to change operation
from the fast pip to a slow pulse. The fast pip is an indication that the external alarm outputs are activated.
DO NOT at this stage attempt to ‘RESET’ the system until the cause of the fire has been established.
If the panel has not been programmed with location text, the bottom line of the display will remain blank.
The alarms can be resounded at any time by pressing ‘sound alarms’ button (refer to section 2.5 for details).
Manual call points must be physically reset. Automatic sensors must be visually checked to determine the
operated sensor. Further fire signals from other addresses will automatically re-sound the alarms.
Note: On a networked system, the silence command is network wide (global), not panel specific.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 5of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
SYSTEM IN RESET
ALARMS ON
2.4 RESETTING FIRE EVENTS
After silencing the alarms and establishing the cause of fire, press the ‘RESET’ button.
The panel will perform a lamptest, and then the display shows: -
The fire condition will re-start if an automatic sensor or a manual call point continues to operate.
Note: On a networked system, the reset command is network wide (global), not panel specific.
2.5 SOUND ALARMS
To sound ALL alarms, press the ‘SOUND ALARMS’ button.
All the alarm outputs will sound, the buzzer will produce a fast pip, and the display shows: -
Pressing the ‘SILENCE’ button cancels the SOUND ALARMS condition.
The SOUND ALARMS function can be initiated at any time, including during alarm or silenced conditions
and from within the user menus.
Note: On a networked system, the sound alarms command is network wide (global), not panel specific.
2.6 TO ACCEPT THE CURRENT CONDITION
If the system has entered a FIRE / FAULT condition, pressing the ‘ACCEPT’ button: -
1) Silences the internal buzzer (further fire / fault events will re-activate the internal buzzer).
2) Changes fire / fault indications from flashing to steady (further ones will start indications flashing again).
3) Holds the current display on the LCD for a few seconds.
4) Initiates the printing of events (where a printer is fitted).
Note: On a networked system, the accept command is network wide (global), not panel specific.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 6of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
U
US SE ER R M ME EN NU US S
The user menus are accessed by pressing the ‘MENU’ button.
The following buttons are used for navigating the menu functions: -
MENU Used to enter the user menus and to return back a menu level.
NEXT Used to move forward through the menu options and within a programming function to
increment or change the variable in question.
PREVIOUS Used to move back through the menu options and within a programming function to
decrement or change the variable in question.
ACCEPT Used to select a menu option and to accept and move on to the next variable within a
programming function.
When changing a value or option within a programming function, a flashing cursor indicates the variable
currently being edited. FIGURE 1: Menu Structure
The reception of a fire state from any device automatically exits the user menus. This also occurs if no buttons
are pressed for 10 minutes.
When the ‘MENU’ button is pressed, the display shows the user ‘main menu’ options.
The ‘NEXT’ and ‘PREVIOUS’ buttons are used to cycle the display through the ‘main menu’ options, which
are as follows: -
ISOLATION MENUS
SET UP TIME
CLEAR SYSTEM FAULT / CHANGE
ADVANCED OPTIONS
Pressing the ‘ACCEPT’ button selects the current menu option shown on the display.
Pressing the ‘MENU’ will then bring the user out of the menu option and back into the ‘main menu’ area.
Pressing the ‘MENU’ button whilst in the ‘main menu’ exits the user menus.
Isolation Menus Set Up Time Clear System Fault / Change Advanced Options
+ Printer Menus
Display Event Log
Read Analogue Data
View Text
Exchange Devices
RVAV
Disable Outputs
Lamp Test
+ Walk Test
Analogue Values
Analogue Values Outside Limits
Event Log
Active Events
Device Data
Program Matrix
Delay Data
Abort Printout
Isolate Address
View Addresses Isolated
Isolate zone
View Zones Isolated
Normalise Disablements
* Fire Link Disablement
+ Available if set when commissioned
* Not available if facility provided by a keyswitch
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 7of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
SYSTEM NORMAL HH:MM:SS DD/MM/YY
XX ADDR ISOLATED XX ZONES ISOLATED
LOOP XX ADDRESS XXX NORMAL
Location text . . .
ADDRESS ISOLATED :-
LOOP XX ADDRESS XX
I
IS SO OL LA AT TI IO ON N F FU UN NC CT TI IO ON NS S
Find the ‘ISOLATION MENUS?’ option from the ‘main menu’ using the ‘NEXT’ and ‘PREVIOUS’ buttons.
Press ‘ACCEPT’ to enter the ‘Isolation Menu’ through which access to all isolation functions is gained.
The ‘Isolation Menus’ sub-menu is as follows: -
ISOLATE ADDRESS
VIEW ADDRESSES ISOLATED (not available if no address isolated)
ISOLATE ZONE
VIEW ZONES ISOLATED (not available if no zone isolated)
NORMALISE DISABLEMENTS
FIRE LINK DISABLEMENT (not available if this facility is provided by a keyswitch)
If addresses or zones are isolated, the banner text line of the quiescent display is replaced with the isolation
information. This will produce the following display: -
Note: On a networked system, all isolations and disablements are panel specific.
3.1 ISOLATING AN ADDRESS
Find the ‘ISOLATE ADDRESS?’ option from the ‘Isolation Menus’ using ‘NEXT’ and ‘PREVIOUS’ buttons.
Press ‘ACCEPT’ to enter the menu option. The LCD displays:
To isolate an address select the loop number using ‘NEXT/PREVIOUS’, press ‘ACCEPT’ to move the cursor to
the address position. Select the address of the device to be isolated using ‘NEXT/PREVIOUS’.
Press ‘ACCEPT’ to move the cursor to the ‘NORMAL/ISOLATED’ position.
Pressing ‘NEXT/PREVIOUS’ toggles the address between ‘NORMAL and ‘ISOLATED’ states.
Use the ‘MENU’ button to return to the isolation menus.
3.2 VIEWING THE ISOLATED ADDRESSES
Find the ‘VIEW ADDRESSES ISOLATED?’ option from the ‘Isolation Menus’ using the ‘NEXT/PREVIOUS’
buttons. On pressing ‘ACCEPT’ if any addresses are isolated the LCD displays the first isolated address: -
Pressing either ‘NEXT’ or ‘PREVIOUS’ scrolls through any other addresses currently isolated.
If no addresses are isolated, this function becomes unavailable.
Use the MENU button to return to the ‘Isolation Menus’.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 8of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
ZONE ISOLATED :-
ZONE XX
ZONE XX NORMAL
3.3 ISOLATING A ZONE
Find the ‘ISOLATE ZONE?’ option from the ‘Isolation Menus’ using the ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’ to enter the menu option. The LCD displays:
To isolate a zone select the zone to be isolated using ‘NEXT/PREVIOUS’.
Press ‘ACCEPT’ to move the cursor to the ‘NORMAL/ISOLATED’ position.
Pressing ‘NEXT/PREVIOUS’ toggles the zone between NORMAL and ISOLATED states.
Use the ‘MENU’ button to return to the ‘Isolation Menus’.
3.4 VIEWING THE ISOLATED ZONES
Find the ‘VIEW ZONES ISOLATED?’ option from the isolation menus using ‘NEXT/PREVIOUS’ buttons.
On pressing ‘ACCEPT’, if any zones are isolated the LCD displays the first of the isolated zones: -
Pressing either ‘NEXT’ or ‘PREVIOUS’ scrolls through any other zones currently isolated.
If no zones are isolated this function becomes unavailable.
Use the ‘MENU’ button to return to the ‘Isolation Menus’.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 9of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
NORMALISE ISOLATED ZONES/ADDRESSES
NO
FIRE LINK DISABLEMENT ?
NO
3.5 CLEARING ALL ISOLATIONS
This menu can be used as a quick method to enable all zones and addresses.
Find the ‘NORMALISE DISABLEMENTS?’ option from the ‘Isolation Menus’ using the ‘NEXT’ and
‘PREVIOUS’ buttons. On pressing ‘ACCEPT’ the display shows: -
Pressing either ‘NEXT’ or ‘PREVIOUS’ toggles between the ‘YES/NO’ options available. Pressing ‘ACCEPT’
carries out the selected option and returns the user to the ‘Isolation Menus’. Disablements are normalised on
pressing accept when ‘YES’ is selected.
3.6 FIRE LINK DISABLEMENT / ENABLEMENT
This menu allows the fire link to be disabled or enabled. This facility is not available if it is already provided
by a keyswitch.
Find the ‘FIRE LINK DISABLEMENT?’ option from the ‘Isolation Menus’ using ‘NEXT’ and ‘PREVIOUS’
buttons. On pressing ‘ACCEPT’ the display shows: -
Pressing either ‘NEXT’ or ‘PREVIOUS’ toggles between the ‘YES/NO’ options available. Pressing ‘ACCEPT’
carries out the selected option and returns the user to the ‘Isolation Menus’. The Fire Link will be disabled on
pressing accept when ‘YES’ is selected. Both DISABLEMENT and FIRE LINK DISABLED LED’s will then
be switched on.
Note: On a networked system, the fire link disablement is panel specific.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 10 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
HH:MM:SS DD/MM/YY
^^
CLEAR SYSTEM FAULT/CHANGES ?
NO
S
SE ET T T TI IM ME E & & D DA AT TE E
Find the ‘SET UP TIME?’ option from the ‘main menu’ using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’ the LCD displays: -
Use ‘ACCEPT’ to scroll through all the sections of the time and date (current selection shown by ^^). When
the pointer is under a variable that requires changing, use the ‘NEXT/PREVIOUS’ buttons to
increment/decrement the variable.
Press ‘MENU’ to set the new time and return to the user ‘main menu’.
Note: On a networked system, the new time and date are sent across the network to all panels (global).
C
CL LE EA AR RI IN NG G S SY YS ST TE EM M F FA AU UL LT T / / C CH HA AN NG GE E
This option is used to clear a system fault or a system change:
•A system fault occurs when the panel has restarted whilst already powered up (warm start).
Either a hardware reset or the software forcing a hardware reset can be the cause of this fault.
The FAULT LED and SYSTEM FAULT LED will change from flashing to being steady upon pressing
the ‘ACCEPT’ button. The display will show diagnostic information that can be printed (if a printer has
been fitted). This diagnostic information should be recorded.
•A system change occurs following the exchange of one or more devices. There is no need to record the
diagnostic information following the exchange. The panel needs a fresh start to initialise all the devices.
The software will force a hardware reset upon clearing the fault hence restarting the panel (warm start).
The buzzer will emit a short beep to signal this. The panel once restarted will require the system fault to be
cleared. There is no need to record the diagnostic information following the panel restart.
Both types of faults should be cleared as shown below.
Select the option ‘CLEAR SYSTEM FAULT / CHANGE?’ from the main menu using ‘NEXT/PREVIOUS’.
The display shows: -
Press ‘NEXT/PREVIOUS’ buttons to select the ‘YES’ option. Now press ‘ACCEPT’ to clear the fault.
On a system fault (FAULT and SYSTEM FAULT LED’s active), the LCD will return to the ‘main menu’.
On a system change, the panel will reset itself in order to get a fresh start. This will be followed by a system
fault because the panel has restarted whilst already powered up (warm start). This fault should be cleared as
described above.
Note: On a networked system, this command is panel specific.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 11 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
A
AD DV VA AN NC CE ED D O OP PT TI IO ON NS S
Find ‘ADVANCED OPTIONS?’ from the ‘main menu’ using the ‘NEXT’ and ‘PREVIOUS’ buttons.
Press ‘ACCEPT’ to enter the ‘Advanced Options Menu’.
The user is now presented with a sub-menu through which access to all other user functions is gained.
PRINTER MENUS (not available if no printer provided)
DISPLAY EVENT LOG
READ ANALOGUE DATA
VIEW TEXT
EXCHANGE DEVICES
RVAV
DISABLE OUTPUTS
LAMP TEST
WALK TEST (Only available if configured upon commissioning to be available)
6.1 PRINTER FUNCTIONS
Find the ‘PRINTER MENUS?’ option from the ‘Advanced Options’ menu using ‘NEXT/PREVIOUS’ buttons.
Note: The printer menus will only be available if the panel has been programmed as having a printer installed.
Press ‘ACCEPT’ to enter the ‘Printer Menu’.
The user is now presented with a sub-menu through which access to all printer function is gained.
The ‘Printer Menus’ sub-menu is as follows: -
ANALOGUE VALUES
ANALOGUE VALUES OUTSIDE LIMITS
EVENT LOG
ACTIVE EVENTS
DEVICE DATA
PROGRAM MATRIX
DELAY DATA
ABORT PRINTOUT
Note: On a networked system, the printer functions are panel specific.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 12 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
PRINT ANALOGUE VALUES ON LOOP XX
BETWEEN ADDRESSES XXX AND XXX
6.1.1 PRINTING ANALOGUE VALUES
Find the ‘ANALOGUE VALUES’ option from the ‘Printer Menu’ option using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
Choose the loop from which the device values are to be printed using ‘NEXT/PREVIOUS’. Press ‘ACCEPT’ to
move the cursor to the start address value. Use ‘NEXT/PREVIOUS’ to alter the address start value then press
‘ACCEPT’ to move on to the address finish value and set this in the same way. Press ‘ACCEPT’ to activate the
printout. The average value for each address is also printed for comparison. The average value is a long-term
function, which is updated every 8 hours.
Example: -
Note: -The analogue values will not be printed if the end address is not set above the start address.
To cancel printing, see section 6.1.8 CANCELING THE PRINTOUT. See Appendix A to interpret the values.
Press the ‘MENU’ button to return to the ‘Printer Menus’.
***************************************
LOOP 1 ADDRESS DATA
10:45:48 16/01/00
ADDR. DEVICE TYPE CHANNEL 1 CHANNEL 2
VAL AVE. VAL AVE.
01 ZAI 85
02 ZAI 85
06 OPTHEAT 55 58 118 115
11 ION 104 104
****************************************
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 13 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
PRINT ALL DEVICES ABOVE XX
6.1.2 DEVICES RETURNING ANALOGUE VALUES OUTSIDE A CERTAIN RANGE
Find the ‘ANALOGUE VALUES OUTSIDE LIMITS’ option from the ‘Printer Menus’ using
‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
1) Use ‘NEXT/PREVIOUS’ buttons to scroll through all of the detector type to be printed. Press ‘ACCEPT’.
2) Use ‘NEXT/PREVIOUS’ to select either ABOVE or BELOW. Press ‘ACCEPT’.
3) Set the analogue value to the level of interest using ‘NEXT/PREVIOUS’.
4) Press ‘ACCEPT’ to print. A printout will appear for all loops.
Example printout for ‘ALL’ devices ‘BELOW’ an analogue value of 85: -
To cancel printing, see section 6.1.8 CANCELING THE PRINTOUT.
Press ‘MENU’ to return to the ‘Printer Menus’.
****************************************
LOOP 1 ANALOGUE VALUES BELOW 85
10:45:48 16/01/00
ADDR. DEVICE TYPE CHANNEL 1 CHANNEL 2
VAL AVE. VAL AVE.
01 OPTHEAT 55 58 118 115
02 OPTHEAT 70 70 134 134
06 OPTHEAT 55 58 118 115
11 OPTICAL 55 56
****************************************
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 14 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
PRINT ALL ACTIVE EVENTS
PRINT :-
ALL EVENTS ONWARD FROM DD/MM/YY
6.1.3 PRINTING THE EVENT LOG
Find the ‘EVENT LOG’ option from the ‘Printer Menus’ option using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
1) Select the type of event to print using ‘NEXT/PREVIOUS’.
The choices are ALL EVENTS, ALL FIRES or ALL FAULTS. Press ‘ACCEPT’.
2) Set the start date of the print.
Use ‘NEXT/PREVIOUS’ to change the day. Press ‘ACCEPT’.
Use ‘NEXT/PREVIOUS’ to change the month. Press ‘ACCEPT’.
Use ‘NEXT/PREVIOUS’ to change the year.
3) When the date is set correctly, press ‘ACCEPT’ to initiate printing.
No printing occurs if an impossible date is entered.
To cancel printing, see section 6.1.8 CANCELING THE PRINTOUT.
Use the ‘MENU’ button to return to the ‘Printer Menus’.
6.1.4 PRINTING CURRENT EVENTS
Find the ‘ACTIVE EVENTS’ option from the printer functions menu using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
A print of the events in the log which are active (faults which are still present and fires which have not been
reset) will begin on the next press of ‘ACCEPT’.
Also, the menu exits to the ‘Printer Menus’ on the pressing the ‘ACCEPT’ button.
To cancel printing, see section 6.1.8 CANCELING THE PRINTOUT.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 15 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
PRINT DEVICE DATA
6.1.5 PRINTING DEVICE DATA
Find the ‘DEVICE DATA’ option from the ‘Printer Menus’ option using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
Press ‘ACCEPT’ and the panel will print out device data for all loops, and exit back to the ‘Printer Menus’.
Device Data example printout: -
To cancel printing, see section 6.1.8 CANCELING THE PRINTOUT.
****************************************
LOOP 1 ALLOCATION DATA 3 DEVICES
09:57:48 16/01/00
ADD SERNUM ZN IG OG MODE TYPE VR GG DG
01 765640 09 01 01 FIX MCP 00 00 00
02 0001CC 01 04 01 GEN OPTICAL 00 00 00
03 B0F0DF 03 05 01 GEN ION 00 00 00
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 16 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
PRINT MATRIX DATA
6.1.6 PRINTING THE PROGRAM MATRIX
Find the ‘PROGRAM MATRIX’ option from the ‘Printer Menus’ using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
Press ‘ACCEPT’ and the program matrix will be printed, and exit back to the ‘Printer Menus’.
Program Matrix printout example for output groups 1 to 96: -
To cancel printing, see section 6.1.8 CANCELING THE PRINTOUT.
****************************************
PROGRAM MATRIX DATA
09:57:48 16/01/00
TIMEOUT
| INPUT
| GROUP
| | OUTPUT GROUP
| | 81 83 85 87 89 91 93 95
| | 82 84 86 88 90 92 94 96
:
:
TIMEOUT
| INPUT
| GROUP
| | OUTPUT GROUP
| | 01 03 05 07 09 11 13 15
| | 02 04 06 08 10 12 14 16
00:00 01 C C C C C C C C C C C C C C C C
00:00 02 P P P P C - P P - --CPP--
00:00 03 P P P C P C C P P - ---PP-
00:00 06 P P P P C C P P - --CPP-P
00:00 07 P P P P P C C P P - ---PP-
00:00 08 P P P - C C - C C C C C C P - -
00:00 12 P P P - C C - C C C C C C P C -
00:00 13 P P P - C - P C C C C C C P P -
00:00 14 P P P P C C P P - --CPP-C
00:00 16 P P P - C C - C C C C C C P P -
PULSE ON TIME 03.00 OFF TIME 03.00
MASTER TIMEOUT 00:01
****************************************
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 17 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
DELAY DATA
ABORT PRINTOUT
NO
6.1.7 PRINTING THE DELAY DATA
Find the ‘DELAY DATA’ option from the printer functions menu using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
Press ‘ACCEPT’ to print a copy of the full delay matrix and exit back to the ‘Printer Menus’.
Example Delay Data printout: -
To cancel printing, see section 6.1.8 -CANCELING THE PRINTOUT.
6.1.8 CANCELING THE PRINTOUT
Find the ‘ABORT PRINTOUT’ option from the ‘Printer Menus’ using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
Use ‘NEXT/PREVIOUS’ to toggle between ‘YES’ and ‘NO’. To abort the printout, press ‘ACCEPT’ when the
‘YES’ option is selected. The screen returns to the ‘Printer Menus’.
****************************************
PROGRAM DELAY DATA
09:57:48 16/01/00
INPUT
GROUP OUTPUT GROUP
|
| 01 02 03 04
01 00:00 00:00 00:00 00:00
02 00:00 00:00 00:00 00:00
03 00:00 00:00 00:00 00:00
04 00:00 00:00 00:00 00:00
05 00:00 00:00 00:00 00:00
: : : : :
27 00:00 00:00 00:00 00:00
28 00:00 00:00 00:00 00:00
29 00:00 00:00 00:00 00:00
30 00:00 00:00 00:00 00:00
31 00:00 00:00 00:00 00:00
32 00:00 00:00 00:00 00:00
:
:
INPUT
GROUP OUTPUT GROUP
|
| 29 30 31 32
01 00:00 00:00 00:00 00:00
02 00:00 00:00 00:00 00:00
03 00:00 00:00 00:00 00:00
: : : : :
30 00:00 00:00 00:00 00:00
31 00:00 00:00 00:00 00:00
32 00:00 00:00 00:00 00:00
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 18 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
XX FIRE EVENTS XX FAULT EVENTS
RESET EVENT COUNTS? NO ALL EVENTS
EVENT XX of YY HH:MM:SS DD/MM/YY
Type of Event Zone, Loop, Address (if applicable)
EVENT XX of YY HH:MM:SS DD/MM/YY
Location text . . .
6.2 VIEWING THE EVENT LOG
The most recent 100 events are recorded in the event log along with the time and date at which each occurred.
Find the ‘DISPLAY EVENT LOG?’ option from the ‘Advanced Options’ menu using ‘NEXT/PREVIOUS’.
Press ‘ACCEPT’. The LCD displays: -
This screen shows the number of fire events and fault events since power-up or since the last event count reset.
To reset the event counts, toggle between ‘YES’ and ‘NO’ using ‘NEXT/PREVIOUS’.
1) To clear the event counts select ‘YES’ and press ‘ACCEPT’, select ‘NO’ otherwise.
Notice that the ‘Fire Events’ count and the ‘Fault Event’ counts have been cleared.
Note: Resetting the counts does not clear the event log.
2) Press ‘ACCEPT’ again to select all events or faults only (if active faults are present on the system).
The LCD now shows: -
The event number indicates the order in which the events occurred, EVENT 01 being the most recent. If an
event is still active, an asterisk appears by the event number.
Use ’NEXT/PREVIOUS’ to increment/decrement the event number. The time and date for each event is shown
in the top right-hand corner of the LCD. This is followed on the bottom line by the panel number (if the panel
is part of a network system), the event description and the location information (Zone, Loop and Address if
event relates to a device on the loop).
To view the text associated with the address of the event press ‘ACCEPT’. The LCD displays: -
Press ‘ACCEPT’ again to return to the event type and address display.
Press ‘MENU’ to return to the ‘Advanced Options’ menu.
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 19 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
LP1 ADD 01 02 03 04 05 06 07 08
Ch1 T00 55 50 51 55 50 49 57 56
LOOP XX ADDRESS XX devtype MODE XXXXXXX
Text Associated With Address
6.3 VIEWING ANALOGUE VALUES
Find the ‘READ ANALOGUE DATA?’ option from the ‘Advanced Options’ menu using ‘NEXT’ and
‘PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
The analogue value for each address on the top line is displayed directly below it. The values are updated every
3 seconds. As each value is updated a ‘-‘ is toggled on and off in front of the address. See Appendix A to
interpret the values.
1) Use ‘NEXT/PREVIOUS’ to select the loop then press ‘ACCEPT’ to move the cursor to the ADD position.
2) Use ‘NEXT/PREVIOUS’ to view the previous/next block of eight addresses on the loop of interest.
Press ‘ACCEPT’ to move the cursor to the channel position.
3) Use ‘NEXT/PREVIOUS’ to toggle between channel 1 and 2. Press ‘ACCEPT’ to move the cursor to Tnn.
4) Use ‘NEXT/PREVIOUS’ to select a different time average. Values above T04 are for diagnostic purposes.
Pressing ‘ACCEPT’ moves the cursor back to the loop number.
Press ‘MENU’ to return to the ‘Advanced Options’ menu.
Note: On a networked system, only the panel’s own loop devices analogue values can be viewed (not global).
6.4 VIEWING ADDRESS TEXT
The pre-programmed text associated with each address can be viewed.
Find the ‘VIEW TEXT?’ option from the ‘Advanced Options’ menu using ‘NEXT/PREVIOUS’ buttons.
Press ‘ACCEPT’. The LCD displays: -
The text displayed along the bottom line of the display is that which corresponds to the loop number and
address shown on the top line.
1) Use ‘NEXT/PREVIOUS’ to select the loop then press ‘ACCEPT’ to move to the address position.
2) Use ‘NEXT/PREVIOUS’ to select the address then press ‘ACCEPT’ to move back to the loop position.
Press ‘MENU’ to return to the ‘Advanced Options’ menu.
Note: On a networked system, only the panel’s own loop devices text can be viewed (not global).
http://www.firealarmengineers.com

93-508-08 Issue 2 Page 20 of 22 Copyright Protec Fire Detection PLC
6300 OPERATING MANUAL
SELECT LOOP X
LX A -- Press NEXT for Missing Devices
L1 A 02 OPTHEAT OLD 1E8AA1 NEW ------
L1 A 02 OPTHEAT OLD 1E8AA1 NEW 1E8A97
CONFIRM EXCHANGE:- No
SAVE ALTERATIONS YES
6.5 EXCHANGE DEVICES
It is important that the exchange procedure is followed precisely in the order described here i.e. NO
devices must be added to the system until the ’EXCHANGE DEVICES’ menu option has been selected
on the panel driving the device.
Find the ‘EXCHANGE DEVICES’ option from the ‘Advanced options’ menu using ‘NEXT/PREVIOUS’.
Press ‘ACCEPT’. The LCD displays: -
No more than 8 devices can be exchanged at a time. Follow the exchange procedure as shown below:
1. Record the loop and address of the device to be exchanged.
2. Ensure that the replacement device is of the same type as the device to be removed.
3. Record the serial number of the replacement device.
4. Exchange the two devices.
5. Record the serial number of the exchanged device.
The replacement device should pulse its led for 2 seconds on and two seconds off to show that it has been
detected by the system. Type checking cannot be performed by the system at this stage so the replacement may
yet be unsuitable.
Use ‘NEXT/PREVIOUS’ to select the loop then press ‘ACCEPT’. The LCD will display:
Pressing NEXT will display the first missing device, in this example loop 1, address 02:
If this device is the one to be exchanged press ‘ACCEPT’ and the cursor will move to the right hand end of the
display. Use ‘NEXT/PREVIOUS’ to cycle through the serial numbers of devices that have been added. When
the correct replacement device is displayed, press ‘ACCEPT’. The display shows:
Use ‘NEXT’ to select ‘Yes’ then press ‘ACCEPT’. At this point, the exchange has not been saved. Repeat this
exchange procedure for all exchanged devices then press ‘MENU’ until the panel exits from ‘Advanced
options’. The display will show the software version screen; then it will display:
Press ‘ACCEPT’ to save the changes else press ‘NEXT’ to select ‘No’. If ‘Yes’ is selected then the system will
save the changes and revert to the normal display. The saving of data will take a minute or two. A system
change fault will be generated. To clear the fault, see section CLEARING SYSTEM FAULT / CHANGE.
Note: On a networked system, only the panel’s own loop devices can be exchanged (not global).
http://www.firealarmengineers.com