Prodesign Furniture Cannes Curved ETU 160 User manual

Please read the Assembly Instructions carefully
before assembling.
Imported By PRODESIGN FURNITURE PTY LTD.
521174-01-01 2023-4-25
Assembly Instructions
Cannes Curved ETU 160 - White Oak
400mm
1600mm
450mm
1-14

Warning: In order to prevent overturning, this product must be used with the wall attachment device provided.521174-01-01 2023-4-25
2-14

Daily Care：
Water and other liquids can cause discoloration and damage to
the surface. In case any liquids are spilled on the surface, remove
immediately with a clean cloth. Avoid rubbing the spilled liquid
into the veneer, but wipe gently, using a clean, firmly wrung
damp cloth. If stains or marks persist, seek professional help and
advice.
Wood expands and contracts according to the surrounding
humidity and temperature. In case of temperature and humidity
fluctuations, the wood might warp and/or crack. To avoid this,
do not place the furniture near a radiator or in hot surroundings.
Take care when moving the furniture across the floor. Do not
drag the furniture, as this can cause damage to both the
furniture and the floor.
521174-01-01 2023-4-25
3-14

4-14
1
2
2
521174-01-01 2023-4-25
NO. PARTS LIST QTY
(1) BODY 1
(2) LEG 2

5-14
521174-01-01 2023-4-25
(A) (B)
Ø8x30mm
(C)
4 x Bolt
M6x55mm (D)
1 x Allen key
4 x Wooden dowels
(E) (F)
M4mm
Ø16x1.5mmØ6/
Ø16x1.5mm
x Washer
4
Ø35x3mm
4 x Felt Pads
4 x Spring Washer

Step 1
You will need
Step 2
You will need
(A)
4 x Wooden dowels
A
x 2
2
Insert 4 x Dowels (A) into 2 x Legs (2) as shown.
4 x Bolt
(B) (C)
1 x Allen key
6-14
( ) (E)
A
D
x Washer
4
x Washer
4
BB
BB
1
2
2
521174-01-01 2023-4-25
B
C
D
E
Attach 2 x Legs (2) to Body (1) using 4 x Bolts (B), 4 x Spring Washers (C) and 4 x Washers (D).
Tighten the bolts with Allen Key (E) .

Step 3
Step 4
7-14
521174-01-01 2023-4-25
4 x Felt Pads
You will need
(F)
F
F
F
F
F
Attach 4 x Felt Pads (F) to the 4 x Legs.
Ⅱ Ⅲ
Open the door as shown.
: Loosen the screws.
Ⅱ: Rotate the magnetic push open clips 180deg to face outwards.
Ⅲ: Tighten screws 100%.

Step 5
8-14
Withhelp, carefullyturnthe ETU over.
521174-01-01 2023-4-25

Step 6
9-14
I. With help, move the ETU into position. Mark drilling points on the wall.
II. If necessary, remove the ETU and drill holes with sizes suitable for your wall fixings.
III. Install wall fixings in the holes.
IV. Fix the wall brackets to the wall with appropriate wall fixing screws.
V. Fasten the wall brackets to the underside of the top panel.
521174-01-01 2023-4-25

Step 7
10-14 2023-4-25
521175-01-01
Trash
Remove the plastic clips as shown and dispose.
You may adjust the height of the shelves now if you wish.

Step 8
11-14 2023-4-25
521175-01-01
If adjustment is necessary, please follow the steps below:
To move doors up or down:
loosen or tighten the screws on the hinge plate,
as showm.
To move doors in or out:
Loosen or tighten the screws on the hinge plate,
as shown.
To move doors left or right: loosen or
Loosen or tighten the screws to suit, as shown.

12-14 2023-4-25
521175-01-01
Step 9
To move doors up or down:
loosen or tighten the screws on the hinge plate,
as showm.
To move doors in or out:
Loosen or tighten the screws on the hinge plate,
as shown.
To move doors left or right: loosen or
Loosen or tighten the screws to suit, as shown.
If adjustment is necessary, please follow the steps below:

Step 10
13-14
max
40kg
max
20kg
2023-4-25
521175-01-01
Step 11
to
piston

14-14
THIS PRODUCT IS FINISHED WITH LACQUER
521174-01-01 2023-4-25