Prodesign Furniture Benji User manual

Please read the Assembly Instructions carefully
before assembling.
Imported By PRODESIGN FURNITURE PTY LTD.
520849-01-01 1-19 2022-02-24
Assembly Instructions
Benji - 180cm Entertainment Unit

2-19 2022-02-24
520849-01-01
Warning: In order to prevent overturning, this product must be used with the wall attachment device provided.

3-19 2022-02-24
520849-01-01
Daily Care：
Water and other liquids can cause discoloration and damage to
the surface. In case any liquids are spilled on the surface, remove
immediately with a clean cloth. Avoid rubbing the spilled liquid
into the veneer, but wipe gently, using a clean, firmly wrung
damp cloth. If stains or marks persist, seek professional help and
advice.
Wood expands and contracts according to the surrounding
humidity and temperature. In case of temperature and humidity
fluctuations, the wood might warp and/or crack. To avoid this,
do not place the furniture near a radiator or in hot surroundings.
Take care when moving the furniture across the floor. Do not
drag the furniture, as this can cause damage to both the
furniture and the floor.

4-19 2022-02-24
1
6
2
2
3
5
7
4
8
9
8
8
7
520849-01-01
NO. PARTS LIST QTY
(1) TOP PANEL 1
(2) SIDE PANEL
(3) DIVIDER PANEL 1
(4) BOTTOM PANEL
(5) LEG 5
(7) SHELF PANEL
(6) BACK PANEL
(8) DOOR PANEL
(9) DOOR PANEL
2(2) SIDE PANEL
1
3
1
1
2

18 x Locking Nut
Ø15x12mm
(A)
18 x Connecting Bolt
Ø6x44mm
(B)
Ø8x30mm
(C)
5 x Bolt
M6x40mm
(D)
(R)
1 x Allen key
22 x Wooden dowels
40 x Screws
Ø3.5x16mm
(E)
14 x Screws
Ø3.5x16mm
(F)
16 x Plastic Stopper
13.6x9x14mm
8 x Shelf support
Ø5x20mm
(L)
FK
17
(M)
4 x Hinge
( )( N)
2 x Bracket
(P)
8 x Bolts
Ø4x23mm
(K)
(G) (H)
4 x Handle
(J)
M4mm
(Q)
150x75x22mm
75x25x15mm
5-19 2022-02-24
520849-01-01
( )( S)
5 x Foot pad
70x30x3mm
4 x Hinge
FK 9
5 x Washer
Ø16x1.5mm
( )
Ø6/T
4 x Magnetic Door Catch 4 x Catch Plate

Step 1
You will need
Step 2
You will need
(C)
10 x Wooden dowels
C
C
x 5
5
Insert 10 x Dowels (C) into 5 x Legs (5) as shown.
5 x Bolt
(D) (R)
1 x Allen key
6-19 2022-02-24
4
D
R
5
520849-01-01
5
5
5
5
(S)
5 x Foot pad
S
S
S
S
S
4
S
(T)
5 x Washer T
Fix 5 x Legs (5) onto Bottom Panel (4) with 5 x Bolts (D), 5 x Washers (T) using Allen key (R).
Attach 5 x Foot Pads (S) to the Legs (5).

Step 3
You will need
(A) A
Step 4
You will need
(C)
12 x Wooden dowels
7-19 2022-02-24
2
3
C
C
C
C
C
C
C
C
x2
C
520849-01-01
A
A
A
4
A
A
A
A
A
A
Insert 12 x Dowels (C) into Panel (2 3) as shown./
9 x Connecting Bolt
Screw 9 x Connecting Bolts (A) into Bottom Panel (4) as shown.

Step 5
You will need
(B)
Step 6
8-19 2022-02-24
520849-01-01
2
3
4
B
BB
2
6
B
BB
B
BB
B
9 x Locking Nut
Slide Back Panel (6) into the grooves of Side Panels (2) and Bottom Panel (4).
4
2
2
Position 2 x Side Panels (2) and Divider Panel (3) to Bottom Panel (4) as shown.
Please make sure the locking nut holes are facing right on Divider Panel (3).
Insert 9 x Locking Nuts (B) into the Side Panels (2) and Divider Panel (3).
Use a screwdriver to turn the locking nuts clockwise to lock.

Step 7
You will need
12 x Screws
(F)
(P)(G)
(A)
Step 8
You will need
(B)
9-19 2022-02-24
A
FF
P
FF
G
A
A
A
A
A
A
A
A
A
1
520849-01-01
BBB
1
BBB
BBB
B
Connecting Bolt
2 x Bracket
9 x Locking Nut
9 x
Attach Top Panel (1) to the frame using 9 x Locking Nuts (B).
Use a screwdriver to turn the locking nuts clockwise to lock.
Door Catch
4 x Magnetic
Loosely attach 2 x Brackets (P) to Top Panel (1) using 4 x Screws (F).
Fix 4 x Magnetic Door Catch (G) to Top Panel (1) using 8 x Screws (F).
Screw 9 x Connecting Bolts (A) into Top Panel (1) as shown.

Step 9
You will need
16 x Screws
(E)
(Q)
2 x Screws
(F)
10-19 2022-02-24
E
F
Q
F
520849-01-01
Plastic Stopper
If necessary, adjust the assembly so that the diagonal measurements of the assembly are equal.
Fix the Back Panel (6) in place using 16 x Screws (E) and Plastic Stoppers (Q) and 2 x Screws (F) as shown.
16 x

Step 10
11-19 2022-02-24
520849-01-01
I. With help, move the Entertainment Unit into position. Mark drilling points on the wall.
II. If necessary, remove the Entertainment Unit and drill holes with sizes suitable for your wall fixings.
III. Install wall fixings in the holes.
IV. Fix the wall brackets to the wall with appropriate wall fixing screws.
V. Fasten the wall brackets to the underside of the top panel.

Step 11
You will need
(L)
L
12-19 2022-02-24
Step 12
You will need
6 x Screws
(E)
2 x Hinge
( )
M
(H)
E
M
E
E
E
H
8
520849-01-01
L
L
7
7
L
L
8 x Shelf support
Insert 8 x Shelf Supports (L) into desired locations on the Side and Divider panels.
Gently place the 2 x Shelf Panel (7) as shown.
Fix 2 x Hinges (M) to Door Panel (8) using 4 x Screws (E).
Fix 1 x Catch Plate (H) to Door Panel (8) using 2 x Screws (E) .
1 x Catch Plate

13-19 2022-02-24
Step 14
You will need
6 x Screws
(E)
2 x Hinge
( )
N
(H)
E
E
H
9
520849-01-01
Step 13
You will need
2 x Bolts
(K)
1 x Handle
(J)
JK
K
8
E
N
E
J
8J
8
Attach the door to the cabinet as shown.
Loosely attach 1 x Handle (J) to Door Panel (8) using 2 x Bolts (K).
Align Handle (J) to the Door Panel (8) and fasten Bolts (K).
1 x Catch Plate
Fix 2 x Hinges (N) to Door Panel (9) using 4 x Screws (E).
Fix 1 x Catch Plate (H) to Door Panel (9) using 2 x Screws (E) .

14-19 2022-02-24
You will need
6 x Screws
(E)
2 x Hinge
( )
N
(H)
E
E
H
8
520849-01-01
Step 15
You will need
2 x Bolts
(K)
1 x Handle
(J)
J
K
K
9
8
E
N
E
J9J9
1 x Catch Plate
Attach the door to the cabinet as shown.
Loosely attach 1 x Handle (J) to Door Panel (9) using 2 x Bolts (K).
Align Handle (J) to the Door Panel (9) as shown and fasten Bolts (K).
Step 16
Fix 2 x Hinges (N) to Door Panel (9) using 4 x Screws (E).
Fix 1 x Catch Plate (H) to Door Panel (8) using 2 x Screws (E) .

15-19 2022-02-24
You will need
6 x Screws
(E)
2 x Hinge
( )
M
(H)
E
E
H
8
520849-01-01
Step 17
You will need
2 x Bolts
(K)
1 x Handle
(J)
JK
K
8
E
M
E
J
8J
8
1 x Catch Plate
Attach the door to the cabinet as shown.
Loosely attach 1 x Handle (J) to Door Panel (8) using 2 x Bolts (K).
Align Handle (J) to the Door Panel (8) and fasten Bolts (K).
Step 18
Fix 2 x Hinges (M) to Door Panel (9) using 4 x Screws (E).
Fix 1 x Catch Plate (H) to Door Panel (8) using 2 x Screws (E) .

16-19 2022-02-24
Step 19
You will need
2 x Bolts
(K)
1 x Handle
(J)
J
K
K
8
520849-01-01
J8J8
Attach the door to the cabinet as shown.
Loosely attach 1 x Handle (J) to Door Panel (8) using 2 x Bolts (K).
Align Handle (J) to the Door Panel (8) and fasten Bolts (K).

17-19 2022-02-24
Step 20
520849-01-01
If adjustment is necessary, please follow the steps below:
Loosen the screws on the hinge plate and move the doors to suit.
Once doors are aligned,re-tighten the screws.
To move doors in or out:
Loosen or tighten the screws on the hinge plate, as shown.
To move doors left or right:
Loosen or tighten the screws to suit, as shown.
To move doors up or down:

Step 21
18-19 2022-02-24
max
40kg
520849-01-01
max
10kg
max
20kg

19-19 2022-02-24
THIS PRODUCT IS FINISHED WITH LACQUER
520849-01-01