Proma Fp-20a User manual

BENCH MILL MACHINE

Instruction manual

Please read this manual thoroughly and follow all directions carefully

IMPORTANT SAFETY INSTRUCTION

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS TOOL

Operator

COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO

ANY PRODUCT. THESE FACTORS MUST BE SUPPLIED BY THE OPERATOR.

PLEASE REMEMBER:

1. When using electric tools, machines or equipment, basic safety precautions should

always be followed to reduce the risk of fire, electric shock, and personal injury.

2. Keep work area clean. Cluttered areas invite injuries.

3. Consider work area conditions. Do not use machines or power tools in damp, wet, or

poorly lit locations. Do not expose equipment to rain, keep work area well lit. Do not

use tools in the presence of flam-mable gases or liquids.

4. Keep children away, all children should be kept away from the work area.

5. Guard against electric shock. Prevent body contact with grounded surfaces such as

pipes, radiators, ranges, and refrigerator enclosures.

6. Stay alert. Never operate if you are tired.

7. Do not operate the product if under the influence of alcohol or drugs. Read warning

labels on prescriptions to determine if your judgment or reflexes might be impaired.

8. Do not wear loose clothing or jewelry as they can be caught in moving parts.

9. Wear restrictive hair covering to contain long hair.

10.Use eye and ear protection.Always wear.

11.Keep proper footing and balance at all times.

12.Do not reach over or across running machines.

Before operations

1. Be sure the switch is OFF when not in use and before plugging in.

2. Do not attempt to use inappropriate attachments in an attempt to exceed the tool”s

capacity. Approved accessories are available from the dealer or machine maker.

3. Check for damaged parts, before using any tool, any part that appears damaged

should be carefully checked to determine that it will operate properly and perform its

intended function.

4. Check for alignment and binding of all moving parts, broken parts or mounting fixtures

and any other condition that may affect proper operation. Any part that is damaged

should be prop early repaired or replaced by a qualified technician.

5. Do not use the tool if any switch does not turn off and properly

Operation

1. Never force the tool or attachment to do the work of a larger industrial tool. It is

designed to do the job better and more safely at the rate for which it was intended.

2. Do not carry the tool by its power cord.

3. Always unplug the cord by the plug. Never yank the cord out of the wall.

4. Always turn off the machine before unplugging.

IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE,

DO NOT OPERATE THE TOOL!

Grounding Instructions

This machine has a three-prong plug, the third prong is the ground. Plug this cord

only into a three-prong receptacle. Do not attempt to defeat the protection the ground wire

provides by cutting off the round prong. Cutting off the ground will result in a safety hazard

and void the warranty.

DO NOT MODIFY THE PLUG IN ANY WAY. IF YOU HAVE ANY DOUBT, CALL A

QUALIFIED ELECTRICIAN.

Specification：

Max. drilling capacity: 20 mm

Max. tapping capacity: 12 mm

End mill capacity 16 mm

Face mill capacity 50 mm

Throat 190 mm

Max. distance spindle to table 370 mm

Spindle taper MK#3

Spindle speed 100-2500 rpm ±10%

Table effective size 600x140 mm

T-slot size 12 mm

Table longitudinal travel (X) 400 mm

Cross travel (Y) 190 mm

Headstock travel (Z) 290 mm

Power 750 W

Overall dimension (L*W*H) 725*620*880 mm

Packing size (L*W*H) 840*760*1060 mm

Weight (Net/Gross) 101 / 135 Kg

Unpacking & Preparing for Use

Before unpacking you must check the package carefully, to find whether it is damaged

and any may have effect on the machine, please connect with the distributor in advance.

Unpacking carefully, check the species of standard accessories and the quantity to find

whether it is as same as the packing list in the package.

FEATURE

1 Base 2 Cross feed handwheel

3 Long worktable 4 Fuselage (with protect cover)

5 Drill chuck with arbor 6 Protective dust guard assembly

7 Spindle sleeve locking handle 8 Micro switch assembly

9 Depth display 10 Touch switch panel

11 Electric control box 12 Speed display

13 Emergency stop switch 14 Spindle box cover

15 Fine feeding handle 16 Spindle box

17 Vertical feed handwheel 18 Fuselage back cover

19 Fine feeding locking handle 20 Spindle control handle assembly

with tapping button

21 Power socket with fuse box 22 Longitudinal feed handwheel

23 Saddle locking handle 24 Worktable locking handle

Installation CAUTION!

DO NOT ATTEMPT TO USE THE MACHINE UNTIL INSTALLTION IS CAMPLETED,

AND ALL PRELIMINARY CHECKS HAVE BEEN MADE IN ACCORDANCE WITH THIS

MANUAL.

MOUNTING THE MACHINE

The machine should be mounted on a strong, heavy workbench, of sufficient height so

that you do not need to bend your back to perform normal operations.

Ensure the location is adequately lit and that you will not be working in your own shadow.

We strongly recommend that the machine bolted firmly to strong workbench using the

tapped holes used to secure the feet to the machine. This is to provide added stability and

consequently, additional safety.

To do this, first drill four M12 clearance holes in a worktop, at the dimensions

shown in the diagram opposite, and with appropriate length M10 bolts, or screws,

with flat washers. (not supply, you need prepare these by yourself).

Application

This small mill machine is both for milling or drilling and tapping, widely used in different

places. Fine exterior, wide range of speed and easy to use.

Designed for industrial usage milling, drilling, tapping, reaming, steps and mill plane with

metal and other material.

305

210

Operation

1. Before starts to use this machine, operator should go through the instructions carefully

so as to acquaint with the construction of the machines, the functions of the various

controls and also the driving systems.

2. This machine uses touching button (see operation panel below), operating steps refer

to the flow chart.

Spindle speed readout

Operation panel Spindle depth readout

Operating steps

1. Insert the electric plug into its socket. Then release the emergency stop switch by

turning the red round head of the switch. you can see the spindle speed readout will

bright, it means power on.

2. Press ‘Start’ button (the green and oval button is “I”) on the touching panel, spindle

speed readout shows ‘0100 FORWARD’. These showing on the display’s right side.

Notice:‘0100’ is the lowest speed of this machine.

3. You can choose press the ‘ ’ button or ‘ ’ button, if press the ‘‘ button the spindle

will rotate “Forward”, if press the ‘‘ button the spindle will rotate “Reverse”.

4. Press the ‘+’ button the spindle speed will quicken, you have two choice: one is single

click then the speed rise 10 rpm one click, the other is press the “+” button not loosen

then the speed will rise quickly, the highest speed is 2000 rpm. Also you can press the

“-” button the spindle speed will slowly, you also have two choice the control method as

same as press the “+” button.

5. Press ‘Stop” button (the red and oval button is “0”), spindle will stop running, if press

‘Start’ button now, spindle runs to the speed last setting automatically. When you

operate the mill machine encounter emergency you can press the “Emgency stop

switch” the machine will power off.

6. Press the “Tapping” button ( drawing is a screw tap, the position up the “+” button), the

light above the ‘Tapping’ button lights. This means now is the ‘Tapping mode’, ‘Forward’

and ‘Reverse’ buttons are unavailable.

7. Tapping: the highest speed under ‘Tapping mode’ is 500rpm.

Press the button end of the handle the first is “forward” when

press again it change to “reverse”. Notice it have three handle all

can control so it is very easy to do.

See the picture on the right position.

8. Fine feeding function: When lock the Lock small handwheel (A), then the control handle

(B) can not useable. Turn the fine feeding handwheel (C) the spindle will micro remove.

Notice:

After using should turn the power switch to position ‘0’ and pull out the plug from

socket.

Parts drawing ( 1 / MT3 ) --the spindle taper is MT3

Parts list ( 1 / MT3 ) --the spindle taper is MT3

Part No. Drawing No. Description Q'ty

.1-1 XN3B0206 Spindle box 1

.1-2 GB 818-85 - M4 x 6 Cross recessed small pan head screw H type M4*6 2

.1-3 X3C0219 Spindle below oil seal ring I 1

.1-4 X20206 B16 taper shank 1

.1-5 GB/T 297-94 - 32907 Cone roller bearing 32907 1

.1-6 GB 6172-86 - M5 Hexagon headed nut M5 2

.1-7 XN3A0218 Fine feeding handwheel 1

.1-8 X3C0217 Display fixed square screw 1

.1-9 X3C0216 Spindle sleeve below oil seal ring II 1

.1-10 GB 818-85 - M3 x 8 Cross recessed small pan head screw Z type M3*8 12

.1-11 XN3A0215 Base plate 1

.1-12 GD300-165 The digital display module 1

.1-13 XN3A0207 Panel 1

.1-14 X3C0210 Up washer II 1

.1-15 GB 819-85 - M5x20 Cross recessed counter head screws M5*20 1

.1-16 XN3A0210 Bevel gear 1

.1-17 XN3A0204 Gear shaft 1

.1-18 16-16 Check ring 16 1

.1-19 XN20243 Clock spring 1

.1-20 X3C0253 Clock spring cover 1

.1-21 XN3A0205 Spindle box cover 1

.1-22 X3C0208 Bear seat 1

.1-23 X3C0206 Spindle timing belt 1

.1-24 X2021800 Small handle assembly 1

.1-25 XN3A0208 Spindle sleeve locking shaft 1

.1-26 XN3A0217 Tighten the top rod 1

.1-27 GB 79-85 - M6 x 14 Slotted headless set screws M6*8 1

.1-28 GB 77-85 - M6 x 8 Inner six angle locking screws flat head M6*14 1

.1-29 GB308-89 - 8 Ball 8 3

.1-30 XN3A0224 Locking small shaft 1

.1-31 X3C0238 Worm locking handle 1

.1-32 X3C0213 Spindle sleeve 1

.1-33 X3C0252 Sshaft gear left support flange 1

.1-34 GB 77-85 - M6 x 10 Inner six angle locking screw flat head M6*10 1

.1-35 GB1096-79 4x8 Pin 1

.1-36 X3C0220 Spindle up dust guard I 1

.1-37 X3C0265 Spindle up dust guard II 1

.1-38 GB 70-85 - M4 x 10 Hexagon socket head cap screw M4*10 3

.1-39 XN3A0216 Eccentric sleeve locking block 1

.1-40 7_70 - 12 x 22 x 5 Thrust ball bearing single 12*22*5 2

.1-41 XN3A0209 Worm shaft 1

.1-42 XN3A0203 Worm eccentric sleeve 1

.1-43 X3C021100 Locking bolt assembly 1

Parts list ( 1 / MT3 ) --the spindle taper is MT3

Part No. Drawing No. Description Q'ty

.1-44 GB 119-86 - A 3 x 10 Round pin A 3*10 1

.1-45 GB 301-84 - 8106 Thrust ball bearing 8106 1

.1-46 GB 278-89 - 80106 Deep groove ball bearing 80106 1

.1-47 X3C0209 Up washer 1

.1-48 GB 810-76 Slotted round nut 2

.1-49 GB 70-85 - M4 x 12 Hexagon socket head cap screw M4*12 6

.1-50 GB 278-89 - 80107 Deep groove ball bearing 80107 1

.1-51 GB 893.1 - 62 Check ring 62 1

.1-52 GB 894.1 - 35 Check ring 35 1

.1-53 GB 70-85 - M5 x 16 Hexagon socket head cap screw M5*16 4

.1-54 X3C0212 Spindle 1

.1-55 HTD-M5 385（77 齿） Timing belt Z77 1

.1-56 GB 97.1-85 - 6 Washer 6 4

.1-57 GB 70-85 - M6 x 14 Hexagon socket head cap screw M6*14 4

.1-58 GB 879-86 - 3 x 8 Spring round pin 3*8 2

.1-59 X3C0237 Assist small handle 1

.1-60 GB 119-86 - A 3 x 14 Round pin A 3*14 1

.1-61 GB 819-85 - M3x10 Cross recessed counter head screws H type M3*10 5

.1-62 XN3B0205 Washer 1

.1-63 XN3A0213 Spindle sleeve position shaft 1

.1-64 20-20 Check ring 20 2

.1-65 XN3A0214 Display fixed bracket 1

.1-66 XN3A0222 Round gear shaft adjust washer 1

.1-67 GB 70-85 - M10 x 16 Hexagon socket head cap screw M10*16 1

.1-68 XN3A0202 Bevel wedge 1

.1-69 XN3A0223 Wedge screw 2

.1-70 XN3A0226 Sleeve limted washer 1

.1-71 XN3A0211 Atachment bracket 1

.1-72 GB 5781-86 - M5x12 Hexagon headed bolt M5*12 3

.1-73 XN3B0203 Motor support plate 1

.1-74 XN3B0201 Motor timing pulley 1

.1-75 GB 896-86 3 Spring washer 3 3

.1-76 XN3B0202 Handle seat 1

.1-77 XN3B0204 Shaft gear right support flange 1

.1-78 GF300220 Conducting ring assembly 1

.1-79 GB 70-85 - M5 x 12 Hexagon socket head cap screw M5*12 4

.1-80 W80-750W 750W brushless DC motor 1

.1-81 GB2089-80 0.8x6x25 Compress spring 0.8*6*25 3

.1-82 GB1096-79 4x25 Parallet key 4*25 1

.1-83 GB 70-85 M4 x 40 Hexagon socket head cap screw M4*35 4

.1-84 XN3B020700 Ccontrol pole assembly 3

.1-85 XN3B020800 F/R control pole assembly 3

.1-86 GB 818-85 - M3 x 4 Cross recessed small pan head screw Z type M3*4 1

.1-87 YE023005 Ø4x2 Magnet 1

Parts drawing ( 2 / R8 ) --the spindle taper is R8.

Parts list ( 2 / R8 ) --the spindle taper is R8.

Part No. Drawing No. Description Q'ty

.2-1 XN3B0206 spindle box 1

.2-2 X3C02A02 R8 spindle sleeve 1

.2-3 X3C02A01 R8 spindle 1

.2-4 XN3A0215 base plate 1

.2-5 XN3A0204 gaar shaft 1

.2-6 XN3A0210 bevel gear 1

.2-7 XN3B0204 shaft gear right support flange 1

.2-8 XN3B0202 handle seat 1

.2-9 XN3A0205 spindle box cover 1

.2-10 GB 70-85 - M4 x 10 hexagon socket head cap screw M4*10 9

.2-11 X3C0252 shaft gear left support flange 1

.2-12 XN20243 clock spring 1

.2-13 X3C0253 clock spring cover 1

.2-14 GB2089-80 0.8x6x25 compress spring 0.8*6*25 3

.2-15 XN3A0218 fine feeding handwheel 1

.2-16 X3C0217 display fixed square screw 1

.2-17 GB 818-85 - M3 x 8 cross recessed small pan head screw Z type M3*8 12

.2-18 GB 6172-86 - M5 hexagon headed nut M5 2

.2-19 XN3A0202 bevel wedge 1

.2-20 X2021800 small handle assembly 1

.2-21 XN3A0207 panel 1

.2-22 XN3A0208 spindle sleeve locking shaft 1

.2-23 GB 894.1 - 20 check ring 20 2

.2-24 GB 894.1-86 16 check ring 16 1

.2-25 X3C0238 worm locking handle 1

.2-26 GB1096-79 4x8 parallet key 4*8 1

.2-27 X302A04 JT6 taper shank 1

.2-28 GD300-165 display assembly 1

.2-29 XN3B0203 motor support plate 1

.2-30 X3C0219 spindle below oil seal ring I 1

.2-31 X3C0216 spindle sleeve below oil seal ring II 1

.2-32 GB/T 297-94 - 32907 cone roller bearing 32907 1

.2-33 X3C02A03 shoulder cylindrical key 1

.2-34 GB 301-84 - 8106 thrust ball bearing 8106 1

.2-35 X3C0210 up washer II 1

.2-36 GB 278-89 - 80106 deep groove ball bearing 80106 1

.2-37 GB 810-76 slotted round nut 2

.2-38 X3C0209 up washer 1

.2-39 GB 79-85 - M6 x 14 slotted headless set screw round end M6*14 1

.2-40 GB 77-85 - M6 x 8 inner six angle locking screw flat head M6*8 1

.2-41 GB 77-85 - M6 x 10 inner six angle locking screw flat head M6*10 1

.2-42 GF300220 conducting ring assembly 1

.2-43 X3C0208 bearing seat 1

Part No. Drawing No. Description Q'ty

.2-44 GB 278-89 - 80107 deep groove ball bearing 80107 1

.2-45 GB 893.1 - 62 check ring 62 1

.2-46 GB 894.1 - 35 check ring 35 1

.2-47 GB 70-85 - M5 x 16 hexagon socket head cap screw M5*16 4

.2-48 X3C0206 spindle timing pulley 1

.2-49 X3C0220 spindle up dust guard I 1

.2-50 X3C021100 locking bolt assembly 1

.2-51 X3C0265 spindle up dust guard II 1

.2-52 XN3B0201 motor timing pulley 1

.2-53 GB273.2-87 - 12 x 22 x

5 thrust ball bearing 12*22*5 2

.2-54 XN3A0203 worm eccentric sleeve 1

.2-55 XN3A0209 worm shaft 1

.2-56 HTD-5M 385（77 齿） timing belt 1

.2-57 GB 119-86 - A 3 x 10 round pin A 3*10 1

.2-58 GB 819-85 - M5x20 cross recessed counter head screws M5*20 1

.2-59 GB 97.1-85 - 6 washer 4

.2-60 GB 70-85 - M6 x 14 hexagon socket head cap screw M6*14 4

.2-61 GB 879-86 - 3 x 8 spring round pin 3*8 1

.2-62 GB 818-85 - M4 x 6 cross recessed small pan head screw H type M4*6 2

.2-63 XN3A0224 locking small shaft 1

.2-64 GB308-89 - 8 ball 8 3

.2-65 GB 896-86 3 spring washer 3

.2-66 GB 119-86 - A 3 x 14 round pin A 3*14 1

.2-67 X3C0237 assist amll handle 1

.2-68 XN3A0211 attachment bracket 1

.2-69 GB 5781-86 - M5x12 hexagon headed bolt M5*12 3

.2-70 GB 819-85 - M3x10 cross recessed counter head screws M3*10 5

.2-71 XN3A0214 display fixed support 1

.2-72 XN3A0216 eccentric sleeve locking block 1

.2-73 XN3B0205 washer 1

.2-74 XN3A0213 spindle sleeve position shaft 1

.2-75 XN3A0222 round gear shaft adjust washer 1

.2-76 XN3A0223 wedge screw 2

.2-77 GB 70-85 - M10 x 16 hexagon socket head cap screw M10*16 1

.2-78 XN3A0226 sleeve limted washer 1

.2-79 W80-750W 750 brushless DC motor 1

.2-80 XN3A0217 tighten the top rod 1

.2-81 GB 70-85 - M5 x 12 hexagon socket head cap screw M5*12 4

.2-82 GB1096-79 4x25 parallet key 4*25 1

.2-83 GB 70-85 M4 x 40 hexagon socket head cap screw M4*40 4

.2-84 GB 818-85 - M3 x 4 cross recessed small pan head screw H type M3*4 1

.2-85 XN3B020700 control handle assembly 3

.2-86 XN3B020800 F/R control pole assembly 3

.2-87 YE023005 Φ4x2 magnet 1

Parts drawing ( 3 )

Parts list (3) --- note: The no. With “*” means the part showing in metric.

Part No. Drawing No. Description Q'ty

.3-1 XN3A0901 Column 1

.3-2* XN3A0903A Metric rise and down leadscrew 1

.3-3* XN3A0908A Metric rise and down locking nut 1

.3-4* XN3A0907A Metric rise and down leadscrew nut 1

.3-5 XN3A0904 Column nut support 1

.3-6 XN3A0911 Leadscrew support 1

.3-7 GB 118-86 - 6 x 16 Taper pins with internal thread 6*16 2

.3-8 GB 70-85 - M6 x 12 Hexagon socket head cap screw M6*12 2

.3-9 XN3A0910 Rise and down support seat 1

.3-10 C2A0307 Handle 1

.3-11 GB 6172-86 M8 Hex nut M8 1

.3-12 X3111800 Handle wheel 1

.3-13 X31145 Spring piece 1

.3-14* XN3A0909A Metric rise and down scale dial 1

.3-15 GB 879-86 - 3 x 20 Spring round pin 3*20 1

.3-16 GB/T 276-94 - 6001 Deep groove ball bearing 6001 4

.3-17 GB 65-85x55 Slotted large cheese head screws 85*55 1

.3-18 GB 889-86 M8 Hex locking nut M8 1

.3-19 GB1096-79 4x16 Parallet key 4*16 1

.3-20 XN3A0902 Rise and down shaft 1

.3-21 GB 879-86 - 3 x 16 Spring round pin 3*16 1

.3-22 GB 70-85 - M5 x 30 Hexagon socket head cap screw M5*20 4

.3-23 GB 5781-86 - M5x16 Hexagon headed bolt M5*16 3

.3-24 GB 77-85 - M6 x 10 Inner six angle locking screws-flast end M6*10 1

.3-25 XN3A0912 Locking nut 4

.3-26 XN3A0914 Big bevel gear wheel 1

.3-27 XN3A0913 Small bevel gear wheel 1

.3-28 GB 78-85 - M5 x 8 Inner six angle locking screws-cone end M5*8 1

.3-29 GB 78-85 - M5 x 5 Inner six angle locking screws-cone end M5*5 1

.3-30 GB 5780-86 - M10x40 Hexagon headed bolt M10*40 4

.3-31 GB 97.1-85 - 10 Washer 10 4

.3-32 GB 859-87 - 10 Spring washer 10 4

.3-33 GB 118-86 - 6 x 24 Taper pins with internal thread 6*24 2

.3-34 GB 97.1-85 - 8 Washer 8 1

.3-35 GB 70-85 - M8 x 30 Hexagon socket head cap screw M8*30 2

Parts drawing( 4 )

Parts list (4) --- note: The no. With “*” means the part showing in metric.

Part No. Drawing No. Description Q'ty

.4-1 X31136 The left bracket cover 1

.4-2 XN3A1106 Left cover 1

.4-3 X31131 Longitudinal leadscrew rod bracket left sleeve 1

.4-4 XN3A1102 Work table 1

.4-5* XN3A1113A Metric longitudinal leadscrew nut 1

.4-6 XN3A1103 Saddle 1

.4-7 XN3A1101 Base 1

.4-8 X3111800 Handwheel 2

.4-9 XN3A1105 Cross bevel wedge 1

.4-10 XN3A1109 Longitudinal wedge locking crown bar 1

.4-11 X2021800 Small handle assembly 2

.4-12* XN3A1110A Metric longjitudinal leadscrew 1

.4-13 XN3A1108 Longitudinal\cross leadscrew bearing seat 2

.4-14* XN3A1112A Metric longitudinal/cross scale dial 2

.4-15 GB 6172-86 M8 Hexagon nut M8 2

.4-16 GB 70-85 - M5 x 14 Hexagon socket head cap screw M5*14 2

.4-17 X31144 Plug 1

.4-18 GB 70-85 - M6 x 16 Hexagon socket head cap screw M6*16 6

.4-19 GB1096-79 4x16 Parallet key 4*16 2

.4-20 GB 889-86 M8 Hexagon locking nut M8 2

.4-21 GB 65-85x55 Slotted large cheese head screws 85*55 2

.4-22 X31145 Sping piece 2

.4-23 GB 301-84 - 8101 Thrust ball bearing 8101 4

.4-24 XN3A1111 Longjitudinal bevel wedge 1

.4-25 XN3A1107A Metric cross leadscrew nut 1

.4-26* XN3A1104A Metric cross leadscrew 1

.4-27 GB 70-85 - M5 x 20 Hexagon socket head cap screw M5*20 2

.4-28 C2A0307 Handle 2

.4-29 XN3A0217 Tighten the top rod 1

.4-30 JBT7940.4-95 6 Pressure with pressure column oil cup 6 1

.4-31 GB 70-85 - M4 x 14 Hexagon socket head cap screw M4*14 4

.4-32 XN3A0223 Wedge screw 4

.4-33 GB 119-86 - A 4 x 20 Round pin A4*20 6

.4-34 XN3A1114 Scale height 1

.4-35 GB827-86 2x3 Label rivet 2*3 4

.4-36 C5C0315 Zero lebel 1

.4-37 GB 97.1-85 - 8 Washer 8 2

4-38 GB 117-86 - A 3 x 30 Taper pin A3*30 2

4-39 GB 70-85 - M6 x 10 Hexagon socket head cap screw M6*10 1

4-40 GB 96-85 - 6 Washer 6 1

4-41 GB 117-86 - B 3 x 26 Taper pin B3*26 2

Parts drawing( 5 )

Parts list (5) (Note: some type without the protective guard assembled)

Part No. Drawing No. Description Q'ty

.5-1 XN3A2305 Splash guard I 1

.5-2 XN3A2304 Splash guard II 1

.5-3 X20002 Filler strip 1

.5-4 GB 818-85 - M4*6 Cross recessed counter head screws M5*6 6

.5-5 X20003 Dust guard 1

.5-6 X20004 Dead plate 1

.5-7 GB 818-85 - M4*10 Cross recessed counter head screws M4*10 2

.5-8 XN3A2302 Rise and down guideway cover 1

.5-9 YE023003 Ø6 Magnet steel 5

.5-10 XN3A2303 Shield baffle 1

.5-11 GB 819-85 - M4x10 Cross recessed counter head screws M4*10 3

.5-12 X3C23C0401 The inner shield 1

.5-13 GB 835-88 - M5x20 Knurled screws M5*20 2

.5-14 GB 97.1-85 - 5 Washer 5 2

.5-15 X3C23C03 Outer protective cover 1

.5-16 GB 70-85 - M4 x 10 Hexagon socket head cap screw M4*10 1

.5-17 X12304 Block 1

.5-18 XN3A2301 Connecting plate 1

.5-19 QKS7-5 Safety limit switch 1

.5-20 GB 889-86 - M6 Hexagon locking nut M6 1

.5-21 GB 96-85 - 6 Washer 6 1

.5-22 X3C23C01 Support plate 1

.5-23 GB 70-85 - M4 x 12 Hexagon socket head cap screw M4*12 3

.5-24 X3C23C05 Spacer bush 1

.5-25 GB 818-85 - M4 x 25 Cross recessed counter head screws M4*25 2

.5-26 GB 78-85 - M4 x 6 Inner six angle locking screw-cone end metric M4*6 1

.5-27 X3C23C02 Rotate shaft 1

Parts drawing( 6 )

Other manuals for FP-20A

Table of contents

Other Proma Power Tools manuals

Proma

Proma FP-20A User manual

Popular Power Tools manuals by other brands

Grizzly

Grizzly G1024 instruction manual

Makita

Makita HM0810B Parts Breakdown

Clarke

Clarke CAT126 Operating & maintenance instructions

Bosch

Bosch GKS18V-25C Operating/safety instructions

BBB

BBB BTL-73 manual

Kobalt

Kobalt KL12120 operating instructions

Southwire

Southwire SCR6-B Operator's manual

Makita

Makita DSC162 instruction manual

Sealey

Sealey Siegen Tools S01047 manual

Draper

Draper StormForce PT141KSF instructions

Makita

Makita GN900 instruction manual

Metabo

Metabo MFE 30 Original instructions

Holzstar

Holzstar FKS 315-1500 E instruction manual

Progress Direct Systems

Progress Direct Systems Volt Tattler 2 owner's manual

Makita

Makita JN1601 instruction manual

LOBSTER

LOBSTER BN200 instruction manual

S.E.F.A

S.E.F.A SUBLIMAX 1812 instruction manual

Kamikaze

Kamikaze KV 300 user manual