Promag ER750 User manual

Ethernet Reader ER750/ER755
Quick Start

1
TM970166A
Ethernet Reader Quick Start
Connect Reader to Ethernet Network
Step 1
Connect the ER750/ER755
reader to an Ethernet hub via
the Ethernet cable.
Note:
Or you can connect the
ER750/ER755 reader to your
PC/Laptop directly by one
Ethernet cable.
Step 2
Connect the power (DC12V) to
the pin VCC and GND.
Note:
Or you can connect an
ER750-10/ER755-10 reader to
your P.O.E HUB
Connect Reader to Ethernet Network
+
-
DC12V

2
TM970166A
Ethernet Reader Quick Start
Step 3
Use “EthernetReaderDiscover”
software to search all of our
available Ethernet devices on
network.
(This software can be found in
the installation CD “disk5453”).
Step 4.
Click “Refresh”to refresh the
Ethernet reader list.
Step 5. (Optional)
Click “IP Settings”to change
the new device name on
network.
Connect Reader to Ethernet Network

3
TM970166A
Ethernet Reader Quick Start
Step 6. (Optional)
Edit the ER750/ER755 device
name for easy recognition.
Click "Save" to update settings.
NOTICE:
If you have to manually set IP
address, you can click "Manual"
and then setup IP address of the
device.
Connect Reader to the Ethernet Network

4
TM970166A
Ethernet Reader Quick Start
Configure ER750/ER755 Reader Settings
Step 1
Run “EthernetReaderDiscover”software
to search all available Ethernet devices on
network.
Select your device, and then click “Reader
Utility”.
Remark:
“”–means the communication successfully by the IP address
and the device name.
“! ”–means the communication by the IP address.
“X”–means the communication fail.
Step 2
The “Ethernet Reader Discover”utility will
execute the “Mifare/DESfire Reader
Utility”and connect to the selected reader.
< ER750 >
Remark:
For ER750, the “Read Mode”fixed to “CSN Only”.
Configure ER750/ER755 Reader Settings

5
TM970166A
Ethernet Reader Quick Start
< ER755>
Remark:
For ER755, the “Read Mode”can be switch to:
“CSN Only”/ “Card Data Only”/ “Card Data or CSN (when card error)”
Remark:
For the “Read Mode”is “Card Data Only”, you have to enter the card’s app key
or offset & length for used card in the “Mifare”pane as below picture:
Configure ER750/ER755 Reader Settings

6
TM970166A
Ethernet Reader Quick Start
Step 3
Configure the LED/buzzer appearance.
< ER750>
<ER755>
Configure ER750/ER755 Reader Settings

7
TM970166A
Ethernet Reader Quick Start
Remark:
If you have to control hardware by commands, please check “Enable
LED/Buzzer Command Set Conatrol”before update configures.
Configure ER750/ER755 Reader Settings

8
TM970166A
Ethernet Reader Quick Start
Step 4
Then setup device settings and IP
settings.
Remark:
type in same settings as Event Server software
(both of the IP Address and the Port Number).
Step 5
Begin to receive the event from the device.
We open the Event Server source code in
VB language, and hope that can help you
easily to integrate Event Server into your
system.
Configure ER750/ER755 Reader Settings

9
TM970166A
Ethernet Reader Quick Start
How to change PC/Laptop network setting to support the Auto IP mode
Step 1
Most of the PC/Laptop network default setting
is “Obtain an IP address automatically”(auto
IP mode). If not, you can follow the steps to
change the network setting to auto IP mode.
Go to:
Control Panel > Network and Internet Connections
>
Local Area Connection Properties
Step 2
General select Internet Protocol (TCP/IP) and click
Properties.
Step 3
Select the “Obtain an IP address automatically.
Then click “OK”.
Trouble Shooting –Set to Auto IP Mode

10
TM970166A
Ethernet Reader Quick Start
Step 4
Connect the ER750/ER755 reader to PC/Laptop via
Ethernet cable then power on the ER750/ER755
reader.
Trouble Shooting –Set to Auto IP Mode

11
TM970166A
Ethernet Reader Quick Start
The ER750 does not supplying power for the electronic lock, so please reference below pictures to connect the lock.
Load means the lock. Connects VIN to power, GND to common, and the power supply’s ground connect to NO
(Normally Open).
The ER750 wire assignment please references the document: “ER750 Series Wires Assignment.pdf”.
Wire Connect to the Door Lock Suggestion

12
TM970166A
Ethernet Reader Quick Start
If you have the requirement about issue user card immediately, we have the Mifare/DESFire Card Issuer software to
help you that issue the user card easily and quickly, and you should have a “PCR310 R/W device”for issue cards,
please contact the sales for more information.
Issue Card Software

13
TM970166A
Ethernet Reader Quick Start
Installation Manual

14
TM970166A
Ethernet Reader Quick Start
CAUTION:
The crossed out wheeled bin label that can be found on your
product indicates that this product should not be disposed of
via the normal household waste stream.
To prevent possible harm to the environment or human
health please separate this product from other waste
streams to en-sure that it can be recycled in an
environmentally sound manner.
For more details on available collection facilities please
contact your local government office or the retailer where
you purchased this product.
This information only applies to customers in the European
Union.
For other countries, please contact your local government
to investigate the possibility of recycling your product.
PROMAG®
GIGA-TMS INC.
http://www.gigatms.com.tw
mailto:[e-mail]
TEL : [phone]
FAX : [phone]
Office: 8F, No. 31,Lane 169, Kang-Ning St.,Hsi-Chih, Taipei, Taiwan
TM951128