Proscenic BM300 User manual

BM300 HD Video Baby Monitor
User's manual

Packing List
Product overview
Getting Started
Installation Step
Function overview
Cameras
Feeding
Sound Alarm
Temp.Alarm
Music
Display
Recording
Playback
System
About
FAQ
1
2-4
5
6
7
8-9
10
11-12
13
14
15
16
17-18
19
20
21
EN

Safety Cautions
Packing List
1. Keep the cord(s) away from children in case of strangulation (3 feet/1
meter away).
2. Put the product(s) in a dry place in case of short-circuit.
3. Use the Power Adapter(s)provided by us ONLY. Using unauthorized charging
cables and Power Adapters may result in overheat even explosion.
4. Unplug the Power Adapter(s) if you don't use it(them).
5. Check your baby's activities regularly as this product is not designed for
supervision but for assisting your supervising.
Incorrect operation of the product(s) may lead to safety risks. Therefore, we
STRONGLY recommend you read the instructions carefully before the first use.
Monitor x1
Type-C Cable x1
(For Monitor)
Micro USB Cable x1
(For Camera)
Camera x1
Screw Set x1 USER MANUAL
5V Power Adapter x2
Bracket x1
1
EN
BM300 HD Video Baby Monitor
User's manual

Product overview
Tip:
Incorrect operation of the product(s) may lead to safety risks. Therefore,
we STRONGLY recommend you read the instructions carefully before the
first use.
Camera
2
EN

1. Screen: Before the first use, please remove the protective film on the screen.
2. Power/Sleep Button: Long press to power on/off the monitor; short press
to turn on/off the screen.
3. VOX: When you watch the live video, press it to turn on/off the sound detection.
4. Power Indicator: It is green when the battery is fully charged, and will turn
red when the battery is low.
5. Back/Menu: Press it to enter menu page or as a back button.
6. Camera Switch: To switch among cameras or loop the live video if 2 or
more cameras are connected with the monitor.
7. Up: Press it to tilt the camera upward or to change your selection upward.
8. Left: Press it to pan the camera leftward or to change your selection leftward.
9. Right: Press it to pan the camera rightward or to change your selection rightward.
10. OK: confirm your selection.
3
EN

11. Down: Press it to tilt the camera downward or to change your selection
downward.
12. Volume/Brightness: Press it to bring up the Volume/Brightness,then press
Left/Right/Up/Down to adjust the monitor's volume or brightness.
13. Talk: Press and hold it to talk with your baby near the camera.
14. Microphone
15. Memory Card Slot
16. Antenna
17. Speaker
18. Stand
19. Type-C Port
4
EN

Getting Started
Notes:
1. Generally,the camera has been paired with the monitor already. If it is
not paired, please refer to the next section to pair it manually.
2. Install a memory card to the monitor or camera before you power on it
if you would like to record videos.
3. After powering on your monitor, please set time & date firstly.
4. The monitor will not power on or will display abnormalities if its power
is too low. Please try again after 10 minutes of charging.
Step 1:
Charge the monitor by connecting the Power Adapter to the monitor and a
socket. It takes about 4 hours for the monitor to be fully charged, and the
battery lasts about 8 hours.
Step 2:
Connect the power adapter to the camera and use the socket to power
the camera.The camera beeps when powered on.
Step 3:
Place the camera at least 3ft/lm away from your baby.
Step 4:
Gently press and hold the Power Button for 3s to turn on the monitor,then you
can see the live view.
5
EN

4. Align the grooves with the mounting plate and rotate the Camera clockwise
until it clicks into place.
Installation Step
XX
1. Place the bracket against the ceiling
and then mark the points at which
drilling will be required.
2. Drill holes with a 5/16 ”(8 mm)
drill bit.
3. Align the holes on the mounting plate with those in the
ceiling. Insert the anchors into the holes; anchors are
necessary for walls that are made out of hard materials
Phillips-head screwdriver to fasten the mounting plate
to the ceiling.
such as concrete, brick, or stucco. Fix the screws with a
6
EN

4. Sound
7
EN
Function overview
Monitoring Interface
1. Signal
2. Battery Power Status
3. Temperature
5. Feeding Reminder Enabled
6. Music Enabled
7. Sound Detection: it will turn up if you
enable VOX function.
8. Live Video Loop Enabled
9. Camera Channel
10. Date and Time
Other icons will be displayed on the monitoring interface when an alarm or
notication for abnormality is issued.
No signal Temperature alarm
Feeding reminder
Low battery
Sound alarm

Tip:
A grey icon indicates that no camera is paired with this channel, while a
green icon indicates that a camera has been paired with this channel.
Step 1: Press to enter the menu page and select Cameras.
Step 2: Select an unpaired channel (e.g. Channel 2) and press OK, the
monitor will start searching for a camera.
8
EN
Cameras
1. Pair a New Camera with the Monitor

Tip:
1. If the pairing fails,you will see the prompt Pairing failed on the screen.
Please repeat the steps above and try to pair again.
2. Four cameras at most can be paired with one monitor.
3. If you reset the camera, it is recommended to pair with the first channel,
not with channels 2, 3 and 4, otherwise the pairing will fail.
Step 3: Keep the camera on and it will automatically pair with the monitor.
After success, you will see the prompt: Paired
If you would like to replace the old camera, just pair a new camera with the
same channel which the old camera is previously paired with.The old camera
will be deleted once the pairing is successful.
2. Replace the Old Camera
9
EN

Step 1: Select Feeding on the menu page.
Step 2: Set the Time Interval and Repeat Mode; press OK to confirm.
When you set the time interval as 2.5H, if you select "Once", the alarm will be
triggered only once in 2.5 hours;if select "Always", the alarm will be triggered
every 2.5 hours.
10
EN
Feeding
This function aims to remind you of feeding your baby

Tip:
The monitor will beep and display an icon when it is the feeding time.
Press any button to stop the alarm.
11
EN
Sound Alarm
This monitor has a voice operated switch, also knownas VOX. It will send
alarms when the sound over a certain threshold is detected.
Step 1: Select Sound Alarm on the menu page.
Step 2: Select the sensitivity level and press OK to confirm.

There are four options to adjust the sensitivity of sound detection:
OFF, LOW, MEDIUM and HIGH.
OFF means to disable sound detection. If you set the sensetivity to LOW, you
will receive alarms only when your baby is crying loudly; if MEDIUM, you will
receive alarm swhen your baby's voice is loud; if High, you will receive alarms
just when your baby speaks normally.
12
EN
Tip:
When the alarm is triggered, the monitor will screen on with an icon and
make a sound alarm.
Press any button to stop the sound alarm. or you can press VOX button to
turn off this function.

Tip:
When the alarm is triggered, the monitor will screen on with an icon
and make a sound alarm.
Press any button to stop the sound alarm.
13
EN
Temp.Alarm
The monitor will send alarms when the ambient temperature is too low(<18
℃/64°F)or too high(>30°C/86°F).
Step 1: Select Temp.Alarm on the menu page.
Step 2: Enable the Temp. Alarm and select the Temp. Unit; press OK to confirm.

Music
This function is to comfort your baby when needed. The volume and type of
each song are distinctive, please select the best one for your baby.
Step 1: Select Music on the menu page.
Step 2: Select a song and set the playing mode; press OK to confirm.
If you select one song, the song will be played repeatedly; if select Loop Play,
four songs in the same category will be played in a loop.
14
EN

15
EN
Step 1: Select Display on the menu page.
Step 2: Set the sleep time and press OK to confirm.
If you select 1 Min, your monitor will enter sleep mode in 1 minute if there is
no any operation; the same for 10 Min and 30 Min.
Display
This function is to prolong your monitor's runtime by shutting down the
screen.

Recording
This function is to record videos for your baby. The maximum video length is 1
hour by default.
Step 1: Select Recording on the menu page.
Step 2: Enable it to record videos to the monitor or camera according to the
memory card installation; press OK to confirm.
16
EN

Tips:
After installed, your memory card will be formatted once you power on
the monitor or camera.
Please set the date and time before you enable the function of recording
videos so that you can search precisely for video playback.
Playback
Step 1: Select Playback on the menu page, it will play the latest recorded
videos on channel 1 by default. If there are no videos on channel 1, please
select to check more.
Step 2: After you select and press OK, it will pop up a search page. Set date,
time and channel, then select Search and press OK to filter out your desired
videos.
17
EN

Tip:
The resolution of videos recorded to the monitor is 480P; while the
resolution of videos recorded to the camera is 1080P.
Videos recorded in the monitor can only be watched through your
monitor, and cannot be read via a computer. If you would like to watch
videos recorded in the camera, please remove the card and watch videos
on your computer via a card reader.
18
EN