Proseries St1033 Operator's manual

pecifications 1/3 HP Model T1033 1/2 HP Model T1050

GP @ 0’ 4100 5300

GP @ 10’ 2770 3630

Pump diameter 7.375” 9.75”

Volts 115V, 60 z 115V, 60 z

Amps 3.8 4.8

Important afety Instructions

AVE THE E IN TRUCTION . This manual contains important SAFETY WARNINGS and

OPERATING INSTRUCTIONS for the Pro Series pumps. You will need to refer to it before

attempting any installation or maintenance.

ALWAY keep these instructions with the unit so that they will be easily accessible.

Failure to read and follow these warnings and instructions could result in property

damage, serious injury, or death.

•ALWAY disconnect the pump from the power source before servicing or making

adjustments.

•NEVER handle the pump or motor with wet hands or when standing on a wet or damp

surface while the pump is plugged into the power source.

•MAKE URE THERE I A PROPERLY GROUNDED RECEPTACLE AVAILABLE. This pump is

wired with a 3-prong grounded plug. To reduce the risk of electric shock, be certain that

it is only connected to a properly grounded, 3-prong receptacle (preferably with ground

fault circuit interrupt). If you have a 2-prong receptacle, have a licensed electrician

replace it with a 3-prong receptacle according to local codes and ordinances.

•NEVER bypass grounding wires or remove the ground prong from the plug.

•DO NOT use an extension cord. The electrical outlet should be within the length of the

pump’s power cord, and at least 4 feet above the floor level to minimize potential

hazards from flood conditions.

•DO protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid

kinking the cord.

•MAKE URE the supply circuit has a fuse or circuit breaker rated to handle the power

requirements noted on the nameplate of the pump.

•DO NOT use the power cord or strain relief to carry the pump. Use the pump handle.

•DO NOT expose the control unit to rain or snow.

•DO NOT operate the pump or control unit if it has been damaged in any way.

•DO NOT use sump pumps in pits handling raw sewage, salt water, or hazardous liquids.

•DO NOT disassemble the pump or control unit. When service is required, contact

Glentronics technical support at 800-991-0466, option 3. Return the product to the

manufacturer for any repairs at the following address:

Glentronics, Inc.

640 Heathrow Drive, Lincolnshire, IL 60069

CAUTION

WARNING Risk of electric shock. To reduce this risk, observe the

following precautions.

To reduce the risk of hazards that can cause injury or

property damage, observe the following precautions.

ump Pumps

Instruction Manual &

afety Warnings

Items included:

Pump

Dual float and controller

Stainless steel hose clamp

2" x 1-1/2" reducer adapter

(on 3/4 P pump only)

You may also need:

1-1/2” or 2" rigid PVC pipe to

connect to the existing plumbing

A check valve or union

PVC pipe cleaner and cement

A surge protector

The Dual Float

& Controller

1/2 HP Pump

T1050

1/3 HP Pump

T1033

Note:

The 1/2 P pump will accomodate a 2" discharge pipe. owever, most

homes have 1-1/2" pipes. Therefore we have included a 2" x 1-1/2"

reducer adapter with this pump. You may replace your 1-1/2" discharge

pipe with a 2" discharge pipe, and a 2" adapter to obtain the optimum

gallons per hour.

1-1/2”

discharge

2”

discharge

• The control unit must receive 115V AC +/- 5% and 60 z from the AC outlet.

• These primary pumps will not provide protection during a power outage. With the

risk of property damage from high water levels, the addition of a Pro Series battery

backup sump pump system is highly recommended.

• After the initial installation, be sure to check the operation by filling the sump

with water and observing the pump operation through one full cycle.

• For continuous duty operation, the pump must be submerged at least 3/4 of the

depth of the pump at all times.

• In instances where the discharge line is exposed to freezing temperatures, the pipe

must be sloped downward so any remaining water will drain out. Failure to do so

will prevent water from exiting the sump and damage the pump if the line freezes.

Installation Instructions

Prior to Installation

1. Visually inspect your pump. Products may be damaged during shipping. If the

product has been damaged, contact your place of purchase or Glentronics, Inc.

before installation.

2. Thoroughly read the instructions provided to learn specific details regarding

installation and use. This manual should be retained for future reference.

1. Use a pit that conforms to all local

codes and is large enough to

accommodate the pump and float

switch. The minimum requirements for

the 1/3 P pump with the double

float assembly are 8⬙in diameter and

14⬙deep, for the 1/2 P pump they

are 10" in diameter and 16" deep.

However, larger sump pits are

preferred, since they will extend the

discharge cycle and reduce the

number of times the pump turns on.

2. Clean the pit of all debris. The

pump’s strainer must be kept clear.

3. The pump should not be set directly

onto a clay, earthen, or sand base.

You may install bricks or blocks under

the pump to provide a solid base.

4. The pump should be level.

5. Install discharge plumbing according

to local, regional and state codes.

Rigid PVC pipe is recommended.

6. An in-line check valve is

recommended to prevent back-flow.

This check valve is mandatory when sharing a discharge line with another pump

(i.e. a back-up pump or a second primary pump).

7. Install a gate valve or ball valve if required by any codes.

8. The pipe must be positioned in a downward slope so any remaining water will drain

away. Failure to do this will prevent water from exiting the pit and damage the

pump if the line freezes.

9. If you are replacing an old sump pump:

(a) Unplug the pump from the outlet.

(b) Loosen the check valve or rubber union by

unscrewing the bottom hose clamp. (If the

existing system is installed without a check

valve or rubber union, saw the pipe apart above

the sump pit.)

adapter.

(d) If the adapter fits into the new pump, screw the pipe into the pump. If not, cut

a piece of rigid PVC pipe and connect it to the new adapter by cleaning and

cementing the two pieces together. (Follow the instructions on the PVC cleaner

and cement.)

(e) Loosen the enclosed stainless steel hose clamp by turning the screw

counterclockwise and slip it over the pipe on top of the pump.

(f) old the float switch against the discharge pipe so the cage is below the bracket.

(g) Position the bottom of the float at the height you want the pump to activate and

turn the screw clockwise to tighten the hose clamp, but do not tighten it

completely at this time.

(h) Lower the pump into the sump by the handle.

(i) To avoid debris pouring into the float, it should be positioned on the side of the

discharge pipe opposite the drain tile. Note: It is desirable to mount the float

below the drain tile that empties into the pit. Mounting it above the drain tile

would allow water to fill the drain tile before the pump is activated. (See diagram).

(j) Once the switch is in the desired position, tighten the hose clamp.

(k) Connect the pipe on the pump to the existing discharge pipe with a rubber union

or check valve and tighten the hose clamps securely.

Connecting the Pump and Controller

Dual Float Controller

Plug the control box into a properly

grounded, 3-prong receptacle (preferably

with ground fault circuit interrupt), then

insert the pump plug into the receptacle

on the control box. You should provide

additional protection for the control unit

by using a surge protector.

For a neater installation, secure the power

cord and the float switch cord to the

discharge pipe with wire ties or hose

clamps. Keep the cords separated from

each other on opposite sides of the pipe.

Completing the Installation

1. After the initial installation, be sure to check the pump operation by filling the sump

with water and observing the pump through one full cycle. The pump should run for

10 seconds after the lower float drops. Note: When the p mp activates, it sho ld have

a “normal p mping” so nd. Any abnormal so nd, vibration, or lack of o tp t is the

signal of a problem. Stop the p mp and refer to the

tro bleshooting g ide.

2. Replace the pit cover making sure not to pinch or crimp

the pump wire with the cover. The pit cover either has

a ‘hole punch’ that will allow the cord to be passed

through or one can be drilled in the cover.

Product Operation

Dual Float witch

The dual float switch contains two large floating rings

enclosed within a protective cage. Water will lift the

WARNING

NOTICE

PUMP

WIRE

AIR BLEED

HOLE

FLOOR

JOIST SLOPE

PIPE

DOWN

SURGE

PROTECTOR

DISCHARGE

PIPE

GATE

VALVE

UNION/CHECK

VALVE

PRO SERIES

PUMP

DOUBLE

FLOAT

BRICKS

DRAIN TILE

FLOAT WIRE

DUAL FLOATCONTROLLER

PLUGGED INTO

AC OUTLET

PIT COVER

Controller

Dual Float

Considera Pro Series Battery

BackupSump Pump System

Glentronics,Inc. 800.991.0466 www.stopflooding.com

ModelNo.DFC1

This installation must be in accordance with the National

Electric Code and all applicable local codes and ordinances.

Make sure the outlet is single phase, 115V and 60HZ

for all the pump installations.

9C 9D 9F

SURGE

PROTECTOR DISCHARGE

PIPE

GATE

VALVE

DUAL FLOATCONTROLLER

PLUGGED INTO

AC OUTLET

PUMP

WIRE

FLOAT

WIRE

Controller

Dual Float

Consider a Pro Series Battery

Backup Sump Pump System

Glentronics, Inc. 800.991.0466 www.stopflooding.com

ModelNo. DFC1

bottom float by a 1⁄4⬙, which will activate the pump. If for any reason the lower float

does not activate the pump, the water will rise and activate the second switch. As the

pump evacuates the water from the pit the floats will drop. The pump will run for an

additional 10 seconds to extend the cycle after the lower float drops. Note: When

mo nting the float switch, position the bottom of the cage at the height yo want the

p mp to activate.

Dual Float Controller

The Dual Float Controller will activate the pump

when either float is lifted, and then shuts off

automatically 10 seconds after the float drops.

Plug the pump cord into the piggyback switch

on the control unit.

Operating the Pump in a Continuous

Duty Application

The Pro Series pumps are rated for continuous duty and may be used in applications

requiring continuous pumping including fountains, ponds, etc. For use in any

continuous duty application the pump should be plugged directly into the wall outlet

without the use of the controller. The outlet must be a single phase properly grounded

3-prong receptacle, 115V, 60 Z (preferably with ground fault circuit interrupt). For

contin o s d ty operation, the p mp m st be s bmerged at least 3/4 of the depth of the

p mp at all times.

Maintenance Check List

Maintenance should be performed 1-2 times per year.

1. Remove all debris from the bottom of the pit.

2. Remove all debris floating in the water.

3. Remove all debris from the float switch cage.

4. Fill the pit with water. Make sure pump turns on at the intended level.

5. While the pump is running, make sure pump is evacuating water at a good pace.

Backup Installation

When the power goes out, the Pro Series AC sump pumps will not operate. For

protection during a power outage, a Pro Series battery backup system

can be installed. There are three systems with matching batteries that will provide

protection. The illustration below is an example of a typical battery backup

installation.

PUMP

WIRE

PIT COVER

CHECK

VALVE

FLOAT

WIRE

FLOAT

WIRE

MAIN

A/C PUMP

A/C FLOAT

SWITCH

BATTERY

BACKUP PUMP

FLOAT SWITCH

BATTERY

DRAIN TILE

BATTERY

CABLE

OUTLET

BACKUP SYSTEM

CONTROL UNIT

PUMP

WIRE

DUAL FLOATCONTROLLER

PLUGGED INTO

AC OUTLET

SURGE

PROTECTOR

Controller

Dual Float

Considera Pro Series Batter y

BackupSump Pump System

Glentronics,Inc. 800.991.0466 www.stopflooding.com

ModelNo. DFC1

Visit our website www.stopflooding.com for more information about the Pro Series

AC sump pumps and battery backup sump pump products.

Dual Float Controller

Warranty

GLENTRONICS, INC. warrants to the end purchaser that its pumps, switch and control unit products are free from defective materials and workmanship for the periods indicated below:

All parts and labor (excluding installation) for a period of:

• 3 years from the date of purchase on the 1/3 P pump, when used intermittently as a sump pump

• 5 years from the date of purchase on the 1/2 P pump, when used intermittently as a sump pump

• 1 year from the date of purchase on all pumps, when used in continuous duty operations such as fountains or ponds

The defective product must be returned directly to the factory, postage prepaid with the original bill of sale or receipt to the address listed below. GLENTRONICS, INC., at its option,

will either repair or replace the product and return it postage prepaid.

Conditions

The unit must be shipped, freight prepaid, or delivered to GLENTRONICS, INC. to provide the services described hereunder in either its original carton and inserts, or a similar package

affording an equal degree of protection.

The unit must not have been previously altered, repaired or serviced by anyone other than GLENTRONICS, INC., or its agent; the serial number on the unit must not have been altered

or removed; the unit must not have been subject to accident, misuse, abuse or operated contrary to the instructions contained in the accompanying manual.

The dealer's dated bill of sale, or installers invoice must be retained as evidence of the date of purchase and to establish warranty eligibility.

This warranty does not cover product problems resulting from handling liquids hotter than 104 degrees Fahrenheit, handling inflammable liquids, solvents, strong chemicals or severe

abrasive solutions; user abuse; misuse, neglect, improper maintenance, commercial or industrial use; improper connection or installation, damages caused by lightning strikes; excessive

surges in AC line voltage; water damage to the controller; other acts of nature, or failure to operate in accordance with the enclosed written instructions.

GLENTRONICS, INC. WILL NOT BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES FOR BREAC OF ANY EXPRESS OR IMPLIED WARRANTIES ON T IS PRODUCT. SOME

STATES DO NOT ALLOW FOR T E EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR INDIRECT DAMAGE. T E ABOVE LIMITATION MAY NOT APPLY TO YOU. T IS EXPRESS WARRANTY S ALL

BE EXCLUSIVE AND IS IN LIEU OF ALL OT ER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY WARRANTY OF MERC ANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. T IS CUSTOMER'S EXCLUSIVE REMEDY FOR BREAC OF T IS WARRANTY, OR OF ANY IMPLIED WARRANTY NOT EXCLUDED EREIN, S ALL BE LIMITED TO

REPAIR OR REPLACEMENT OF T E PRODUCT.

For information or service contact: