Prostock 84-25050-03 Owner's manual

155238-001 12/03
6
Installation • Operation • Maintenance
84-25050-03 2000CFM
CAUTION:
READ INSTALLATION, OPERATION, AND MAINTENANCE
INSTRUCTIONS CAREFULLY FOR SAFE OPERATION.
Right Angle
Media Air
Cleaner
Warranty
Limited Warranty
This product comes with a two (2) year limited warranty on parts. The warranty provides that
a replacement will be furnished for any part of the product that fails in normal use and service
during the applicable warranty period specified, in accordance with the warranty’s terms. The
replacement part is warranted for only the unexpired portion of the original warranty.
All parts are warranted for a period of TWO (2) YEARS after the effective date. The effective
date is the date of installation if properly documented. Otherwise, it is the date of
manufacture plus twenty four (24) months.
STANDARD PROVISIONS AND CONDITIONS
The following terms are common to all of PROSTOCK’S individual product warranties.
THIS WARRANTY WILL NOT APPLY: a) to defects or malfunctions resulting from failure to
properly install, operate or maintain the unit in accordance with the manufacturer’s printed
instructions; b) to damage from abuse, accident, fire, flood, and the like; c) to parts used in
connection with normal maintenance, such as cleaning or replacing air filters; d) to units that
are not installed in the United States of America or Canada; e) to units that are not installed
in accordance with applicable local codes, ordinances and good trade practices; or f) to defects
or damage caused by the use of any attachment, accessory or component not authorized by
PROSTOCK.
SHIPPING COSTS: You will be responsible for the cost of shipping warranty replacement parts
from our factory to our PROSTOCK distributor and from the distributor to the location of your
product. You also are responsible for any shipping cost of returning the failed part to the
distributor. (If in Alaska, Hawaii, or Canada, you also must pay the shipping cost of returning
the failed part to the port of entry into the continental U.S.)
SERVICE LABOR RESPONSIBILITY: This Warranty does not cover any labor expenses for service,
nor for removing or reinstalling parts. All such expenses are your responsibility, unless a service
labor agreement exists between you and your contractor.
HOW TO OBTAIN WARRANTY PERFORMANCE: You must promptly report any failure covered
by this warranty to the installing contractor or distributor. Normally, the installing contractor
from whom the unit was purchased will be able to take the necessary corrective action by
obtaining through his PROSTOCK distributor any replacement parts. If the contractor is not
available, simply contact any other local contractor handling PROSTOCK products.
The name and location of a local contractor can usually be found in your telephone directory
or by contacting a PROSTOCK distributor. If necessary, the following PROSTOCK office can
advise you of the nearest PROSTOCK distributor:
P.O. Box 17010 • Fort Smith, Arkansas 72917-7010 • [phone] • (For CA only: [phone])
HOWEVER, ANY REPLACEMENTS ARE MADE SUBJECT TO VALIDATION BY PROSTOCK OF IN-
WARRANTY COVERAGE.
An item to be replaced must be made available in exchange for the replacement.
MISCELLANEOUS: No one is authorized to make any warranties on behalf of PROSTOCK. ANY
IMPLIED WARRANTIES, INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, SHALL NOT EXTEND BEYOND THE APPLICABLE WARRANTY PERIODS SPECIFIED
ABOVE, PROSTOCK SOLE LIABILITY WITH RESPECT TO DEFECTIVE PARTS SHALL BE AS SET
FORTH IN THIS WARRANTY, AND ANY CLAIMS FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARE EXPRESSLY EXCLUDED. Some states do not allow limitations on how long an
implied warranty lasts, or for the exclusion of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
This Warranty gives you specific legal rights, and you may also have other rights that vary from
state to state.
P.O. Box 17010 • 3900 South Zero Street • Fort Smith, Arkansas 72917-7010
Phone: [phone] (For CA only: [phone])
¤

Table of Contents Page
Introduction ......................................................1
Specifications......................................................2
Installation..........................................................3
Maintenance ......................................................5
Warranty ............................................................6
Table of Contents Maintenance
5
Maintenance
The filter cartridge in your air cleaner must be replaced
periodically. The frequency of filter replacement is best
determined by visual examination. On average, filter
cartridges should be replaced every 9-12 months with
normal usage.
Steps for Replacing Filter Cartridge
1. Open access door by lifting the handle and pulling the
bottom of the door toward you. Remove door
completely.
2. Tilt used filter cartridge to allow filter to be removed
from cabinet. Pull used filter cartridge from cabinet.
3. Discard dirty filter cartridge in plastic bag in which
replacement filter was received.
4. Slide new filter cartridge into cabinet with “AIR FLOW”
arrow pointing in the direction of air flow. Care shall be
exercised to place filter cartridge in angle holders on
bottom and side of cabinet.
5. Replace access door.
Note: Your installing dealer can supply media air cleaner
replacement filter cartridges. Remember, periodic inspection
and replacement of your filter will ensure high efficiency air
cleaning with the frequency of filter replacement best
determined by visual inspection.
Air Cleaner
Part No.
84-25050-03
Model
(CFM)
2000
Filter Cartridge
Size
5 x 19 3/4” x 24 1/4”
Replacement
Filter Cartridge
Part Number
54-25051-01
Number
Per
Carton
3
Vendor
Number
252990-102

Select location for the Air Cleaner
Select a location that is readily accessible for
periodic inspection and cleaning. Allow a minimum
of 30” in front of the access panel for filter
removal.
Direction of Airflow Through the Air Cleaner
Note: The air cleaner is designed for easy access
from either side. Select the location and locate air
cleaner opening next to furnace. Install the door
handle on the front panel to allow easy access for
filter cartridge removal. The direction arrow on
the filter cartridge must point in the direction of
air flow.
Mounting holes are provided in the air cleaner
cabinet for duct work attachment. The .140” holes
are sized for #8 sheet metal screws or 1/8” rivets.
Installation
Introduction
Your media air cleaner is a high efficiency air filtration
device designed to remove dirt, dust, pollen and other
microscopic particles from the air passing through it.
How it works
Dirty air enters the air cleaner by way of the return air
duct system in your home. Particles are collected by
the special pleated filter media. The pleats provide an
exceptionally large filtering face area in a very
compact space which allows maximum dirt holding
capacities with minimum air flow resistance.
G
r
e
a
s
e
S
o
o
t
D
u
s
t
D
i
r
t
P
o
l
l
e
n
s
S
p
o
r
e
s
Clean Air
Introduction
4 1

Dimensions
Capacity in CFM
600
800
1000
1200
1400
1600
1800
2000
Pressure Drop
Inches W.G.
.03
.05
.07
.10
.14
.18
.22
.27
Specifications
Application
The air cleaner is is to be installed in a forced air
heating, cooling, and ventilating system. It should be
installed in the system such that all the system air is
circulated through the air cleaner. The air cleaner will
only remove the airborne contaminants delivered to it;
therefore maximum performance is obtained when the
system blower is set for continuous operation.
Installation Requirements
Locate the air cleaner in the return air duct next to the
blower compartment. In this location, the blower
motor and cooling coils will be kept clean.
Air Conditioning
The air cleaner should be installed upstream of the
cooling coil to keep the coil clean and reduce air
conditioning coil maintenance. Improved cooling
efficiency is the result of clean coils which directly
affects energy costs. Failure to replace filter cartridge
can cause damage to cooling system and increase
utility bills.
Sheet Metal Installation
This right angle media air cleaner is adaptable to all
new or existing residential forced air furnace and
cooling systems with Highboy Space Saver or offset
installation.
Air Cleaner Installation and Maintenance
This right angle media air cleaner has been designed
specifically for highboy furnaces and direct installation
to your heating and cooling system return air duct.
The duct opening of your air cleaner is supplied with
an adjustable inlet flange.
The unit is shipped with the flange set at 24” x 8”. If
the incoming duct is 24” x 8”, attach the duct directly
to the flange and secure with sheet metal screws
through the pre-drilled holes.
If flange requires adjustment to 24” x 10”, remove the
five #6 sheet metal screws securing the flange to the
cabinet. Adjust flange to 24” x 10” and secure with
screws. Proceed with installation.
Traditional Installation
of air cleaner
Installation of Right Angle
Media Air Cleaner
Installation
2 3