Prostock PSBTWE1000 User manual

INSTALLATION
GUIDE
Electronic Bidet with
Integrated Toilet
#PSBTWE1000

Electronic Bidet Installation Guide 1
INSTALLATION MANUAL
Thank you for choosing our product! Please read and carefully follow the instructions before
installation. Secure this manual for maintenance and future reference. We reserve the right to the
final interpretation of this manual. This manual is subject to change without notice.
Improper use of this products may result in serious injury or death. Do not use this
product in a wet or damp place, such as a shower or bath tub, as this may cause electric
shock. This product should only be used with 120V electrical voltage to avoid fire or
electric shock. Always plug the grounded plug into a GFCI Protected outlet to prevent
electrical shock. Do not use a damaged plug or cord or insert into a faulty electrical outlet.
Improper use of this product may result in personal injury or property damage. Always
follow these installation instructions. Improper installation may result in water damage,
electrical shock, or fire.
WARNING
CAUTION
PREPARATION
Before installation begins, please confirm that you have the materials indicated below:
INCLUDED
NOT INCLUDED
Supply stop valve, Closet bolts, or 3/8”x7/8” water supply line
RECOMMENDED TOOLS
Electronic Bidet
Pencil
Remote Control
Masking or
painters tape
Installation Manual
Tape measure
or ruler
Wax Ring
7/16” ratchet box
wrench or deep socket
ratchet wrench
Carpenter’s
square or other
straight edge

Stop Valve
Temporary Line
Closet Flange
(Drain)
INSTALLATION:
1. Water Supply and Alignment Prep
• Install the supply line (not included) to water supply inlet
located the back of the tank. To prevent leaks, use an
adjustable wrench to tighten the nut and seat the O-ring.
(This step is easier to do now when it is not up against a
wall, but can also be done once the toilet is installed
and secured in place.)
• Draw temporary lines on the floor that are parallel to the
wall which align with the center of the closet flange in the
floor. (Make sure to exceed the width of the toilet by
approximately 3” in each direction)
• From the back of the toilet, measure and place a 2” piece of tape along the bottom edge
of the toilet, from approx. 7”-9”. Repeat on both sides of bowl.
Electronic Bidet Installation Guide 2
• Once the tape is placed, measure 7-3/4” and draw a vertical line on the tape. Repeat for
both sides of the bowl. These marks will help you guide the bowl only.

2. Setting the Toilet
Electronic Bidet Installation Guide 3
This toilet is heavy; we suggest utilizing two
people and opening the seat cover for better
hand holds while setting the bowl in place.
WARNING
• Install the wax ring onto the closet flange.
• Install closet bolts (not included) and align
them with the temporary center lines
on the floor.
• Install the bowl onto the flange by
lifting the toilet over the closet flange
and, using the lines on the tape
and temporary center lines on the
floor as your guide, align the toilet
over the bolts and gently set the toilet
onto the wax ring.
• Help the bowl “settle” onto the wax ring
by pushing down to add weight on both
front to back and side to side.
• Once the toilet is set, reach through the back of the bowl behind the toilet and locate the
closet bolts. Place a washer and nut over each bolt. Hand tighten the nuts until they come
to rest on the washers.
• Using a 7/16” wrench of your choosing and, alternating from side to side, gently tighten the nuts
onto the washers until the toilet has little to no play (wiggle room) against the floor.
Be careful to not over tighten or you may crack the toilet!
Wax Ring
Toilet Drain
Outlet
3. Securing the Bowl

Electronic Bidet Installation Guide 4
• Caulk the edge of the toilet bottom with
a mildew resistant caulk designed for
indoor bathroom applications. This will
help to keep the bowl in place and give
added security and strength
to the closet bolts.
4. Applying Caulk
Caulk
• If you have already connected the supply line to the toilet skip to the next step. If not, install
the 3/8”x7/8” supply line (not included)to water supply inlet located the back of the tank.
To prevent leaks, use an adjustable wrench to tighten the nut and seat the O-ring.
• Connect the smaller (3/8”) end of the water supply line to previously installed supply stop valve.
To prevent leaks, use an adjustable wrench to tighten the nut and seat the O-ring.
5. Installation of supply line
Water
Inlet
Stop Valve
New
Hose