32” Kitchen Display System
All Right Reserved Copyright 2012
KS-1330
All Rights Reserved. Copyright 2017
Jumper Setting
Safety Precaution
• Don’t allow foreign objects to fall into this product.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry
cloth.
• Never use strong agents such as benzene and thinner to clean the system.
If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and
then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner
for computers.
• Don’t contact the surface of capacitive touch before entering your operation system, or capacitive
touch may have position problems for electrostatics interface.
• Don't exchange the M/B battery by yourself or serious damage may incur.
The following messages are reminders for safety on how to protect your systems from damages and to
extend a long life of the system.
1. Check the Cable Voltage
• Make sure the range of operating voltage between AC 100~240V. Otherwise, the system could be
damaged.
2. Environmental Conditions
• Place your KS-1330 on a sturdy, level surface. Be sure to allow enough space to have easy
access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using it outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0~35°C (32~95°F).
• Avoid moving the system rapidly from a hot place to a cold one and vice versa for condensation
may come from inside of the system.
• Place KS-1330 in strong vibration(s) may cause hard disk failure.
• Don’t place the system close to any radio active device in case of signal interference.
3. Handling
• If the system isn’t fully in DOS mode, adjust BIOS setting as the instruction:
Advanced Chipset Feature →Boot display →choose “LFP”.
• Avoid putting heavy objects on top of the system.
• Don’t turn the system upside down. This may cause the hard drive to malfunction.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly
recommend that qualified engineers can open and disassemble the system. The LCD and Touchscreen are
easily breakable, please handle them with extra care.
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly. Replace batteries only with the same or equivalent type recommended by the manufacturer.
Dispose the used batteries according to the manufacturer’s instructions.
JCOM_DVII1 JCOM2_3
JAUDIO1
JSATA_PWR1
DIMM1
JLAN_USB2 JLAN_USB1 JKB_MS1
SP1
JP10
1
2
5
6
JPCOM4
JPCOM3
JSYS_FAN1
2
65
1
5
2
1
JLVDS1
30
291
2
1
JINV1
6
MPCI_E1
14
JCOM5
JCOM4
15
6
1
6
10
5
10
JCOM6
JFP1
12
11
2
1
JP7
1
5
10
1
6
JDIO1
1
2
JUSB1
9
10
1 2
JP14
JP15
1
2
5
6
JP4
1
JP5
1
JP9
PCI_E1
JBAT1
Intel® Bay Trail E3827
SOC
JP1
1
1
1
2
5
6
1
2
71
72
73
74
203
204
JLPC1
20
19
2
1
1
2
7
8
A11
A1
A12
A18
B11
B1
B12
B18
12
15 16
17 18
51 52
VGA
VGA/DVI Selection
DVI
(default)
5
6
1
2
5
6
1
2
2
1
RI
(default)
5
62
1
6
5
12V
2
1
6
5
5V
COM3 Voltage
Selection
(default)
Auto-On
1
Select by
BIOS
1
Power-On Mode
Selection
(Default for
BS-H292 (SBOX))
2
RI
(default)
12V
5
1
56
12
56
12
5V
COM4 Voltage
Selection
(Default for
BS-H292
(SBOX))
2
6
5V
LVDS Power Selection
1
3.3V
1
(default)
Backlight Enable Selection
5V
1
3.3V
1
(default)
(default)
Backlight /Inverter PWM
Voltage Selection
1 1
5V3.3V GND
1
(default)
1920x1080 2CH/24bit (default)
LVDS Resolution Selection
5
6
1
2
JP14 JP15
5
6
1
2
DIMM2
JSATA2
JSATA1
JCPU_FAN1
1 4
17
17
1
2
71
72
73
74
203
204
14
JDC_PWR1
14 14
JSATA_PWR2
1 1
Clear
CMOS
Clear CMOS Data
Selection
Normal
(default)
